Question about NEC VT595 LCD Projector

2 Answers

VT595 LCD Won't come on. Power light orange Status red Blincks Once every sec or so.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 76 Answers

If the lamp life has exceded its safe working limit, it will probably go into a permanent standby mode, I used to have an NEC MT830, I had to hold down the off button for 20 seconds to reset the lamp life, maybe it will be something similar. If you have your manual, it may give instructions, if not there will be a downloadable manual on the NEC website.

Good luck

Posted on Aug 10, 2011

Ad

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is a plastic piece that breaks off of the lid cover. If it's not there anymore, the projector won't turn on (that piece is the projector's way of telling that the cover is on, it pushes a sensor that tells it so). I myself am trying to find a replacement lid cover. No luck yet.

Posted on May 23, 2012

  • Annie McCall May 23, 2012

    There is a plastic piece that breaks off of the lid cover. If it's not there anymore, the projector won't turn on (that piece is the projector's way of telling that the cover is on, it pushes a sensor that tells it so). I myself am trying to find a replacement lid cover. No luck yet.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

NEC lt240 lamp light stays off and power light is orange, no Image


COULD HAVE HOUR COUNT LAMP LOCKUP YOU WILL NEED TO RESET HOUR COUNTER BY USING BUTTON CONFIG AND MAINS.

john

www.jvsvisual.com

Apr 15, 2013 | NEC LT 240 Multimedia Projector

1 Answer

Having a problem getting past the red blinking status and orange blinking when trying to start up a NEC VT595 projector. This is after installing a new bulb.


I have had the same problem with my NEC VT695, however, while trying to repair it, I actually broke off two pieces, first the arm that is attached to the lamp cover that depresses the button, and then the actual button itself. Does anyone know any way to bypass this need to have the lamp cover seated 'properly'?

Jul 13, 2011 | NEC VT595 LCD Projector

1 Answer

My NEC vt 595 was working fine last night and today i went to turn it on the status and power light started flashing red and orange and there is no picture


if Power is flashing orange - then it's cooling down

if Status is flashing red - then there are 4 flash combinations.
1 cycle (0.5sec On, 2.5sec Off) lamp cover or housing error
2 cycle (0.5sec On, 0.5sec Off) temperature error
4 cycle (0.5sec On, 0.5sec Off) fan(s) error
6 cycle (0.5sec On, 0.5sec Off) lamp error

Which is your condition?

Mar 18, 2011 | NEC VT595 LCD Projector

1 Answer

Thank you kindly in advance for any suggestions on the following issue with the NEC VT595. It will stay on for about 20 minutes and then cut out/off. Then I get the six interval flashing Power and Status...


Hi,
There is a good chance that the problem may due to overheating. The status light would be blinking when it turns off.
Remember to disconnect the mains supply before working on the projector..
You should ensure that there is adequate ventilation and air flow around the projector, and that it is not in a very hot or humid room. Clean the air filters, using a vacuum cleaner. You should not need to remove the filter to clean it. Do not wash the internal sponge filter. It's better to replace it with a new one. The air filters are located on the side of the projector nearest the lens, one at the front and one at the rear.

Feb 19, 2011 | NEC VT595 LCD Projector

4 Answers

NEC VT595 Projector - Status light blinks red constantly


We had this same problem. In our case it turned out that a little bit of plastic broke off of a tab on the inside of the plastic lamp cover. Without that piece it was not pressing against the sensor that tells the projector that the lamp cover is closed. Without that, it doesn't start. We got it working again by drilling a little hole and sticking a screw through that spot to replace the missing plastic, but I'd rather replace the cover if I could. Really dumb that a little piece of plastic can mess up thousands of dollars worth of equipment (Smartboard 2000i).

May 26, 2010 | NEC VT595 LCD Projector

2 Answers

Lamp light stays solid red . i already replaced bulb. any solutions?


Check your owners manual for diagnostics. You can find all documentation for your VT595/695 projector on the NEC support site.

The users guide indicates that the lamp timer needs to be reset. Instructions can be found on page 49 of the users guide.

Press and hold the HELP button on the remote control for 10 seconds to reset the timer.

Feb 05, 2010 | NEC VT595 LCD Projector

1 Answer

My nec vt595 wont start up the status light is flashing orange


The only time the "status" light will be orange is when you accidently press the cabinet button and the cabinet is locked.

However, if the "power" light is blinking orange it means that the projector is cooling down and you need to wait a few minutes.

Jan 03, 2010 | NEC Computers & Internet

3 Answers

I have replaced bulbs in 3 different types of NEC projectors: a silver, older model thta uses a VT60LP bulb, model VT595 and VT470. The lamp will still not work - the power and status light just continue...


I had the same issue, what I figured out was that I never removed the lamp door correctly, causing a small plastic piece to break off. To see if this is also your problem, inspect the back of the lamp door, top right corner, if it seems a rectangular plastic piece is missing, thats the problem. It presses in a small button nearby the lamp to let the projector know it's safe to power on.

I've attached an image to help out.ea22ca6.gif

Sep 01, 2009 | NEC VT695 LCD Projector

2 Answers

NEC VT 595 wont turn on. Just red blinking light


I had this same problem with 2 NEC VT595 projectors. My problem was that there was a broken "tab" on the lamp cover (the plastic cover that slides in place over the lamp) that is supposed to depress a switch which insures the lamp cover is in place before operating the projector. The tab was broken in half and not making the connection there for causing the blinking status light (.5 sec on, 2.5 sec off) indicating a lamp housing or cover error.

May 28, 2009 | NEC VT595 LCD Projector

Not finding what you are looking for?
NEC VT595 LCD Projector Logo

725 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2239 Answers

The Knight
The Knight

Level 3 Expert

76177 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a NEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...