Question about GE Profile JTP18 Electric Single Oven

4 Answers

DOOR Locked Flashing

After a 4 hour cleaning the DOOR LOCKED keeps flashing and the locking motor keeps running - constantly cycling locking and unlocking the door - but the DOORLOCKED Flashing does not change.

Posted by on

  • 4 more comments 
  • dennis1225 Sep 06, 2008

    is this the same swtich that controls the light? This seems fine.

  • dennis1225 Sep 07, 2008

    Where is the interlock switch - is it the same as the light switch on the frame that is closed by the door when shut?

  • dennis1225 Sep 07, 2008

    Fuses? Do I need to take the control panel off to get to fuses?

  • dennis1225 Sep 07, 2008

    micromaster - could a blown fuse cause the locking motor to cycle continuously? Seems like it would more likely be a sensor that looks for the door to be in the latched position.

  • dennis1225 Sep 07, 2008

    The link you provided does not provide any information on my problem.

    Where are the fuses?


  • dennis1225 Sep 14, 2008

    DO I need to take the control panel off to check for a malfunction latch? If the light goes off when the door switch is depressed does that mean that the door switch is working properly or are there multiple functions of the door switch and I need to remove it to see if it is failing even if the light is turning off?

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where are the fuses located in the oven? I do not have a self cleaning oven and it keeps saying locked door and kicks off and will not cook again till it cools off. This happens everytime I use the oven.

Posted on Nov 21, 2008

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,952 Answers

Operating Check that door switch is completely closed. Check latch, solenoid, and actuation switch for electrical or mechanical malfunction.
Check wiring and test operation of door lock switch

Posted on Sep 14, 2008

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,614 Answers

Check the interlock switch, can be some object has stuck to it...

Posted on Sep 06, 2008

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

Hello dennis, this is what i found in the manual;

“LOCK DOOR” flashes The self-clean cycle has
in the display been selected but the
door is not closed.•

solution: close the oven door

LOCKED DOOR light is on when you want to cook.

The oven door is locked because the temperature inside the oven has not dropped below the locking temperature.

solution:• Press the CLEAR/OFF pad. Allow the oven to cool.


tnx 4 using fixya,

drcool

Posted on Sep 14, 2008

  • francis rivero Sep 14, 2008

    sorry, wrong arrangement oft he words for the first guide

    here is the correct one.

    LOCK DOOR flashes in the display

    the self clean cycle has been selected but the door is not closed

    solution: close the oven door.

    tnx again..
    drcool


×

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does error code F-90 mean on a Kenmore delf cleaning wall oven


The F90 error code indicates that the door unlock time exceeded. This will happen if the lock is in the locked position with the oven door open or if the lock motor fails. Have someone hold in the oven door light switch while you set the control up for the self-cleaning cycle. Let the self-cleaning cycle run for only 4-5 minutes then press stop/cancel. This should allow the lock assembly to reset & retract the door lock back into the unlocked position.

You can also try resetting the appliance by disconnecting it from the outlet or switch off the circuit breaker for 20-30 minutes. Once power is restored run a test cycle. If this does not work I suspect a door lock assembly failure. This type of diagnosing will require accessing the lock assembly & using a volt/ohm meter for testing

Nov 03, 2016 | Kenmore Ovens

1 Answer

How do you keep the door locked so you can use t self cleaning feature


Good Morning Friend,

I understand you want to know how to keep the door locked on your Frigidaire oven, model# FEB24S2AS, so you can use the self-clean feature. The "Door Locked" light will flash until the door locks when the self-clean cycle is in use. It glows constantly after the door locks. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 28, 2014 | Frigidaire FEB24S2AS / FEB24S2AB Electric...

1 Answer

How do i operate the self cleaning function


Hello - Before using the self-cleaning cycle of the appliance, remove the broiler pan and any utensils stored in the appliance. Also remove any excess spillovers in the oven cavity. Allow the oven to cool before cleaning. During the self-cleaning cycle, the outside of the wall oven can become very hot to the touch.

Typically to set the controls for a self-clean the first step is to confirm that the clock shows the correct time of the day. Press CLEAN. "---" appears in the display. Press the UP ARROW or DOWN ARROW once. "3:00" appears in the display for a 3 hour cycle. To change to a 2 hour cycle press DOWN ARROW"2:00" appears in the display. As soon as the controls are set, the motor drive lock will begin to close automatically and the "LOCK" indicator light will flash. DO NOT open the oven door while the light is flashing (it takes about 15 seconds for the over door to lock). "CLn" will appear in the display during the Self-Clean cycle and the "LOCK" light will glow until the Self-Cleaning cycle is complete or cancelled and the oven temperature has cooled.

When the Self-Clean cycle has completed, the time of the day or "End" will appear in the display window and the "Clean" and "LOCK" light will continue to glow. Once the over has cooled down for about 1 HOUR and the "LOCK" light has gone out, the oven door can be opened. If "End" is the display and the Clean indicator light remains ON, press CLEAR/OFF. The time of the day will appear in the display.

If it becomes necessary to stop or interrupt a Self-Cleaning cycle, press CLEAR/OFF. Once the oven has cooled down for about 1 HOUR and the "LOCK" light has gone out, the oven door can be opened. Restart the Self-Clean cycle once all conditions have been corrected.

Oct 19, 2012 | Frigidaire GLEB27S7A Electric Single Oven

1 Answer

Locked after self clean cycle


you may have a bad door lock . in this case replace. but first reinstall the door and run a new clean cycle and see if it unlocks .. mm

Jul 14, 2010 | GE JKP45 Electric Double Oven

1 Answer

F90 code flashing and i cant reset it


F90 Maximum oven door unlock time exceeded.
F91 Maximum oven door unlock attempts exceeded.
F92 Maximum oven door open time exceeded.
F93 Maximum oven door lock time exceeded.
F94 Maximum oven door lock attempts exceeded.


1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.

2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.

3. (F90, 91, 92, 93 & 94) Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.

4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, replace Lock Motor Assembly.

5. (F90, 91, 92, 93 & 94) Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly.

6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.

7. If all situations above do not solve problem, replace EOC.


F90 is a door lock code, Try this...
unplug the range.
wait 1 minute.
turn the range back on,
then while holding in on the oven door.
start another self clean.
wait 2 minutes.
then cancel the self clean.

do not release the door until the door lock light goes out.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question@#$%

Jul 07, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

2 Answers

Self cleaning oven won't unlock after cycle is complete


Unplug it for about 30 minutes, plug it back in and see if it unlocks. If not, then the latch, interlocking microswitch or control board is faulty. Also look for any bad connections (make suer the power is off before you start wiggling connections).

May 21, 2009 | Ovens

13 Answers

Flashing locking door light


Re : Within the electrical enclosure exposed by removing the control panel, Look for a small silver and black device with 2 wires attached to the back.

That cames from an old thread and is a generic explanation of how it works. Here original reference
GE Profile Electric.

There is no electrical cylinder because the solution was referring to a different model and a different problem. In case linked above the door was locked, in your case door is clicking continuously, showing that there is a contact or a faulty door lock motor control.

If I was doing the repair I would start reading voltages on lock motor motor harness with motor wiring cut, this will tell you if contact is inside lock motor assembly or on control. The test can be done either from control side (easier access) or from lock motor, after disconnecting the harness.
If the control actuator keeps turning on and off , then replace the box in there, otherwise work on wiring harness and on lock motor.

This is not an easier repair, and tests with live power in there may be riskyd if you have not enough experience. If you are a beginner just inspect wiring with power off first, then replace control, and if that does not fix the problem replace wiring harness.

Here parts that must be tested, and relative diagrams:

LOCK MOTOR WIRE HARNESS (LCK MTR HARN) connects to part 999 on diagram.



LIMIT SWITCH(LOCK)
Part 158 on diagram.

ea2994c.gif

If problem is not in control or wiring harness, then check if there is a contact inside door lock assembly or on LOCK MOTOR connectors. If two connectors on picture below are making contact, that is the problem:

ba71f6f.gif

As a matter of principle , do not forget to leave feedback, or you may end up rewarding the person that copied and pasted a solution for the wrong problem.

Thanks, and thanks for asking Fixya.

Ginko.







Sonce the proble



May 16, 2009 | GE Profile JKP56 Electric Double Oven

3 Answers

"Door Locked" flashing on GE Oven JTP15 - can't unlock


The problem may very well be in one of the micro switches on the self cleaning motor bracket. These switches control the electrical flow to the heating elements. In the owners manual there is/should be a chart that lists the unlock and safety combinations. This would be your best source of information.

Jan 20, 2008 | GE Profile JTP18 Electric Single Oven

1 Answer

Door Keeps Locking and Unlocking after Power Outage


Located the switch - resetting fixed my stove as well.

Dec 17, 2007 | GE Profile JTP18 Electric Single Oven

10 Answers

Our GE Profile JTP18 keeps flashing "door lock" since we ran a self clean


most of the time a simple fix.... http://www.geappliances.com/search/fast/infobase/10004586.htm
you have to trick the door lock mech into cycling through the cleaning process (takes about 20 seconds)
Print Range - “LOCKED DOOR” flashes in the display

If “LOCKED DOOR” is flashing in the display of your range or oven, and the self-clean cycle has not been selected, follow the steps below to reset your control:

Motorized Switch
    1. With the door open, locate the door jamb switch on the face of the oven. It will look like a small black post or dowel.
    2. Push it in until the oven cavity light goes off, indicating that the oven believes the door is closed.
    3. While you hold the door jamb switch in this position, complete the following steps.
    4. Press the Clean pad, wait 10 seconds.
    5. When the cycle initiates, press the clear/off or cancel pad immediately to cancel it.
    6. Wait 10 seconds for the display to clear.
    7. The door should unlock and there should not be a need for service.
Manual Switch
    1. Press the Clean pad.
    2. Close the door.
    3. Slide the latch to lock the door.
    4. Hit the cancel button immediately.
    5. Unlock the door.
If the above does not correct the situation, a service technician will need to check your cooking product. To obtain in or out of warranty repair on Major Appliances, you may call 1-800-GE-CARES (800-432-2737) or schedule service online.

Sep 14, 2007 | GE Profile JTP18 Electric Single Oven

Not finding what you are looking for?
GE Profile JTP18 Electric Single Oven Logo

1,758 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

9179 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...