Question about Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

Reset new codes and old existing codes won't erase,the original code from last year still works, even after installing 2 new codes

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 963 Answers

Here's the link to the online instructions:
http://www.weiserlock.com/PDFS/instructions/Electronics/Powerbolt.pdf
Programming instructions are on page 6. Notice that allowing too much time between inputs will be a problem.
If you cannot successfully override your existing codes, contact Weiserlock Customer service:
http://www.weiserlock.com/CustomerService/ProductSupport/SupportContact.aspx
A note about PDF files: You will need adobe Reader or equivalent installed if you are unable to view the instructions. http://get.adobe.com/reader/
Good luck!

Posted on Nov 06, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air pump not working and red light stays on reset. Is the pump bad or electrical problem?


It is a toy spa after all, not really meant to last long.
According to Intex, your fault code is due to low or no water flow. Most common problem that we see is bad filter. You either need to clean, soak, or just replace them! Because they are so small, I wouldn't even bother with cleaning them, just have a few handy, and just install new ones.

Apr 12, 2015 | Pool & Spa

1 Answer

Low toner warning light always blinking


maybe the toner t1810c is not original...try this code turn off the machine then press 0 and 2 at the same time then a value of 3 digit will appper just press start button...dont turn off the power other wise this toner warning will show again...repeat this procedure the next time u off then on the machine...hope this can help...

Apr 05, 2013 | Office Equipment & Supplies

1 Answer

I changed a honeywell thermo last night. I'm


check your transformer some of them have a little reset button on the side if it arched it could of tripped it.if there is no reset make sure you have 24v coming into thermostat.

Apr 22, 2012 | Honeywell Heating & Cooling

1 Answer

I'm getting error code 51030


Hello Carole,

"Power cycle" your router and modem. To do this, unplug both the modem and the router from the power outlet. Wait a few minutes, and plug the modem back in. Wait a couple of minutes for the modem to initialize, then plug in the router. Try to connect the Wii online and test for proper response.

If that doesn't work, erase your old connection settings on the Wii and set up a new one, as your router's settings may have changed since you last connected.

If that still won't work, reset your router so it will go back to factory settings. To do that, look for the reset button locatd at the back of your router. Use a pin to press and hold it for 10 seconds.



Thanks for using Fixya!
You can rate my answer if you appreciate it.

-damneddle

Oct 10, 2011 | Nintendo Wii Console

4 Answers

What is master reset code of nokia n97


default lock code for nokia N97 is 12345.

Sep 14, 2011 | Nokia N97 Cell Phone

1 Answer

My external mounted pad lights up, but won't accept the new code after erasing all existing codes. the drive unit lights, the light bulb works, the led turns on and flashes, but the new code will not...


Make sure you are doing it like this.

Locate the smart/learn button on the rear of the motor unit near where all those white wires go. Press and immediately release this and then walk over to the keypad and key in any 4 digit code you like and press enter.


nm0hapqiutzxjjkaaaaaaelftksuqmcc

Aug 30, 2011 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

How do I clear (erase) all codes from my Weiser Powerbolt 1000 in order to start with fresh entries? Adding new codes does NOT override/delete old existing codes as page 7 of my manual indicates. I now...


How do I change the access code (and delete my old code) on my Powerbolt 1000?
The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.

pb1000programbutton.jpg

  1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.
  2. Press the PROGRAM button twice, enter the same new code and then press the LOCK button once.
  3. Press the PROGRAM button three times, enter the same new code and then press LOCK once.

If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour. After the hour has passed, you may re-enter the batteries.



United States of America Customer Service Contact Information
Call Us Toll Free: 800-422-4278 (Mon-Fri, 6:00am - 4:30pm PST)


http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

Good luck, Elizabeth!


Jul 26, 2011 | Weiser Lock Powerbolt 1000 Lock

1 Answer

I got a 2000 Ford Explore that I got about 5 months ago. I don't know the codes on the door to unlock it. how can I get the codes or reset it.


You will need the original factory programmed keyless entry keypad code to program your own code. To locate the original keypad code, open the right/rear door. Pull the on-body rubber weatherstrip out, around the rear side of the door closure. Fold the right/rear seat back down into the locked position to facilitate access to the right/rear seat belt anchor. Carefully pry the upper plastic panel that houses the height adjuster and seat belt anchor off the body taking care not to damage the panel. Now pry the lower panel outward just far enough to enable access to the Vehicle Security Module, where you'll see three electrical connectors plugged into it, colored green, gray, and blue. On the module will be a series of digits on a label similar to 2L2T-15K602-EA. Beside those digits are five numbers. Those five numbers are the key-less entry keypad code. Once the original keypad code has been obtained, you will need to enter it, press the 1/2 button within 5 seconds to activate the programming mode. Holding the 1/2 button for more than 2 seconds after activation will erase the the code you programmed. The existing code will not need to be erased to program a new code. Within 5 seconds, enter the new 5-digit keypad code. The door locks will lock and unlock to confirm the new code is programmed. Hope this helps Tim

Apr 06, 2011 | Ford Explorer Cars & Trucks

1 Answer

Factory ringtones


Sir,

You can lock your phone manually or set the phone to
lock automatically whenever you turn it off.
To use a locked phone, you must enter the unlock
code. A locked phone still rings or vibrates for incoming
calls or messages, but you must unlock it to answer.
You can make emergency calls on your phone even when
it is locked (see page 68).
Locking Your Phone Manually

Find the Feature > Settings > Security
> Phone Lock > Lock Now


Unlocking Your Phone
Tip: Your phone’s unlock code is originally set to 1234.
Your service provider may reset the unlock code to the last
4 digits of your phone number.


Setting Your Phone to Lock Automatically
You can set your phone to lock every time you turn it
off:

Find the Feature M> Settings > Security
> Phone Lock
> Automatic Lock > On

If You Forget a Code, PIN, or
Password
Note: Your phone’s 4-digit unlock code is originally set to
1234, and the 6-digit security code is originally set to
000000. Your service provider may reset the unlock code
to the last 4 digits of your phone number before you
receive your phone.
Press To
1 keypad keys enter your unlock code
2 OK (+) unlock your phone
Find the Feature > Settings > Security
> Phone Lock


Master
Clear
Clear all user settings and entries
except SIM card information, erase all
downloaded pictures and sound files,
reset all options except unlock code,
security code, and lifetime timer:
M > Settings > Initial Setup
> Master Clear
Caution: Master clear erases all
user-entered information (including
phonebook and datebook entries) and
user-downloaded content (including
photos and sounds) stored in your
phone’s memory. After you erase the
information, you cannot recover it.


Thanks
Good Luck

Don't forget to rate the solution

Jul 05, 2008 | Motorola Mobility Mobile PhoneTools 3.0...

Not finding what you are looking for?
Weiser Lock POWERBOLT ELEC DEADBOLT Logo

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Azam Ali

Level 1 Expert

31 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...