20 Most Recent Jandy Aqualink Rs4 One Touch Control System Control System Questions & Answers


if using aqua pure check sensor and cell

Jandy Aqualink... | Answered on Dec 05, 2017


turn off then back on if same check salt sensor

Jandy Aqualink... | Answered on Dec 05, 2017


This issue sounds tricky. I recommend you callthe Jandy technical support at 800-822-7933 and they should be able to help youfigure this issue out.

I hope this helps.

Jandy Aqualink... | Answered on Nov 23, 2017


His is not typically a control panel issue but more likely a valve issue.

Your valves are set as follows wih a few minor variations.....
Pool mode- sucks from pool skimmer and or pool vac line and returns water to both the pool and spa.
Spa mode - self contains the spa , meaning water is sucked from the spa and returned only to the spa.
If your spa is draining then most likely one of your electronic valves is failing...most likely it's the return valve so what is happening is the water is sucked from the spa and returned to the pool instead of self containing the spa.
Easy check is to be next to the equip when spa mode is selected and two valves should move and align properly, the return side valve is most likely not moving or it is not moving into the correct position.
The fix is either adjusting the valve acuator or buying a new valve acuator.
Another thing to check is on the main panel circuit board to ensure the return and auction 3 pin plug ins are still connected.

Jandy Aqualink... | Answered on Nov 22, 2017


You or some one else may have assigned the AUX 3,4 to "dimmer" in system settings. Check the setting and make sure it is not set for color lights as well.

Jandy Aqualink... | Answered on Dec 03, 2016


it may be a relay check for power at the blower if power replace blower if not replace relay

Jandy Aqualink... | Answered on Jun 08, 2016


check for shorted wires going to 4 pin red plug or cut wires

Jandy Aqualink... | Answered on May 01, 2016


reset or shut system down and reboot

Jandy Aqualink... | Answered on Apr 29, 2016


look on inside of door schematic

Jandy Aqualink... | Answered on Apr 29, 2016


reset on side

Jandy Aqualink... | Answered on Apr 29, 2016


check for cut wires or shorted wires

Jandy Aqualink... | Answered on Apr 29, 2016


turn all off then turn back on

Jandy Aqualink... | Answered on Apr 29, 2016


check 4 pin red connector if plugged in check wire

Jandy Aqualink... | Answered on Apr 23, 2016


check sensor for aqua pure

Jandy Aqualink... | Answered on Apr 16, 2016


check the red 4 pin plug could be loose

Jandy Aqualink... | Answered on Apr 16, 2016


clean sensor and cell

Jandy Aqualink... | Answered on Mar 05, 2016


bad light relay what ever aux it is replace it it is stuck on you can turn off breaker for light in temp fix

Jandy Aqualink... | Answered on Mar 05, 2016


contact jandy they will send you a PDF of programming

Jandy Aqualink... | Answered on Mar 05, 2016


go to system set up go to programs and edit or remove

Jandy Aqualink... | Answered on Mar 05, 2016

Not finding what you are looking for?
Jandy Aqualink Rs4 One Touch Control System Control System Logo

193 questions posted

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10371 Answers

Bill Jordan

Level 2 Expert

375 Answers

Steve Slater

Level 2 Expert

72 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jandy Pool & Spa

  • Jandy Pool & Spa

Most Popular Question

aqualink rs says check aqua pure no flow

  • Pool & Spa
Loading...