Question about Washing Machines

1 Answer

Hotpoint aquarius wf541 flashing lights

Code 3and 4 flash could be thermister/heater how do I take top/back off to test them.any manual or exploded view.

Posted by on

  • 2 more comments 
  • johnboy31 Sep 29, 2008

    contacted hotpoint flashing light 3,4 told to check thermistor/heater finding difficulty locating exploded view .

  • tinytinsel Nov 28, 2008

    I have a hotpoint aquarius Wf541 and all the lights flash when the machine is first switched on. Unfortunately I cannot find the instruction manual to find out what this is trying to tell me. Any ideas?

  • Anonymous Mar 12, 2014

    FLASHIN CODE f-13

  • Anonymous Mar 12, 2014

    FlASHING f-13 Code
    won,t wash

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 247 Answers

Hiya m8 how old is this washer if its over 5years then youll be looking at the thermostat and heater element being at the front of the washer which its easier to take the complete front off to get to and see everything clearly do me a faviour and pull the kick strip off and tell me if theres screws behind it to take the front off

Posted on Oct 01, 2008

  • sandi18 Jun 25, 2011

    I have a hotpoint aquarius the machine will not open and at the end of a cycle the on button flashes any advise

×

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How dop i reset e54 error of gestetner 2715?


To rest the error code > press the yellow Clear button then enter 1,0,7 then press and hold the red Stop button and hold till the screen changes. Then turn the main power switch OFF then back ON..... If the code comes back, you may have a thermister that is shorting out. Good Luck

Aug 12, 2012 | Gestetner Office Equipment & Supplies

1 Answer

Rheem model 41vrp40n flashes twice and stops working


Error code means that you have electronic gas control valve.

Copy following link to identify gas control valve, read error code meanings for each, and download service manual relevant to each gas control, but not specifically Rheem since rheem does not post service manuals.
http://waterheatertimer.org/How-to-troubleshoot-gas-water-heater.html#intellivent

The fact that water heater restarts, means that water heater is getting gas, getting sufficient air for combustion, thermister is ok, gas pressure is good, etc.
The fact that you unplug and replug water heater and it works, shows that you have power vent model.
Since water heater worked correctly before, 2 flashes with Rheem power vent model could mean that pressure switch has failed.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Jul 29, 2012 | Water Heaters

1 Answer

I have a Samsung Induction range and it has an SE error code on the rear left burner contro. I cannot get the code to clear so my whole range top is inoperative. How can I fix this.


"SE" error means you have a shorted membrane keypad.

There should be a "mini-manual" (tech sheet) hidden inside the unit behind the control panel or in the back cover, which is very helpful when troubleshooting, testing, and locating components.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Jan 27, 2011 | Samsung Microwave Ovens

1 Answer

I a LG 22860sw refrigerator ERROR CODE DH


The main Pcb as well as the defrost thermistor are in the circuit as well.
The thermister is attached to the evaporator with wire ties and connects to the roof of the freezer behind the fan assy.

I have seen the thermister connector pull out of the connector at the top of the freezer beacuse the wires were to tight. Remove some of the wire ties and reinstall the connector.

Jan 12, 2010 | LG Refrigerators

1 Answer

I have a al1216 copier of sharp. Now didn't anything flashing only 4/h frequently


H4 00 Content Too cold fusing section Detail The temperature does not reach the preset value within the specified time (3 min. in usual modes; 5 min. in curl correction mode.) after the power relay is turned on. Cause Thermister defective Heater lamp defective Control PWB defective Thermostat defective AC power supply defective Interlock switch defective Check and remedy Check heater lamp for blinking with SIM5-2. If lamp blinks properly: Check thermister and its harness. Check thermister input circuit of control PWB. If lamp does not light: Check heater lamp for broken wire and thermostat for operation. Check interlock switch. Check lamp control circuit of AC PWB and control PWB. Clear the trouble with SIM14

Nov 02, 2009 | Sharp Office Equipment & Supplies

1 Answer

Dishwasher prog light is flashing and pump is running nothing els


ok, just a few minutes after posting this as a fault, I have opened the covers, the machine has a leak, the undertray has a sensor which has detected this, flashing light (prog 45 degC wash) flashing is a code to indicate leak sensor active.
Other prog lights flashing indicate a different fault, the following details each... this is a cut/paste from another forum site, copied without permission....

jawa592rc_a04.gif on 6th Feb 2008
Cannot guarantee 100%accurate but you all might like what the flashing fault codes actually refer to, note what follows are pointers to what bit has gone wrong only. You should have the programmes running left to right: led1=intensive,led2=normal,led3=eco,led4=fast,led5=prewash,led6=delicate wash.ok so when this heap of western european tosh goes wrong one or two lights will flash this is what they mean:led3=m/ch has o/flowed water . ie the base underneath has sensed a leak.4=i/let h2o valve u/s or slow fill.5=thermister(electronic thermostat) is u/s or more likely the pcb .6=timeout heating which means the thermister senser between the door halves has become faulty or detached.3+4=no pump out,slow pump out,pcb u/s,blockage.4+5=tap off i/let valve.3+5=wash motor not coming on -seized,winding o/cic.but can also mean mesh plte filter badly blocked.1+4software fault with pcb.4+6=heating cic u/s (usually the heater tube )but can be the heater relay on pcb.3+4=pcb u/s.I don`t except any responsiblity for this being spot on or near spot on!! hope this helps someone.Try NOT to electrocute yourselves please!! If your not at all confident walk away and get "someone" who knows what they are doing.Cheers. jawa592

Jan 21, 2009 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

1997 Suburban-4 wheel drive problem-Won't work-Indicator flashing


It sounds like the spring loaded pin that the plunger activates is stuck or broken. If its not to cold tap on the housing and see if it kicks in. If not consult the book for an exploded view. If your manual does not have the view go to the nearest dealers parts department and ask them to print you one.

Apr 22, 2017 | 1997 Chevrolet Suburban

1 Answer

My lower oven does not work; top oven works fine


You can usually find helpful exploded view diagrams and order parts by entering your full model number here.

Thereshould also be a "mini-manual" (tech sheet) hidden inside the unit behind thecontrol panel or hidden inside behind the back cover, etc., and it's very helpful when troubleshooting, testing, and locating components.


Nov 24, 2008 | Microwave Ovens

2 Answers

No heat in dryer


if you can see your heating element, use a meter to test for continuity. remove the clips or wires attached to the terminals of the heating element and put the probes of the meter.
the reading should be close to short since it is a heater. maybe 1 to 10 ohms.

tnx 4 using fixya,

drcool

Sep 28, 2008 | Hotpoint TDC32 Electric Dryer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

903 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...