Question about Hitachi 61SDX01B 61" Rear Projection Television

Open Question

Hitachi 61SDX01B Convergence problem

Wavy red lines at top of screen, red halos around objects. Magic Focus cant fix.

Posted by on

Ad

5 Suggested Answers

ladywinn

ladywinn

  • 5138 Answers

SOURCE: hitachi 61udx10b

Replace Both of your STK ICs they are your convergence ics they are big black ICs will have Part# on them for example STK392-110, if they are 110s use 180s, if 020s use 040s other wise replace with exact same number. To get Parts call Electronix 1-800-223-3205

Posted on Dec 30, 2008

Ad
ctf1800

Cary Farah

  • 4402 Answers

SOURCE: shadow around objects in picture...shadow is bluish

KIT10 $29.50
Repair Kit for Hitachi convergence Chassis DP-14G
KIT10 Includes 2 pcs STK392-150 , 1 each of the following 1W axial lead fusible resistors:


http://www.digitalhome.ca/forum/showpost.php?p=564268&postcount=220
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html

Posted on Dec 05, 2007

Ad

Anonymous

  • 579 Answers

SOURCE: Hitachi 51SWX20B's screen has 3d effect

You have a problem with the STK convergence modules. They're on the center circuit board attached to an aluminum heat sink that's about 8" long and 6" tall. You may be able to recreate the problem (hour glass effect) by gently moving the heat sink (which the modules are connected to). This gives the hour glass effect on the picture and the advanced convergence screen. This is an indication that the modules pins aren't solidly connected (meaning soldered) properly. Remove the circuit board and clean the old solder off & resolder the modules pins to the circuit board reconnected the board and then retest by again pushing on the heat sink. The "factory" job was good enough for 3-4 years but the heat (and these modules do create a lot of heat) and stress created from repeated use eventually takes it's toll, weakens the pin connections and our problem occurs. take the appropriate cautions working around the high voltage of the set & use a non-conducting piece of wood to push the heat sink when doing tests.
If soldering doesn't help, then the modules have died and need replacing. Don't buy the $10 cheap ones. Most of them have an upgraded version that is stronger. Also look for any burned resistors in the vicinity of the modules.
Best of luck, hope ya fix it.

Posted on Feb 15, 2008

Anonymous

  • 121 Answers

SOURCE: PROJECTION TV HITACHI ULTRAVISION COLOR CONVERGENCE PROBLEM

it sounds like your blue convergence ic is getting weak you need to replace the ic's STK392-110 and you should replace both because when 1 is bad the other will go real soon. They are inexspensive at the sight I posted and you will also get free tech online support if you purchase them there.
http://servicemanuals.vstore.ca/

Posted on Apr 13, 2008

Anonymous

  • 1 Answer

SOURCE: HITACHI 43UWX10B Color Convergence

I have a yellow swoosh (shape of the nike swoosh) on the top of my screen with a blue 2" inch line under it. I also have a blue spot on the bottom left of my screen. I hit the Magic Focus to see if that would help and it did nothing. Help!

Posted on Oct 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HITACHI 57F710S - no red in picture. Magic Focus shows Red, Blue and Green perfectly. But when "Magic Focus" is done, picture doesn't have red in it. Help!


Projection sets have two very common problems listed below. bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

The first common problem is convergence

These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Apr 25, 2011 | Hitachi 51F710 Rear Projection Television

2 Answers

Hitachi 43fwx20b Convergence Problems


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony,Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit wiith instructions from the links below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms
  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted or warped
  • No Audio/Video - makes a chirping sound.
Problem #2

Another common problem is dull or washed out video.
Your TV may have one or more of the following symptoms....
  • Dull looking picture
  • White looking picture
  • Halos around objects
  • Red/Orange looking picture

You can see some more examples and find a fix here
bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Feb 25, 2010 | Hitachi 43FWX20B 43" Rear Projection...

1 Answer

Goes through magic focus than in the middle stops and displays #5


This is a common problem. Its called a convergence failure.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Feb 19, 2010 | Hitachi 46F500 46" Rear Projection...

1 Answer

Will not focus


This is a common problem. Its called a convergence failure.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Feb 02, 2010 | Hitachi 57F500 57" Rear Projection...

1 Answer

Blue shadows throughout the screen and magic focus freezes with "5" displayed?


This is a common problem. Its called a convergence failure.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Jan 30, 2010 | Hitachi 43FDX20B 43" Rear Projection...

1 Answer

60" hitachi 60SDX88B screen shows some green distortions in the top and bottom of the screen. Magic focus does not fix this. Help?


This is a common problem. Its called a convergence failure.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Dec 21, 2009 | Hitachi 60SDX88B 60" Rear Projection...

1 Answer

Hello, I've got red wavy lines across screen


There are two common problems with these sets.

Problem #1) Convergence

Symptoms:
  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Oct 22, 2009 | Samsung HCM5525W 55" Rear Projection...

1 Answer

We have a convergence problem that Magic Focus won't fix. Our screen has a 3D effect and there are red bows on the screen. Is there a manual convergence setting somewhere for us to try since the magic...


Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.

The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded overs.


You can find more details and solutions here on Fixya at the following link below. Or click HERE


3d884ac.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Mar 04, 2009 | Hitachi 50UX57B 50" Rear Projection...

1 Answer

Can't set red convergence on 65" Hitachi


Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted
  • No Audio/Video - makes a chirping sound.
Example Photo:
5f6e85c.jpg
Problem #2 CRT Fluid has clouded over.

Symptoms


  • Dull Video, Washed out
  • White/Bright looking video
  • Halos around objects
  • Red/Orange looking
Example Photo:
ee1ca68.jpg

You can see more examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Dec 24, 2008 | Hitachi Director's Series 65XWX20B 65"...

1 Answer

Hitachi Projection tv


Projection TV sets have two very common problems listed below.

Problem #1) Convergence


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Jul 17, 2008 | Hitachi 43F300 43" Rear Projection...

Not finding what you are looking for?
Hitachi 61SDX01B 61" Rear Projection Television Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76237 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...