Question about Acu-Rite AcuRite 00592A2 Wireless Humidity and Temperature Meter

1 Answer

I have an ACURITE 00590A1-RX. My time is off by 10 minutes. i don't have my manual and would like to know how to reset it. If possible, tell me how to download a manual.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

From the manual, such as it is:

Set the Time Manually:
If you want to set your alarm clock a little ahead or if the unit ever loses time for any reason, the time can be set manually by following these steps.
1) Press and hold the "CH./SET" button for seven seconds to begin the manual time set mode. (2 BEEPS) The hour will flash on and off.
2) Adjust each setting by pressing the "+" or "-" buttons. Confirm and move on to the next setting by pressing the "CH./SET" button.
MANUAL TIME ADJUST SEQUENCE: hour, minute, year, month, date

This works for me. You have to be sure to keep pressing the CH/SET button for the full seven seconds -- the first beep the the clock gives you will only allow you to set the time zone and DST function.

Posted on Nov 17, 2013

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Marcus Wirkus

  • 1 Answer

SOURCE: I have an Acurite 822-RX thermometer that shows HH

HH means it is showing the high temperature you (most likely accidentally) set with the MAX MIN / + button, which is easy to do when setting the clock. Just press that button again until the reading appears.

Posted on Dec 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have an Acurite 822-RX thermometer that shows HH as the outdoor temp, even after replacing the batteries in both the base and remote units. How can it be fixed or reset?


Usually those symbols mean your out of range of the instruments range . Do you have the sensor in direct sun light ? There may also be a defect I would try to contact them

Mar 10, 2015 | Measuring Tools & Sensors

1 Answer

How to reset my Acurite 1099rx after replacing battery


http://www.acurite.com/advancedsearch/result/?q=1099RX

There is no reset button, installing new batteries causes the sensor to reset itself.

Try removing and re-installing the batteries.

Good luck,
Steve

Jan 15, 2013 | Measuring Tools & Sensors

1 Answer

Car started and stalled, 3 times and then will not start at all. ? possible security system but do not know how to reset at home, or do I have it towed to a dodge dealership?


Make the FixYa experience better for everyone by voting.

Hi,

My name is Ben and I'm your guru, i.e., mentor, an influential teacher or popular expert: a management guru. - origin from Sanskrit, 'weighty, grave' for today.

As you evaluate my advise. solutions and suggestions, there are a few things you must keep in mind:

• I did not diagnose your problem and am therefore only able to evaluate what you tell me. For example, if you ask me a fuse location, that doesn't mean that I can tell you the reason why the fuse blew. I can only react to the information that you provide. So please judge my suggestions accordingly.
• A thorough diagnostic approach involves the use of technical equipment, such as voltage meters. scanning equipment and other sophisticated devices. Diagnostic tools can be borrowed from AutoZone for FREE:
• Lastly, fixing one problem can very easily reveal a problem with something that you might consider unrelated. If that happens, you might want to view me as being incompetent.

Your description of the problem: car started and stalled, 3 times and then will not start at all. ? possible security system but do not know how to reset at home, or do I have it towed to a dodge dealership?

First: You don't indicate any diagnostic tests to date. A dealer or your local mechanic will charge $100-$200 to perform a diagnostic scan. However, AutoZone will provide a thorough scan for FREE or you can buy a code reader for about $30. Anyone who tells you that a modern vehicle can be diagnosed without a scanner with the problems you have set forth is merely guessing. You car has a computer and memory and probably knows exactly what the problem is. That on-board computer is just waiting for you to ask, "What's wrong".

However, if you believe that your problem is with the security system, read the following carefully.

Please don't even think about trying to disarm your anti-theft system because there is an easier solution. I'm assuming that you don't have the full Shop Service Manual. If you do, then you know that a shop manual costs at least $100.

So why did I say: Don't even think about it? Your anti-theft device is capable of causing problems that you don't want to deal with. If you have the dealer do the job, the cost can be prohibitive. The anti-theft device tells the on-board computer to shut off the fuel flow and to disengage the starter circuitry.

SOLUTION: Go on eBay and buy an anti-theft bypass module for $10-$20 depending on the year and make of your vehicle.

All the best

Ben

Sep 12, 2011 | 2000 Dodge Intrepid

1 Answer

Error 5200 or PO8?


1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 12, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

Removed battery while replacing thermostat in my Lexus RX 330. After completion I started engine to find that my check engine light was on along with my VSC and Trac Off. Engine is also not idling...


Most vehicles now-a-days come equip with an on board computer. This computer stores and records several statistics about the operation, condition, and overall health of the vehicle. When you remove the battery, this computer is reset. The results can be a loss of oil level records (when it was changed, when it needs to be changed) tire pressure defaults, etc. In addition, as the vehicle is driven, the computer makes adjustments to things like fuel injection on the engine and other active tasks to improve mileage or performance.

When you reset the computer, it reset all the data along with it. This may cause the check engine light to come on as the car no longer knows the status of certain frequently changed or replaced parts. Your traction was probably turned off either as a response to this or because it was the default for the vehicle; seek out the manual for your vehicle and it should tell you how to re-enable this feature. Lastly, the idle may seem rough because you reset the computer and it no longer provides a tailored level of fuel injection. Over time, this issue should resolve its self as the computer learns.

May 16, 2011 | 2004 Lexus RX 330

1 Answer

I have an Acurite 822-RX thermometer that shows HH as the outdoor temp, even after replacing the batteries in both the base and remote units. How can it be fixed or reset?


HH means it is showing the high temperature you (most likely accidentally) set with the MAX MIN / + button, which is easy to do when setting the clock. Just press that button again until the reading appears.

Jan 15, 2011 | Acu-Rite Acurite Wireless Weather...

1 Answer

Acurite 1097-rx will not display outside temp or humidity. new batteries. Inside functions normal.


I had same problem. Take all batteries out of both units. Put the batteries in the remote sensor FIRST. Then put batteries in the main unit. Within five minutes, they will link up. Problem solved!

Feb 23, 2010 | Acu-Rite Audio Players & Recorders

Not finding what you are looking for?
Acu-Rite AcuRite 00592A2 Wireless Humidity and Temperature Meter Logo

1,241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acu-Rite Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

18110 Answers

David Gust

Level 2 Expert

173 Answers

ray gallant
ray gallant

Level 3 Expert

64733 Answers

Are you an Acu-Rite Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...