20 Most Recent Panasonic Viera TH-50PX80U Plasma TV Questions & Answers

I locked my panasonic tv and for got the code

Hold the menu button on the remote & the volume down button on the tv simultaneously for 7 to 10 seconds. The tv is reset to original manufacturer settings.

Panasonic Viera... | Answered on Aug 26, 2019

1 Answer

Panasonic plasma tv turns on but no picture or

Same issue with - Panasonic TH-50PX70A , power UP with red standby, then power ON by remote - only Gives GREEN led blinking 35-40 times, followed by solid green led with no no picture no sound.
>> Solution; unplug Plasma from AC 10-15min, then plug in & power on to Red standby led,, At this point - Power ON tv while holding down both -Volume Down and F (function Select) buttons (front panel door) at the same time turns picture ON,all ok.

Panasonic Viera... | Answered on Apr 24, 2018

0 Answers

Panasonic th50px600b has black horizontal

Panasonic Viera... | Posted on Sep 12, 2017 | Be the first to answer

0 Answers

Panasonic plasma tv - black screen on all input

Panasonic Viera... | Posted on Aug 30, 2017 | Be the first to answer

1 Answer

I have a Panasonic 50 inch tv, model# th50px80u. I believe it was struck by lightning, knocking out the main board.

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Panasonic Viera... | Answered on Oct 07, 2016

1 Answer

None of my HDMI ports are working, but my DVD player works

Hi,

I hope I can help with this. It may not be the HDMI port. When you change ports, are you changing the TV video source input on your tv to verify that they work? That is what will need to be done in order test properly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/laura_08254539050d64db

Panasonic Viera... | Answered on Jul 29, 2016

1 Answer

Can't get it out of SAP mode. tried two different remotes. TV doesn't respond.

1. If you're watching TV via a Cable or Satellite box , then the SAP (Secondary Audio Programming) is activated in the box, not the TV. Check with your TV service provider how to activate/deactivate SAP in their box.

2. Only if you're using the TV's own built-in tuner to watch TV (you're changing channels by using the Panasonic remote for CH up/down), then press the SAP button on the Panasonic TV remote to cycle through the SAP options.

Panasonic Viera... | Answered on Jul 14, 2016

1 Answer

Our tv keep disconnectiong from the internet

How far away is the modem? Sometimes you will need to purchase a net gear wi fi extender. I had the same problem or move modem closer. Thank you and leave feedback. Good Luck

Panasonic Viera... | Answered on Jul 12, 2016

1 Answer

On my screen the right hand side has a strip of black so that it looks like it has the wrong format, but cable company has checked it out and says it is a problem with the tv itself.

The TCON Board or the LCD panel is faulty. Can confirm by replacing the TCON board.
If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Panasonic Viera... | Answered on Jun 07, 2016

1 Answer

Why is cable reception snowy and exterior antenna said no signal?

Cable reception is a cable company question. The only reason I say that is because they will do it free for you. It is going to be signal too strong , too weak or it is a bad connector. The antenna is going to depend on a few things. Are you aimed correctly? If this and Omni directional then you need to figure out how far you are from the tower sending the signal. The Omni directional antennas are only good for 50 miles tops and that is some models. You may also need a preamp in line for your signal to be strong enough if you do not have one in line. If you have a lot of runs going on the antenna (several room feeds) then you may also need an adjustable amplifier after the preamp.

Panasonic Viera... | Answered on Feb 09, 2016

1 Answer

When ever the power goes out my 50'' Panasonic tv will not come back on until two days later can you tell me why this is

SOUNDS LIKE POWER-SUPPLY PROBLEM HOW OLD IS THE SET?

Panasonic Viera... | Answered on Jan 21, 2016

0 Answers

Trying to get xfinity x1 remote to run tv, looking for remote code. panasonic remote n2qaybooo221

Panasonic Viera... | Posted on Oct 24, 2015 | Be the first to answer

2 Answers

My screen of th-p50u20k model

pls contact ur near Service center..because only panel replacement can made your tv ok.

Panasonic Viera... | Answered on Sep 04, 2015

1 Answer

13 flash error code----communication error dg board with ic 8001 pesks lite 2. What does that mean and how do you fix it?

bad board and needs to be replaced.

Panasonic Viera... | Answered on Jul 02, 2015

1 Answer

Red power light flashing..no picture

Count the blinks of the led. The number of blinks gives an idea of which board has failed let me know

Panasonic Viera... | Answered on Jun 29, 2015

1 Answer

Reset child lock code on Panasonic TH-50PX80U tv without remote

You can't unlock the child lock without its remote cotnrol.

Panasonic Viera... | Answered on May 06, 2015

1 Answer

TV POWERS ON NO PICTURE

I had the same thing happen to my Samsung 46" led TV. It was a compassitor. We called around to TV repair guys cause we didn't have a lot of money. One of the guys came out and fixed it for $50 on the side.

Panasonic Viera... | Answered on Apr 28, 2015

2 Answers

No picture or sound. the red power light blinks 10 times in a row every few seconds

capasator prob

Panasonic Viera... | Answered on Apr 18, 2015

1 Answer

Panasonic viera 50px80u tv will turn on but no picture. HELP?!?!

If your LCD TV or monitor has stopped working, or is displaying one of the following symptoms, then it's a candidate for some new capacitors
- Flickering screen
- Screen image disappears after several seconds
- Dim screen
- Slow start
- Power LED on, but no picture
- Unusual colors and/or lines
The primary cause of LCD TV and monitor failure is caused by faulty capacitors. You can examine the capacitors in your LCD TV or monitor and actually see if they are bad.
If they appear bulged on top, then they need to be replaced.
New capacitors will solve a host of problems in LCD monitors and TV's and will extend the life of your monitor or TV by several years.
Check the cables, connectors and connections.
Take it to a repair shop.
https://www.youtube.com/watch?v=TR2iWN6b-LY

Hi Josh,
Your TV is 7 years old, so it is not worth spending a lot of money fixing. You could take it to a shop for an estimate.
LCD TV Repair No Power Power Supply Common Symptoms Solutions How to...

Panasonic Viera... | Answered on Mar 04, 2015

1 Answer

I am getting no sound out of my Panasonic Viera TH-50PX80U Plasma TV

Are the speakers' cables connected correctly? (p. 37) Is "Sound Mute" active? (p. 13) Is the volume set to the minimum? Is "Speaker output" set to "Off"? (p. 22) Change "SAP" settings. (p. 16) Check "HDMI 1 in", "HDMI 2 in" or "HDMI 3 in" settings. (p. 22)
Hope this helps, page# refer to your manual.

Panasonic Viera... | Answered on Feb 15, 2015