Question about Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

How do you take inside cover off - Weiser Lock POWERBOLT ELEC DEADBOLT

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 963 Answers

The Weiser brand and Kwikset brand Powerbolt are identical, so these instructions will work just fine for you:

http://www.kwikset.com/Customer-Support/Product-FAQs/Faq/50160000000HhhEAAS.aspx

Good luck--and please provide feedback if this helps!

Posted on Sep 14, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tighten kwikset #991LL


Remove inside lever by loosening the setscrew and pulling. Carefully pry off the inside cover. Make sure both screws are tight. Replace inside lever. With door unlocked, the outside lever can be removed in the same way as the inside. All that is necessary though is to be sure the setscrew on the outer lever is tight. Check to be sure the lock is tight and operating correctly before closing the door and locking it.

The deadbolt inside turnbutton is held on with a small setscrew. Remove it and the inside cover. Be sure the screws under the cover are tight. Check the lock operation, replace cover and turnbutton.

Jul 07, 2014 | Kwikset 991ll 15 Smt Cp Lido Entry Lever...

1 Answer

How to replace passenger side mirror ?


You will have to remove the inside cover. After removing the inside cover then use a deep socket to take off the nuts holding the old mirror on. Then unplug the wires. As you put the new mirror on make sure it is square and streight. Before putting the inside cover back on make sure the mirror is working correctly. Then fasten up the cover and clean off the finger prints.

Jul 03, 2014 | Buick Rendezvous Cars & Trucks

1 Answer

My seagate external hard drive cable cannot be connected to the external hard drive. the mechanism to hold the cable has loosen and is now inside the hard drive. What can I do?


You can unplug all wires from it.
Remove the screws which hold the chassis (cover) and remove the cover to access the hard drive inside.
Once the cover is off, you can see the connector inside and repair it back the way it was.
Replace the cover and screws and you are done.

Apr 15, 2011 | Seagate Computers & Internet

2 Answers

Error message top cover open


When the printer is used often, and ink and dust accumulate inside, the detector switch will sometimes get stuck and won't be depressed by the cover correctly. Open the cover and look right next to the sticker. There is a small rectangular hole with the switch. Use a very thin tool like a small screwdriver or paperclip bent open to push the switch inside the hole to the back of the printer. Do NOT push it just down! You *must* move the switch away from you. Hold the switch in this position and close the cover. Carefully pull out your tool from the gap.

Jan 28, 2010 | HP DeskJet 5652 InkJet Printer

1 Answer

How do you get lese cover off?


most likley the lense cover is not just a cover but a unit and order to remove it there would be bolts inside of trunk

Jan 01, 2010 | 2008 Chevrolet Impala

1 Answer

PROBLEMS WHITH THE TRANSMISSION CONTROL SOLENIOD


===shift interlock solenoid--Inside the steering column near the ignition switch

===1-2 shift solenoid valve--Inside the automatic transaxle
to remove it :
  1. Remove the case side cover. Refer to Case Side Cover Replacement.
  2. Disconnect the transaxle wiring harness.
  3. Remove the 1-2 shift solenoid (315A).
2-3 shift solenoid valve--Inside the automatic transaxle
to remove it;
  1. Remove the case side cover. Refer to Case Side Cover Replacement.
  2. Disconnect the transaxle wiring harness.
  3. Remove the 2-3 shift solenoid (315B).
==the torque converter solenoid--inside tranny too

good luck,let me know

Jun 04, 2009 | 2000 Pontiac Montana

1 Answer

Cassette compartment cover blocked


have you try to open it and see for any loose spring parts.?

thanks

Apr 23, 2008 | Cameras

1 Answer

MP600 - Says inside cover is open - but it's not!


This is a hardware problem nothing to do with software; somewhere inside the printer a cover is not closed correctly.

Jan 24, 2008 | Canon Pixma MP500 All-In-One InkJet...

1 Answer

Dirt on the inside screen


Usually the best way is to remove the top back cover and clean the inside of the screen with a clean, dry cloth, but be careful because the mirror is mounted on the inside of the top back cover.

Jun 21, 2007 | Panasonic PT-51HX41 51" Rear Projection...

Not finding what you are looking for?
Weiser Lock POWERBOLT ELEC DEADBOLT Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Azam Ali

Level 1 Expert

31 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...