20 Most Recent Frigidaire GLTR1670A Front Load Washer Questions & Answers

Spider arms attached to stainless steel drum inside of tub have probably broken. This is a known problem with Frigidaire front loading washing machines. The stainless steel drum has a 25 year warranty but this does not include the spider arms. You cannot buy the spider arms separately, you have to buy the unit as one. The drum cost about $250.00 and probably about $300.00 in labor to install. You can do it yourself but it is pretty involved. Good Luck!

Frigidaire... | Answered on Oct 09, 2019

I have had to change the door switch on every washer and drier I have ever had. Just a thought: If the door switch is bad the drier and washer will not start working. The one I changed on my drier about a month ago, when I opened the door and played with the switch while pushing the start button it finally came on. I changed the switch and no more problems. If the door is open the dryer and washer are not supposed to operate. I have changed some which you could not move around on those I would pull the wires off the door switch. Depending on if the switch is normally open or closed I would connect the two wire and try to start or leave them separate and try to start..

Frigidaire... | Answered on Nov 19, 2017

Time for a new one.
Sound like you have done the main shaft bearing.

Frigidaire... | Answered on Nov 18, 2017

not sure if this link will help you find out why,but have a look.
After wash clothes all smell like oil gas from machine Google Search

Frigidaire... | Answered on Nov 03, 2017

i tell customers to remove the drain hose from the stand pipe and vacuum the water out of the washer from the drain hose but because of the pillow this might not work in your case. Now remove the two screws on the front lower panel and pull the panel
in side you will see the drain pump if you did not have a shop vac go to the auto parts store and buy a pair of radiator hose clamps and clamp the hose line as close to the washer as possible.(but put down some towels as water always stays there) then pull the tub to pump hose by depressing the squeeze clamp(now while your at the auto parts id get a screw clamp to replace the spring clamp it makes putting the hose back on a lot easier)pull the hose off.Then pull the pump to drain hose off .Remove the two 5/16 in screws securing the pump to the washer base.Unplug the connector and remove the pump inspect the pump for foreign objects,broken or stripped impeller blades . if the impeller are stripped you will have to replace the pump then form the front of the washer take a piece of water hose with one end cut off and run it down the pump to drain end of the drain and reassemble the unit

Frigidaire... | Answered on Sep 06, 2015

Thank you for your inquiry, Jay Kraemer!

From the information you have provided you would like a video on how to balance your Frigidaire frontload washer. I was unable to find any information on balancing your washer from your manufacturer. This could mean that it is not a simple DIY job. You may be able to perform a generic search online for any information except I would recommend having a professional technician out to accurately balance your washer. This will help to avoid any future issues. -Matt

Frigidaire... | Answered on Feb 20, 2015

Kathy, you may have the beginnings of a tub bearing failure. What usually happens is the water seal fails on the tub drum shaft. This lets water into the bearing cavity and usually some grease migrates out into the drum. What eventually happens is the wash water eventually washes the grease out of the bearings and they fail. You will notice your spin cycle getting louder and louder.
You can check for a loose tub bearing by lifting the drum gently at the top. Is there play where the drum can move vertically, independently of the outer assembly? That's my guess. You can do an internet search about tub bearing replacement if you want to get into that. Its doable, depending on your skill level. Good luck.
Been there and done that. Usually Frigidaire doesn't sell the bearings, but they are standard bearings and you can usually match up a seal.

Frigidaire... | Answered on Mar 21, 2014

you will have to remove the rubber around the door if not the whole m/c will have to be striped even taking the rubber of its still a faf to get at

Frigidaire... | Answered on Jan 05, 2013

do not set knob to open position and open door ....I did this and flooded new construction. What happened to me is that my contractor took out the screens to the inlet hoses and this allowed small chunks to get through and lodge in solenoide valve causing it to stick open and allow for constant water flow......simple disassemble, clean, and PUT SCREENS BACK IN! they are there for a reason...

Frigidaire... | Answered on Dec 19, 2012

You will need to remove the drain boot that runs between the tub and the pump and clear the filter.

Frigidaire... | Answered on Dec 11, 2012

Remove the front bottom kickplate and then remove the boot form the tub to the pump and be sure it is clean.

Frigidaire... | Answered on Dec 05, 2012

Not finding what you are looking for?
Frigidaire GLTR1670A Front Load Washer Logo

174 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Frigidaire Washing Machines

  • Frigidaire Washing Machines

Most Popular Question

video showing balance front load washer

  • Washing Machines