Question about Mitsubishi MS12TN Air Conditioner

Open Question

No dc power from outside unit to inside unit.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Outside unit aircondition is working but inside unit is not blowing air

I had a similar problem on mine but the other way round. It turned out the PCB (circuit board) was busted on the outside so they werent communicating. Inside operated but outside didnt. If you have any electrical test equipment, disconnect com line (between outside and inside) there should be a varying DC voltage at each end. If its 0V then PCB is dead. Could also be the fan motor has packed up. Theres some places to start anyway.

Sep 02, 2014 | Carrier Heating & Cooling

1 Answer

Power supply blown

You can check your AC adapter by voltmetter in Dc mode, one probe touches inside the plug, other probe touches outside, it should have dc reading if the ac adapter is working.
Your plug is slightly burnt, indicating that the DC jack is broken or loose.
Most DC jack can be replaced if you know how to solder, it costs only under $5.

I believe your DC jack needed to replace and a repair guy might charge you over $150 to replace a $3 part. You should do it yourself if you have a skill to take a laptop apart.

Car Tuning

May 24, 2012 | Computers & Internet

1 Answer

I have a hp pavilion dv7 and the power socket has come a lose i need to know which wire goes where.....

The DC Power Jack that the AC adapter (Charger) plugs into?

Look into the DC Power Jack with a magnifying glass and light you'll see it's a center pin surrounded by a barrel. Barrel has an inside and an outside.

1) Center pin. Gold and buried down in the plastic. Connected to WHITE wire at motherboard connector.

2) Inside barrel has 4 Brass fingers.
Orient the laptop so the LED is at 12 o'clock and you'll see fingers at 12, 3, 6 and 9 o'clock.

These fingers carry the + 19 volt power to computer.
The ones at 6 and 9 o'clock do, Noon and 3 are not connected.
+19 Volt power arrives at motherboard connector on RED wire.

3. Outside barrel has six brass fingers, at 2, 3, 4, 8, 9 and 10 o'clock.
2, 3, and 4 are not used,
2, 8, 9 and 10 are the power return (common, or ground) to computer.
It arrives at motherboard on BLACK wire.

4. LED is connected to YELLOW wire and controlled by computer.
Other side of LED is jumpered to a Black wire,(Ground), outside barrel 8, 9, and 10 o'clock.

From > analog posted in an HP Support Forum.

Nov 12, 2010 | HP Pavilion dv1000 Notebook

1 Answer

When we start it every other step stalls for a few swconds

Unplug unit pull right side cover then reconnect dc power cable unit. their is a circuit board with 3 lights :
1) Power should be lit as soon as you plug the DC power cable
2) Relay Check silver tab #4 labeled +/wht and Tab #5 Gnd/blk with a meter check DC voltage between15v and 17v if not in this range replace relay board.
3)Field this a signal is sent from the alternator,when stepping it will make the light flicker and send this signal to the upper console.
A) check alternator for black powder inside and or near the outside casing.The brushes maybe bad and can be replaced.

Jan 29, 2010 | Stairmaster Stepmill 7000 Pt

2 Answers

How many volts does a HP Pavillion TX1410 adaptor has?

Please look carefully at the unit, the ratings are on the outside of it.

Oct 21, 2009 | HP Pavillion ZV6000 Notebook

1 Answer

Outside unit will not start...while inside unit blows warm air

probably a.c. was left with out a gas,and compressor will not start and there is no cooling.

Jul 04, 2009 | Heating & Cooling

1 Answer

Hey i want to know whether fridge requires DC power supply or AC power supply

DC applied to any standard refrigerator would quickly damage the compressor motor and any fans present since these are all AC only motors.
Some (probably no longer produced) units used DC in their operation; - Peltier Efffect units that used a semiconductor device that acts as a 'heat pump,' removing heat from inside the cabinet and dissipating it outside. - A new type of compressor that hummed like a low frequency speaker and surely used DC in the generation of the driving signal.
The first proved to be less efficient than our near century old compressor system and the odd low frequency noise produced by the second could not be contained adequately for home use. 

Dec 10, 2008 | Whirlpool GS6NBEXR Side by Side...

1 Answer

Outside unit not working

If the heating and cooling is working O.K. and maintaining the proper temperatures it is possible that your outside unit is in its off cycle. If the inside unit is running and the outside unit is not with an elevated temperature inside check the power supply to the outside unit. Most units have a disconnect located near them. Check the disconnect and make sure it is set to the on position. Listen for a hum noise at the outside unit which could indicate that the control power is being supplied to the contactor.

Jun 15, 2008 | Samsung AS18A6RB Air Conditioner

2 Answers

Adapter plug size

Wal-Mart ectronics dept. has an "Universal DC Adapter Kit" it will have various size adapter plugs and a variable setting to adjust DC Voltage. It also should have a switch to set the polarity. I used mine to power several different devices. It was well worth the money I spent as opposed to buying a actual DC Adapter. Subsequently, the kit from Wal-Mart was far cheaper than the real deal.

Albuquerque, NM

Aug 28, 2007 | RCA DRC620N Portable DVD Player

Not finding what you are looking for?
Mitsubishi MS12TN Air Conditioner Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Heating & Cooling Experts


Level 3 Expert

8546 Answers

Stuart Slabber

Level 1 Expert

25 Answers


Level 3 Expert

85222 Answers

Are you a Mitsubishi Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides