Top 20 Copystar Kyocera FS-1135 MFP/DP Multifunction Printer Questions & Answers


try emptying the waste toner from drum unit

Copystar Kyocera... | 784 views | 0 helpful votes


It's one unit with the drum

Copystar Kyocera... | 1,082 views | 0 helpful votes


I can not find the screw razor is talking about.

Copystar Kyocera... | 2,905 views | 0 helpful votes


By calling a service agent and arranging a repair visit

Copystar Office... | 30 views | 0 helpful votes


Sounds to me like you need a developer change and these machines must have OEM toner

Copystar Office... | 50 views | 2 helpful votes


it is the touchscreen

Copystar Office... | 82 views | 0 helpful votes


try 1087 1087 then 20 and 21

Copystar Office... | 192 views | 0 helpful votes


try youtube or google iys hard to explain you have to remove the gray

Copystar Office... | 51 views | 0 helpful votes


you need to run the simulation 130 in order to add toner to the developer, after that you will be good.

I’m happy to help further over the phone at https://www.6ya.com/expert/mustafa_06f84c65ab5cc745

Copystar Office... | 58 views | 0 helpful votes


Is it a stolen copier?

Just kidding....

Check for dirt/dust and/or broken paper in roller tracks.

Copystar Office... | 177 views | 0 helpful votes


Make sure your default settings are for AUTO paper selection and 100% magnification to start. That is the most common default settings. Then, under "Zoom" change to AUTO magnification and under PAPER SELECTION specify Letter (either landscape or portrait). Now when you copy a legal original (8.5" x 14") it will be reduced at 78% to fit it on an 11" sheet. An alternative is to use "X-Y" zoom. Now you can stipulate 78% for the "X" dimension and leave the "Y" dimension at 100%. You will want letter size paper to be feeding lengthwise (portrait). Now you can copy legals and the image is reduced top-to-bottom only, leaving it much more readable.

Copystar Office... | 110 views | 0 helpful votes


You first need to pull the fuser out and manually check that it is running smoothly. More times than not, it will be the fuser rather than the motor.

If the fuser is fine, locate the motor then turn the machine on and visually inspect. If the motor does not run before the code pops up then replace it.
/uploads/images/copystar-c2300-error-code-34884244-4-1.jpg

Copystar Office... | 1,086 views | 0 helpful votes


No question.

Copystar Office... | 42 views | 0 helpful votes


1087 1087 then 201 push little crosses with pen tip

Copystar Office... | 59 views | 0 helpful votes


If it is a c-3200 code it means that you have a exposure lamp problem.Defective scanner,defective scanner PCB,lamp or inverter board,incorrect shading,poor contact of the connector terminals on lamp assembly. Look for a bad connection And look at lamp. Look for blue rings or burnt ends. Now don't look at that light while its on.

Copystar Office... | 75 views | 1 helpful votes


fuser motor lock. bad fuser or exit turnover assembly not rotating properly. the duplex unit could also bind causing this. run u030 in service mode to check the motor.

Copystar Office... | 139 views | 0 helpful votes


if this were your problem it would be obvious the inner tray is in the middle of the machine there is a lever that lifts up as paper stacks up its probably stuck in raised position

Copystar Office... | 6,037 views | 0 helpful votes


The Ri 2530/3530 is termed a Digital Copier/Network Printer. Therefore it would need an ethernet connection to your local area network (LAN) and does not appear to directly connect to a computer. The spec states: Connectivity / Interface: Standard 10/100BaseTX, Parallel IEEE1284, Serial RS-232C.
As it is 2001, you next need a valid software driver to print - it is quoted as Windows OS Compatibility: Windows 95/98/Me/NT4.x/2000/XP. The following web site should help you.
Product Details

Copystar Office... | 97 views | 0 helpful votes


You have to be in the fax screen and find your User install or Initial settings screen. Redial can be set there. There's a default setting that I think you can set to "0" redials. I haven't had that manual for a long time.

Copystar Office... | 58 views | 0 helpful votes

Not finding what you are looking for?
Copystar Kyocera FS-1135 MFP/DP Multifunction Printer Logo

4 questions posted

Ask a Question

Usually answered in minutes!

Top Copystar Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Tammie Duggan
Tammie Duggan

Level 2 Expert

57 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Copystar Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Copystar Office Equipment & Supplies

  • Copystar Office Equipment & Supplies

Most Popular Question

fix developer unit not installed

  • Office Equipment & Supplies
Loading...