Question about Epson AcuLaser C1900 Printer

1 Answer

Transfer unit message will not go even after replacing.

I have replaced with new but I cannot clear the message which should clear itself according to manual.

Posted by on

Ad

1 Answer

PJ28 Socket for EEPROM (IC3)
C1900 fix
if you remove and replace the pcu and transfer belt too many times
the unit detects how many times its replaced
and stores it to this ic
i think this from a technical view
if you simply replace the eeprom ic with a blank one
then the unit will rewrite dump data to the eeprom
as per first 'out the box' factory the dead giveaway is the need to change over this ic
if you change the controller board where the ic lives
i would assume to preserve settings

i would first remove the units carts
developers {using power off mode method {see service manual you can download this on the net google c1900 service manual }}
transfer and pcu
now replace the eeprom with a blank new one {easy to get for $}
once all back together power it on wait till it inits or vents an error
power off and replace all carts
now power up and give it a try
i think looking at the softwares flow charts in the service manual
this to be the case and i think the software is cleaver enough to do
some simple maths to work out the real state and stored state of both units
so as i say if you've been messing around with stuff while its on
there is a chance these presets have been exceeded or corrupted by say a power outage as it writes these values to eeprom
moreover the firmware in the printer will show strange stats
like some posters report when changing fuses
im sure there will be a max change transfer and max change fuser and pcu
values set to it from first init
as it seems the only nv storage
i have not had to try this method would be nice to see it work
but it sounds logical and worth a go
if your having that type of issue that just wont go away
as for the fuses this is well known
but i know there is more to it with some members outcome when resetting them
it will reset all the stats print counts etc
equivalent to clocking yer motor
to factory and the pesky counters
the reason i say take the units out is incase it pulse the blow fuses lines
on init to default 'factory'
then it would wipe out both fuses

Posted on Apr 03, 2012

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to clear notification transfer roller needs to be replaced soon.


1. Touch Menu.
2. Touch [Counter].
3. Touch [Display Keypad].
4. Press the following keys in this order.; Stop -> 0 -> 0 -> Stop -> 0 -> 1
5. Enter the CE password and touch [END]. (IF required)
6. Counter
7. Life
8. Transfer Roller Clear

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Nov 19, 2015 | Genuine Konica Minolta Konica Minolta...

1 Answer

I have a Konica Minolta bizhub C351 that has an error message " transfer roller unit needs to be replaced soon" I purchased and replaced the "image transfer roller unit 4049-411 that also has the nu


Enter in the service mode:
Press Utility key - Meter count - Details - Counter mode - select present parts life and reset(clear) the transfer roller counter.

Mar 25, 2013 | Konica Minolta bizhub Office Equipment &...

1 Answer

I was getting a message that the transfer belt needed to be replaced and I replaced it. But the message won't go away.


try this:

1. Press # sign; then 1934
2. Press MENU
3. Arrow to Tech Mode (not User Mode); press OK
4. DataSetup; move arrow to Clear All Memory
5. Clear All Memory; press OK
6. Choose coonutry; press OK; will erase and print out configuration report; clearing the transfer belt error.

This wipes out the counter on the Transfer Belt. Clear All Memory means all your settings are wiped out. This also reset all the counters EXCEPT the imaging unit counter.

Trust this helps. Please vote.

Dec 14, 2010 | Samsung CLP 300 Laser Printer

1 Answer

Minolta 2200 service code 16


(TABP0902037EN00) - magicolor 2200 DeskLaser - What are the steps to fix a service call 16H transfer belt rotate error on a magicolor 2200 series? (TAUS0805552EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'ACC_Getstatusr EC;Code=__D, Resetting ACC to Initial State' (q0601101) (TAUS0805008EN00) - magicolor 2 + - Installing CrownNet code on the Crown monochrome printer (q0499042) (TAUS0803976EN00) - magicolor 2200 + - Flashing System Code to DeskLaser to Correct 'Starting System Firmware Image' Message (q0202107) (TAUS0806277EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Toner Missing' (q0800700) (TAUS0806280EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Transfer Belt Missing' (q0800703) (TAUS0806281EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Fuser Missing (q0800704) (TAUS0806282EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Oil Roller Missing' (q0800705) (TAUS0806283EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Toner Low' (q0800706) (TAUS0806284EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Toner Empty' (q0800707) (TAUS0806286EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Fuser Unit' (q0800709) (TAUS0806287EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Transfer Belt Life Low' (q0800710) (TAUS0806288EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Transfer Belt' (q0800711) (TAUS0806289EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'OPC Drum Life Low' (q0800712) (TAUS0806290EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace OPC Drum' (q0800713) (TAUS0806292EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Waste Toner' (q0800715) (TAUS0806293EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Oil Roller Life Low' (q0800716) (TAUS0806294EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Oil Roller' (q0800717) (TAUS0806295EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Put Media in Input Tray' (q0800719) (TAUS0806296EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Put Media in Upper Bin' (q0800720)

Dec 11, 2010 | Minolta magicolor 2200 DeskLaser Printer

1 Answer

My 4700dn is giving me the replace transfer kit message. I have swapped out known good transfer kits and the printer prints fine but I still get the replace transfer kit message. What can I try next?


The message only clears when you install a new transfer unit, one that hasn't been used before. If you want to clear the message, you'll have to install a brand new transfer belt.
If you know the service PIN for the 4700, you can probably go into the service menu and clear the message, but otherwise a new transfer unit is the only way to go.

Aug 11, 2010 | HP LaserJet 4700 Printer

1 Answer

How do I reset the replace transfer belt message on a Ricoh CL2000


You'll have to replace the transfer belt with a brand new one in order to clear that message. Installing a transfer belt from another machine won't clear it -- it must be a completely new unit.

Jan 04, 2010 | Ricoh Aficio CL2000N Laser Printer

4 Answers

Ricoh ap4510 - Maintenance Kit Issue


For the message to be cleared you should enter the service menu and reset the replaced elements

Jul 28, 2008 | Ricoh Aficio AP4510 Laser Printer

4 Answers

Transfer unit on bizhub C250


its not so hard, open side door, remove 2 screws, and pull out the transfer unit gently. and reinstall new TBU. BE VERY CAREFUL WITH NEW UNIT, DO NOT DAMAGE IT.

Jun 19, 2008 | Konica Minolta bizhub C250 All-In-One...

2 Answers

Transfer kit


The transfer kit is unrelated to the toner. On most printers it gives you the message that it needs replaced after X number of prints. Depending on page coverage and the quality of the paper you are using there may still be some life in it and you can clear the message and print until the image quality is affected then change it.

May 29, 2008 | HP LaserJet 4600dn Color Printer

1 Answer

"Cannot Adjust Fusing Unit"


The transfer belt needs to be replaced.

May 01, 2008 | Ricoh Aficio AP3800C Laser Printer

Not finding what you are looking for?
Epson AcuLaser C1900 Printer Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Alun Cox

Level 3 Expert

2679 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...