20 Most Recent Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E Questions & Answers


Hi, if you installed a Supervisor 6L-E 10GE (X2) in the new 4506-E and you want to use the two 10GE uplinks as Gigabit, you need to type in the following config lines:

hw-module module 1 port-group 1 select gigabitethernet
hw-module module 1 port-group 2 select gigabitethernet

Cisco Catalyst... | Answered on Jun 20, 2014


http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/installation/guide/78-14409-08/04replac.html.......................... please follow the above link

Cisco Catalyst... | Answered on Feb 25, 2011


Please make sure you have only one supervisor module installed on your switch or else pull out the backup sup module and do this activity .

In the last step of reset it will ask to save the config.

do you wish to save this configuration? y/n [n]: y
You must reset or power cycle for new configuration to take effect

do not forget to type in y there.

Cisco Catalyst... | Answered on Jan 11, 2011


Hi

Ok so once you have logged into the router you do the following

go into enable mode by tyoing in en
Then type in conf t
then type in int X where X = the interface
then type in speed 100
then type end

This will set the interface to 100mbps

Cisco Catalyst... | Answered on Mar 02, 2010


Please see Cisco's page at http://www.cisco.com/en/US/products/hw/routers/ps5199/products_password_recovery09186a0080093e12.shtml
for step by step details and more in depth instruction.

1. Reboot
2. Press the "break" button on your keyboard within 60 seconds of the power-up to put the router into ROMMON mode.
3. confreg 0x2142
4. reset
5. type, "no" when prompted to enter the initial configuration dialog.
6. enable
7. copy startup-config running-config
8. conf t
9. enable secret <password>
11. config-register 0x2102
12. reboot again

Cisco Catalyst... | Answered on Feb 19, 2010


Hi

I have checked and no data found for that S/N

Thanks

Cisco Catalyst... | Answered on Nov 26, 2014


Hi

Instructions
telnet to the IP address of the Cisco switch
Enter the telnet access password for the Cisco swict when requested, and then the "Enter" key.
Type "enable" at the command prompt, and then the "Enter" key.
Enter the Privileged Exec password when requested at the command prompt, and then the "Enter" key. Then enter "configuration terminal" at the command prompt, and then the "Enter" key.
Type "interface fastethernet0/1," replacing the "fastethernet0/1" with the name of an interface in which you wish to enable PoE, and then the "Enter" key. Then, while in interface configuration mode, type "power inline auto" and then the "Enter" key. Repeat this step for each interface in which PoE is required.
Type "end" at the command prompt and then the "Enter" key, copy running-config
Below is some commands to run, I don't have any power on the interface but this will show you if this is working...
SW1#sh power inline fastEthernet 0/1
Available:360(w) Used:0(w) Remaining:360(w)
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Fa0/1 auto off 0.0 n/a n/a 15.4
Run this command to see the interface is up.....
SW1# sh interface fastEthernet 0/1 ' in protocol
FastEthernet0/1 is up, line protocol is up (connected)
SW1#sh cdp interface fastEthernet 0/1
FastEthernet0/1 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds


Thanks

Cisco Catalyst... | Answered on Nov 26, 2014


Fuel Temperature Sensor "B" Circuit High Input
- Faulty Fuel Temperature Sensor
- Fuel Temperature Sensor harness is open or shorted
- Fuel Temperature Sensor circuit poor electrical connection

Cisco Catalyst... | Answered on Aug 29, 2014


You can only reset password this way:
1.
Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) to the console port of the switch.
Use the following terminal settings:
  • Bits per second (baud): 9600
  • Data bits: 8
  • Parity: None
  • Stop bits: 1
  • Flow Control: Xon/Xoff
2.Unplug the power cable.
3. Hold down the mode button located on the left side of the front panel, while you reconnect the power cable to the switch
4. Release the Mode button when the SYST LED blinks amber and then turns solid green. When you release the Mode button, the SYST LED blinks green.
5. switch: flash_init
6. switch: load_helper
7. switch: dir flash:
8. switch: rename flash:config.text flash:config.old
Rename config.text to config.old. In that file the password is stored.
9. switch: boot
10. Enter "n" at the prompt to abort the initial configuration dialog
11. Type en to enable
12. Switch#rename flash:config.old flash:config.text
13. Switch#copy flash:config.text system:running-config
14. Overwrite the current passwords:
conf term
enable secret <new pass>
enable password <new pass>
line vty 0 15
password <new pass>
login
line con 0
password <new pass>

15. write memory
16. copy run start

Cisco Catalyst... | Answered on Jun 20, 2014


DO YOU HATE ALL THE SPAMMERS AND SPAMMING HERE ON FIXYA ??? USE ANY NUMBER HERE. CALL A SPAMMER AND HAVE SOME FUN TODAY!! ALL TOLL FREE TOO!!
THIS IS A COLLECTIVE PHONE LISTING OF ALL THE SPAMMERS HERE ON FIXYA. WE SUGGEST YOU DONT CALL ANY OF THEM UNLESS YOU KNOW WHAT YOU ARE DOING !!
1-85O-8I2-4OO9 1-8OO-8O3-1O69 1-888-499-5520 1-877-769-0969 1-888-499-5520 1-8OO-828-O294 888-348-1833 1-888-444-6538 1-855-616-7697 l-855-892-OO6O 1-888-570-9791 1-855-26O-OO64 1-855-536-5666 1-844-24O-9111 1-8OO-55O-5195 1-845-481-1722 1-855-616-7697 1-844-819-3382 1-855-221-4867 1-845-481-1722 1-800-258-1449 1-845-764-4808
IF YOU KNOW WHAT YOU ARE DOING HAVE SOME FUN WITH THESE LOSERS AND LETS BEAT THEM AT THEIR OWN GAME.. CARRY ON31

Cisco Computers... | Answered on Nov 12, 2019


You can get best cisco router support phone number at Toll Free Number ( 1-877-769-0969 ). Cisco router Tech Support number ( 1-877-769-0969 )

Cisco Computers... | Answered on Nov 12, 2019

Not finding what you are looking for?
Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E Logo

Popular Tags

10 questions posted

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Catalyst Cisco

  • Catalyst Cisco

Most Popular Question

just replaced cisco 4506

  • Computers & Internet
Loading...