Question about Health & Beauty

2 Answers

Quantum 610 error #107 Charger Inhibit

I get an error when i try to engage wheel chair it says STOP: #107 Charger Inhibit. and it will not move?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

On my powerchair it had charger inhibitor error 107 and chair would not move what do I do ?

Posted on Aug 03, 2016

Ad

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I just had same code. I took off rear cover and unplugged a rubber cap at the end of a long skinny group of a few wires. looks like a charging wire kinda. and unplugged the main plug. I did not unplug the two larger battery plugs. when I plugged them back in firmly everything was back to normal.

Posted on Aug 26, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

PAPACREN

  • 1 Answer

SOURCE: Jazzy Quantum 600 power wheelchair - On the

THE WHEELCHAIR WILL ONLY TILT IT WILL NOT GO FORWARD OR BACKWARD USING THE JOYSTICK

Posted on Jul 14, 2011

Anonymous

  • 40 Answers

SOURCE: Jazzy 1113 Power wheelchair. Batteries are fully

Yes, the main controller module can be very expensive to replace. I would take it to a reputable dealer if the battery replacement does not help.

Posted on Apr 05, 2009

Anonymous

  • 4 Answers

SOURCE: Hooveround MPV won't move

Most likely either one or both of the batteries have a dead cell. Have your batteries load tested to check their condition.

Posted on Aug 13, 2009

oregoon

  • 175 Answers

SOURCE: joystick in programming, inhibit and/or charging

This is usually due to either the joystick getting knocked off center or a fault in the control module. If the joystick has suffered a hit such as somebody falling onto it while getting in the chair, or running the joysitck under a table or counter-top(happens often), it knocks the alignment off so that the controller thinks that the joystick is activated, and it will prevent the chair from moving until it is back in its proper location. Examine the joystick for signs that it has suffered a trauma such as the rubber boot being torn, dents on the cover, paint from a collision, etc. Invacare is going to charge you about $1,300.00 for a new joystick, or, you can try sending it to a repair shop. I found one here that I used once and it turned out cheaper...by a lot$. Here's the link.
http://www.flightsystems.com/cart_controls/wheelchair_powered_scooter_market_cart_controls.htm

Keep in mind, it may also be the controller. The only sure way to tell is to swap out the joystick with a known good one, and see if it fires up, if not, then it's the controller. Get your wallet out. I don't know of anywhere to go but to Invacare for the controller. You don't say what kind of wheelchair it is, but if it is one that the controller is built into the joystick then the link above should be able to fix it. If the controller is separate and located in the base, then you have to buy a separate controller from Invacare. To tell, the all-in-one controller will have a very thick chord running from it down into the base; about 3/4" diameter. A separate joystick and controller-in-base will have a smaller chord, about pencil-sized running down into the base fronm the joystick, and will lead to the controller in the base. Good luck.

Posted on Oct 09, 2009

rulds2008

Grand Canyon Tech

  • 3866 Answers

SOURCE: i have a quantum power

The issue on these is ether the motor has burned out on you or the battery is not getting enough current to turn the motor or you got a bad relay from the control panel to the motor, There is no way to diagnose this without having someone to come out to your home. But I can tell you this much my dad had one of these and his motor was the issue and when you got a motor issue in these mobility devices you might want to concider ordering a new chair if possiable. Just the parts and labor alone is over $1,500 trust me been there done that. So the best thing I can tell you is run test on the chair and if you cannot do that you need someone to visit your home to do that for you the cost to visit is like $125 bucks minium as they got to charge for there gas and there labor when they arrive. I would call the scooter store for a tech i nyour area.



Hope my information helps tho please do click the accept button for my efforts.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Charger inhibit error #107


Hi remove rear cover & check to ? if the wiring connections r all plugged in firmly .....good luck

Oct 11, 2016 | Quantum 600 E Electric Wheelchair - Used...

1 Answer

When I go To move the chair comes up with error 107. , charger inhibit . I disconnected the charger. What can I do next


after do a test restart the chair. make sure both freewheel levers are locked in drive mode (hard to push), restart, make sure your connections are good, to the motors and brakes. what kind of Joystick is this?

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Apr 07, 2016 | Quantum 6000 Power Chair - Used Electric...

1 Answer

Charger inhibit error


Hello Debbie Waters,if you contact a Wheelchair/Scooter Repair Shop.Give them what you see as to (WHY) & ask for a price on the Part.I hope this has helped,Colin.

Jan 16, 2014 | Quantum 6000 Power Chair - Used Electric...

1 Answer

I replaced the battery charger with a quest charger, chair now charges but wont function i guess because of the inhibit feature how can i fix this


A few things to consider: A blown charger fuse can cause the charger inhibit to activate. Determine if all controller connections are plugged into the power base properly. If the 3-pin charger inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

May 09, 2013 | Jet 3 Ultra Power Chair

1 Answer

Blinking yellow wrench light on pride jazzy 614 HD


Your version has a Dynamic Controls model controller and joystick.
Unplug the charger and engage the motor/brake lever so the chair is no longer in free-wheel mode (con't push by hand)
Turn the chair off, wait 5 seconds, turn the chair back.
If chair still does not run and your wrench is flashing you have a problem. Count the wrench flashes - the flash count indicates the error detected. 3, 4, 5, and 6 flashes indicate and error with the motors.
3=Left motor fault
4=Right motor fault
5=Left brake fault (may not be engaged)
6=Right brake fault (may not be engaged)
Any other fault code usually means the electronics or wiring is bad and not worth fixing.

Jan 06, 2013 | Pride Jazzy 614 Hd JAZZY 614HD

1 Answer

Jet 3 will not turn on but when you plug charger cord in it will light up the entire length of the battery indicator when you push the switch. Chair will still not move. Controller is a PG Drives Pilot...


the batteries are not charged and need to be replaced. The reason you have lights is because the charger is supplying power to the chair and the chair will not move when the charger is plugged in because of the inhibit function. Replace the batteries and make sure you charge before use Hope this helps

Apr 15, 2011 | Pride Used Mobility Jet 3 Power Wheel...

1 Answer

When I plug it in to charge the red and amber lights stay lit and the green flashes and if i move the joystick everything is backwards push forward goes backwards left is right. b4 when it was plugged in...


sounds like a charger inhibit problem. Whenever you charge your chair the charger inhibit shuts down the chair so it can't be moved while charging. If you are getting this then that function is not working. Lets try this if you know of someone who has a chair or scooter with an off-board charger see if you can borrow it. Plug the off-board charger into the charger port located under the front of the joystick (don't have the on-board charger plugged in) and then turn the charger on. turn the chair's power on and you hopefully will see the lights blinking again indicating a charger plugged in (charger inhibit) the lights on the charger should be red and yellow (yellow turning green when fully charged) If you still get the problem with the off-board charger then your problem is in the controller or power module and this requires a new one. If Medicare paid for your chair you can call Repair Xpress @ 1-877-81-3733 or Roadrunner Mobility @ 1-800-467-2668 to have them fix it for you and bill Medicare for most of the repair costs. Hope this helps you

Oct 31, 2010 | Invacare Pronto M51 Power Wheelchair

2 Answers

Wont turn on light just flash back and forth on speed setting


gilly your controller still thinks you are charging the chair. This error is a charger inhibit error which means that when you have the charger plugged in you can't drive the chair. If your charger is not plugged into the chair then you have a problem that needs to looked at by your provider where you got the chair or by a tech Sorry I don't have a quick fix Hope this helps you

Sep 25, 2010 | Pride Mobility Products New Pride Mobility...

1 Answer

Pride Jet 2 power chair with with 3 red and 3 yellow lights flashing. Batteries checked ok under load, all connections have been checked. I moved the chair and it would not move again. Just that quick.


Hi. The fault code you have is called the "Inhibit active".
It can be caused by a blown charger fuse, which causes the charger inhibit to activate.
Also if the 3-pin charger inhibit connector is not plugged in properly, or the connector is faulty, then the charger inhibit feature will activate.
Hope this helps. Neil.

Jun 22, 2010 | Jet 3 Ultra Power Chair

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

3,533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1412 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Jeff Bird

Level 3 Expert

1344 Answers

Are you a Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...