20 Most Recent Lexmark X6570 InkJet Printer Questions & Answers


Yes, the black cartridge could very well be the issue. In fact, I think it's likely.

Lexmark X6570... | Answered on Jun 03, 2017


Is that a USB connected Lexmark unit?

Lexmark X6570... | Answered on Apr 24, 2017


if you have abby fine reader installed try that software. if not go to start- all programs- lexmark x 6700 series (it depends of the familly class model. mine's a x5100 series)- Lexmark All-In-One Center.

Lexmark X6570... | Answered on Sep 11, 2016


if you don't like to install ocr software to your computer, you can try this free online ocr tool

Lexmark X6570... | Answered on Sep 17, 2015


dear user,

Below link help you to download the driver of printer ..
http://www.siliconguide.com/drivers/device/1912/

Faisal

Lexmark X6570... | Answered on Apr 07, 2015


I have a Lexmark X6570 All In One Wi-Fi model. Just had the problem where I went to print and received an error message saying that the cover was open (when it wasn't). I noticed that the back right hand corner had slightly popped out of place for no apparent reason. Tried to pus it back into place with no luck.

Here's what happened and how to fix it:
There are two plastic hinges at the back of the 6500 series printers that allow the top cover to open for access to the ink cartridge carriage. The lower ends of the hinges are cylindrical shaped and each contains a very stiff steel spring inside. They are designed to prop the cover of the printer up and hold it open when opened. As the plastic material ages, it may weaken and the tension of the internal spring may break the round end of the hinge off. This causes the printer cover to not fully close (even though it may appear so). There is a switch in the main printer body that detects when the top cover it open (even partially), and the printer won't work in this condition.

To fix this, open the top cover and carefully disconnect the 3 wire harnesses and the ribbon cable that run from the top cover to the base of the printer. Then remove the 'paper jam' hatch cover from the back of the printer. There are two phillips screws on the back panel of the pinter (one is located behind the paper jam hatch cover). Remove these screws (they secure the plastic hinges in place). You should now be able to lift the complete top cover/ scanner table assembly off the rest of the printer. Look for a steel spring about 3 inches long...remove this along with the round base of the hinge which may have broken off and remained down inside the printer. Glue this piece back onto the end of the hinge, but leave the spring out. Now reassemble the printer in the reverse order of disassembly and you should be good to go. Note that the top cover or the printer will not stay propped open on it's own with the spring removed, but this is not really an issue.

I am not sure if new replacement hinges are readily available from Lexmark or other sources.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/john_472b46f833fc3109

Lexmark X6570... | Answered on Feb 14, 2015


Hi,
Visit this link for full information of ink change option.
Read More.. support lexmark com and Lexmark Printer Support

Thanks,

Lexmark X6570... | Answered on Aug 27, 2014


Please try to make a Color Copy and let me know if it works Fine?

Lexmark X6570... | Answered on May 14, 2013


In your control panel, devices and printers, click on your printer. you can make it print black from there

Lexmark X6570... | Answered on May 14, 2013


I have WIN8 and using just fine, having issue with colour but other than that everything good

Lexmark X6570... | Answered on May 14, 2013


Please download and install the patch found in this article from the Lexmark website: Registration Reminder Keeps Displaying Every Time You Try to Print.

Lexmark X6570... | Answered on Feb 13, 2013


Are you still able to print/scan/copy? If so, the LCD could be defective. Try to unplug the power of the printer for about 30 seconds then plug it back in.

If it doesn't help, them the LCD could be defective.

Lexmark X6570... | Answered on Dec 10, 2012


I have a Lexmark X6570 All In One Wi-Fi model. Just had the problem where I went to print and received an error message saying that the cover was open (when it wasn't). I noticed that the back right hand corner had slightly popped out of place for no apparent reason. Tried to pus it back into place with no luck.

Here's what happened and how to fix it:
There are two plastic hinges at the back of the 6500 series printers that allow the top cover to open for access to the ink cartridge carriage. The lower ends of the hinges are cylindrical shaped and each contains a very stiff steel spring inside. They are designed to prop the cover of the printer up and hold it open when opened. As the plastic material ages, it may weaken and the tension of the internal spring may break the round end of the hinge off. This causes the printer cover to not fully close (even though it may appear so). There is a switch in the main printer body that detects when the top cover it open (even partially), and the printer won't work in this condition.

To fix this, open the top cover and carefully disconnect the 3 wire harnesses and the ribbon cable that run from the top cover to the base of the printer. Then remove the 'paper jam' hatch cover from the back of the printer. There are two phillips screws on the back panel of the pinter (one is located behind the paper jam hatch cover). Remove these screws (they secure the plastic hinges in place). You should now be able to lift the complete top cover/ scanner table assembly off the rest of the printer. Look for a steel spring about 3 inches long...remove this along with the round base of the hinge which may have broken off and remained down inside the printer. Glue this piece back onto the end of the hinge, but leave the spring out. Now reassemble the printer in the reverse order of disassembly and you should be good to go. Note that the top cover or the printer will not stay propped open on it's own with the spring removed, but this is not really an issue.

I am not sure if new replacement hinges are readily available from Lexmark or other sources.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/john_472b46f833fc3109

Lexmark X6570... | Answered on Oct 03, 2012


look where you load the paper..there should be 1 or 2 freed rollers.
With the unit OFF use a cotton swab dipped in alcahol to clean them. When they get dirty, they slip.
Squipps

Lexmark X6570... | Answered on May 29, 2012

Not finding what you are looking for?
Lexmark X6570 InkJet Printer Logo

188 questions posted

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

X Lexmark

  • X Lexmark

Most Popular Question

install x6570 out disk

  • Office Equipment & Supplies
Loading...