Top 20 Kyocera FS-3900DN Laser Printer - Page 4 Questions & Answers


Usually a printer doesn't lie when it indicates a paper jam, if you have checked as thoroughly as possible and no paper can be found. It is possible that the paper just isn't feeding and a printer will sometimes indicate a paper jam when paper doesn't feed. But if this isn't the case and a jam is indicated as soon as you turn the printer on, one of the plastic jam sensing actuators may be broken or hung up.

Kyocera... | 1,514 views | 0 helpful votes


It is a "mechanical error". The part after the colon is the number of pages printed. It's probably worthwhile taking the trays, toner and cartridge out and opening all the access doors and checking for something obvious before calling in an engineer.

Kyocera... | 995 views | 1 helpful votes


push the drum until it clicks
power off/on

Kyocera... | 5,134 views | 6 helpful votes


try chaning the quality of the envelope, some do not respons well to heat.

Kyocera... | 468 views | 0 helpful votes


some files may be corrupt: Best is try to reinstall printer software with original drivers to ensure that correct files are installed.

Kyocera... | 580 views | 0 helpful votes


could be a hundred reasons, most likely is the rollers are worn try rubbing the rollers with a scouring pad which will give them a bit more friction to grab the paper with, this is only a temperary fix though!

Kyocera... | 214 views | 0 helpful votes


You have pulled the drum unit out of position possably after changing the waist toner ? Open the back cover, open the frunt cover and remove the developer unit, the full unit not just the toner, open the side cover where the waist toner bottle is and push the drum unit back into place until it clicks, put the dev unit back in place and close everything reboot the machine

Kyocera... | 754 views | 5 helpful votes


In printer properties.

Kyocera... | 5,209 views | 0 helpful votes


please install drum or toner unite or clean laser unite if you are not success then chack fuser unite

Kyocera... | 460 views | 0 helpful votes


Try downloading the manuals from Kyocera :
http://www.kyocerasupport.co.uk/index/download_center.false.driver.FS3900DN._.EN.html#


Please take a moment to rate this solution. Thanks.

Kyocera... | 484 views | 0 helpful votes


Try a new bottle. I've seen where the there's enough old toner clining to the sides of the bottle that prevent the sensor from seeing through it. Of course the sensor and led may be covered with old toner. Get in there with a vacuum when the machines off and clean it out.

Kyocera... | 258 views | 0 helpful votes


Error code 7410 indicates that the drum unit is not installed correctly. This is usually caused by dirty contacts or a faulty drum unit chip. First remove the toner and developer unit, then the waste toner bottle. Unlock and remove the drum unit by depressing the catch that sits behind the waste toner bottle and pulling the unit out to the L/H side. Be very careful not to scratch the drum and avoid strong light as it is easily damaged. Clean up all contacts and refit in reverse order. Hope this helps, if not you may need to buy a new drum unit.

Kyocera... | 738 views | 5 helpful votes


Right click on the printer icon and choose properties. Your emulations are listed there.

Kyocera... | 1,874 views | 1 helpful votes


Hi,

This means your conection is or should be

Parallel port no 3

check your cabling is correct

Regards
Richard.

Kyocera... | 73 views | 0 helpful votes


The fault is described correctly by tigertail - howerver this is not a chargeable repair as the 0150 fault is due to a problem at manufacture so being out of warranty does not matter.

Call the support line and you will have to pay for delivery to the repair center but repair is free and return postage is free.

0845 456 0456 Kyocera Mita

Thanks

Russ

Kyocera... | 185 views | 0 helpful votes


0150 - Engine PWB EEPROM error. Detecting engine PWB EEPROM communication error.

Solutions:
1. Switch the printer OFF; unplug the power cable; wait 20 seconds; plug in the power cable; switch the power ON, If the error comes back follow the next solutions:
2. Update / Burn the latest firmware version. You may need to call a Kyocera Service Provider because you need a CF card (compact flash memory card) and the FIRMWARE.
3. Replace the Engine PWB (a board) - again you have to call a Kyocera Service Provider.

Kyocera... | 841 views | 1 helpful votes


If you pull the fuser out, look at the bottom of the sliding mechanism for a bent metal tab that actuates a switch when you close the rear drawer.

They get bent pretty easily.

Kyocera... | 358 views | 0 helpful votes


Very weird message! Pull down the by-pass tray in the front of the printer and insert a sheet of paper , then print.

Kyocera... | 424 views | 2 helpful votes


Please leave an email and I'll sent you the manual...

Kyocera... | 74 views | 0 helpful votes


No, after letterhead is finished load into by-pass tray and continue with the form printering

Kyocera... | 37 views | 0 helpful votes

Not finding what you are looking for?
Kyocera FS-3900DN Laser Printer Logo

189 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

FS Kyocera

  • FS Kyocera

Most Popular Question

error call service 4000 00433933

  • Office Equipment & Supplies
Loading...