Question about Euro-Pro Shark 80 - 7133

1 Answer

My presser foot won't go up and down. Any suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Euro-Pro Master
  • 7,365 Answers

It's very possible that a part in your machine has come loose or broken
it needs to be serviced

Posted on Feb 01, 2012

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The pressure foot handle is loose and my foot won't go down what's wrong


Grasp the presser foot bar and pull it down. It is likely that the loose bar has jumped off of the cam on the lever. you'll need to figure out how to get in there and tighten it or replace a broken lever.

Good luck.

Oct 11, 2012 | Singer 9900

1 Answer

The machine says the presser foot is not down and it is so it won't sew


it could be a problem with the motherboard, the sewing machine needs to be checked

Oct 10, 2012 | White Sewing Sewing Machines

1 Answer

Feeddog won't move with pressure foot down. I have a Baby Lock BL4-428. I haven't used it in a while. I cleaned it up and oiled it. The feeddog moves when the pressure foot is up but as so


it sound like the feed dog & the presser foot need to be adjusted
so they work togeather,,it's very possible they need to be timed
a sewing machine repair shop can tell you for sure

Sep 05, 2012 | Baby Lock Sewing Machines

1 Answer

I have a 9960 singer machine and am trying to use the buttonhole presser foot for the first time and I can not get it to sew T


the buttonhole foot snaps on to the presser bar, there's a little lever at the back of the presser bar that releases the foot, then put the buttonhole foot down on the needle plate & use the presser foot lifter (number 11) to lower the presser bar down onto the buttonhole foot & you'll hear a click sound when it snaps on & make sure to use the buttonhole lever(number 31) because the machine won't sew a buttonhole unless that lever is pulled down.

Apr 26, 2012 | Singer Sewing Machines

1 Answer

Silvercrest overlocker - the 'red' pathway thread won't progress through


have you tried changing the needle?
since you've only had the machine for a week, I'd suggest taking it back & getting another machine.

Mar 26, 2012 | Sewing Machines

1 Answer

My Janome Harmony 1017 won't sew all the zigzag stitches. Stitches 5,7 and 8 bog down after just two or three stitches because the fabric isn't moving through the machine. Any suggestions?


when the fabric does not move then the feed dogs under the needle plate need to be checked to see if there up or down.
if the feed dogs are down then the lever or switch needs to be pushed up into the correct position
if the feed dogs are up & they are not moving the fabric like there suppose to, cause it's there job to move the fabric against the presser foot,, then they need to be check

the gears that do the zig zag stitches should be checked to make sure there not worn & weather they might need be be greased

Aug 29, 2011 | Janome Harmony 1017 Sewing Machine

1 Answer

How do i re-install the all purpose foot back onto the machine


take the presser bar lifter & lift it up, if you look close it has a small notch under the front
place the all purpose foot down under the presser bar, make sure the presser bar notch get on to the pin that's across the top of the purpose foot & they should snap togeather

Aug 03, 2011 | Singer 3116 Simple

1 Answer

When pressing the foot control the machine won't run, it shows the presser foot blinking on the screen even when the presser foot lever is down.


check the connections, if they are good, your foot pedal has a short in it, so its not completing the circuit when depressed

Jul 15, 2011 | Husqvarna Rose

1 Answer

HOW DO I ATTACH PRESSER FOOT G TO MY MACHINE??


there are 2 type of presser bar foot clamps
one allows you to snap on the foot--raise & then lower the presser foot holder until the cut out is directly above the pin on the foot,,as you lower the presser foot holder the presser foot will automatically engage when put down on the pin area

the second is a shank & foot combined & there is a screw on the presser bar,,unscrew it some & put the shank up around the screw & retighten the screw

Nov 24, 2010 | Janome Memory Craft 5700

Not finding what you are looking for?
Euro-Pro Shark 80 - 7133 Logo

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Euro-Pro Sewing Machines Experts

Irene Tulloch

Level 2 Expert

498 Answers

MissFixIt828

Level 1 Expert

70 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you an Euro-Pro Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...