20 Most Recent Omega 1000 Juice Extractor - Page 2 Questions & Answers


With some difficulty. Sometimes replacement latch arms are not an exact fit for
older models. You may have to file them down a bit so they will snap in place.
Also make sure the fit at the cover is not too snug or else the arm will break again.
Removing the 4 screws on the bottom and separating the base will give you a better
view on what has to be done.

Omega 1000 Juice... | Answered on May 02, 2011


What's wrong with your juicer, maybe I can help?

Omega 1000 Juice... | Answered on May 02, 2011


Is this a new cover? There is an adjustment. On the bottom of the machine, dead center,
there is an adjustment screw with a locking nut. Unlock the nut and the turn the screw
counter clockwise, this will lower the motor shaft and consequently the blade. Once you
have clearance and install the cover, turn the screw clockwise until the blade contacts the
chute, back it off a half turn and lock her down. This will establish the correct gap between
the chute and blade. Also if your chute is ever chipped or scored by the blade because
of excessive vibration, you can file the chute level and readjust the gap.

Omega 1000 Juice... | Answered on May 02, 2011


I'm guessing it's busted. If you want to wire in a new one on your own, remove the 4
screws on the bottom of the juicer and separate the base. Omega at 1 800 633 3401,
should be able to sell a new one or give you advice where to get it repaired.

Omega 1000 Juice... | Answered on May 02, 2011


Just looked at mine because I thought there also might be an interlock switch
where the latch arms snap shut. There isn't one, at least on this one. Yours
might be a newer edition, so make sure the latch arms are fully seated and
snapped closed. You can also call Omega at 1 800 633 3401 and run it by
them. The reset switch should be in the pushed in position, it will pop out if
it's tripped.

Omega 1000 Juice... | Answered on May 02, 2011


Try the reset button on the bottom of the juicer.

Omega 1000 Juice... | Answered on Apr 26, 2011


Undo the latch arms, remove the cover then the clutch nut in the center of the
blade. Everything should lift out.

Omega 1000 Juice... | Answered on Apr 26, 2011


Best way to do it is remove the four screws on the bottom to separate the base
and work from the inside. Sometimes the newer latch arms are not an exact fit
and you may have to do a little filing here and there especially if it's a tight fit over
the lid.

Omega 1000 Juice... | Answered on Apr 26, 2011


Make sure it is assembled correctly and the latch arms snap shut completely
without any undue force. Also on the bottom of the juicer there should be a
reset button that might have tripped, just push it in. Other wise give Omega
a call.

Omega 1000 Juice... | Answered on Apr 26, 2011


There's nothing wrong. These juicers do not eject the pulp and go out of balance very
easily. If you continue to have problems you may have to go for a different type of juicer.
The Hurom or Omega VRT, expensive, look good if you're really into juicing.

Omega 1000 Juice... | Answered on Apr 20, 2011


There are no instructions. Call Omega 1 800 633 33461
for advice. Also new arms on an older juicer may not
be an exact fit so you might have to do a little filing
down on the arm to get it to fit. You can remove the
4 screws on the bottom to separate the base and get
a clearer picture of what you have to do. Basically
you have to pry the base of the arm away and push
up to remove it. If you're not handy you may need
some help cause it gets tricky.

Omega 1000 Juice... | Answered on Feb 09, 2011


First thing to do is call Omega and order a pair
at 1 800 633 3461 and also ask them for tips on
how to remove and install the arm. If your juicer
is older the new arms may not be an exact fit, and
you will have to do a little filing and improvising to
install them. Its helpful to remove the 4 screws on
the bottom to separate the base for better access
and view of the situation.

Omega 1000 Juice... | Answered on Feb 09, 2011


Omega and Acme juicers will vibrate because pulp
is not ejected during juicing. Only suggestion I can
offer is avoid soft produce and feed as slowly and
as evenly as possible. Been using an Acme for 21
years and did notice a duller worn blade does produce
less vibration.

Omega 1000 Juice... | Answered on Feb 09, 2011


Don't think they are an exact fit like the old ones.
Might have to file it down a little and tap it in with
a flat screwdriver. Also once installed if its a little
snug fitting over the cover file the tip down till it
slides over the cover lip easily.

Omega 1000 Juice... | Answered on Feb 09, 2011


What's wrong, you might be able to handle it yourself.
You can also call Omega for help. 1 800 633 3461.

Omega 1000 Juice... | Answered on Feb 09, 2011


If you're talking about the citrus attachment, there may be a
problem with the gearing inside. I have one for my Acme
which I don't use because of it's awkwardness and juice
splattering characteristics. Better off with an inexpensive
citrus juicer and leave the Omega to its carrots and apples.

Omega 1000 Juice... | Answered on Feb 09, 2011


Omega can walk you through it, but have a file handy because the new latch
arms are not a perfect fit for the older juicers. You might want to remove the
4 screws on the bottom to separate the base for better access. If you have
a little mechanical ability it can be done, if not it could get tense.

Omega 1000 Juice... | Answered on Feb 02, 2011


Yours and everyone else's. Best solution is to get a pulp ejecting type juicer.
I have a 21 year old Acme and know how to maintain and adjust it. Even
then I have vibration issues.

Omega 1000 Juice... | Answered on Feb 02, 2011


They all vibrate no matter what you do. Best solution, costly, is to get a pulp ejection
type juicer. Miracle MJ1000 is a nice little juicer for about $130.

Omega 1000 Juice... | Answered on Feb 02, 2011


There may be a reset button on the bottom. Try pushing it.

Omega 1000 Juice... | Answered on Feb 02, 2011

Not finding what you are looking for?
Omega 1000 Juice Extractor Logo

65 questions posted

Ask a Question

Usually answered in minutes!

Top Omega Juicers Experts

Andrew Taylor
Andrew Taylor

Level 3 Expert

29424 Answers

eyecam

Level 2 Expert

96 Answers

Tom Chichester

Level 3 Expert

54386 Answers

Are you an Omega Juicer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Omega Juicers

  • Omega Juicers

Most Popular Question

omega juicer 1000

  • Juicers
Loading...