Question about Cisco Linksys E1000 WirelessN Broadband Router Network Routers

1 Answer

Help!!!!!!!!!!! I need to forward a port and i need to get to the wedsite. i put in the username admin and the password adminadmin then i get a 401 un authorized error pls help

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cisco Master
  • 2,277 Answers

Leave the user name blank and enter the password admin ( admin once only ).

Try this.
If that doesn't work then search for the Cisco connect software on your main computer. You might have installed the cisco connect software on your main computer while installing your router.
If it is windows computer then cisco connect software might be under All Programs.
If is a MAC computer then cisco connect might be under Applications.

Open cisco connect software.
Click on router settings. You will see the router name and password. If you click on Advanced settings, it will open the setup page.

If nothing is working then you will need to reset the router and reconfigure it.
Remember once you reset the router, you will need to reconfigure it from the scratch.

Click to see more information about cisco connect software

Posted on Apr 12, 2012



1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


How to Upgrade Firmware of Linksys routers........

As the application requires certain ports to be opened on the router,try to follow the steps below to configure the router. Since you are connecting behind the router, you are going behind a NAT firewall.Therefore, you would need to allow ports for the remote access application to go through the firewall. You would need to know what port number application uses. You can check with the program manufacturer for the information, or see the Help menu.

For routers with old firmware versions (without the Cisco web interface):

1.Open Internet Explorer.
2.After "Internet Explorer" opens, please typehttp:// into the "Address Bar" and click GO.
3.The "Enter Network Password" window will appear. Skip username and type admin (admin is the default password) as the password,and click OK.
4.You will need to click on the Advanced tab to the very right. Once the "Filters" area appears, please click on the Forwarding tab.
5.Once the "Forwarding" area appears, click the Port Triggering button. Once you've done this, a new window will appear.Enter the ports needed to be opened > Click Apply

For later firmware (that has the Cisco web interface)

1.Open Internet Explorer.
2.After "Internet Explorer" opens, please typehttp:// into the "Address Bar" and click GO.
3.The "Enter Network Password" window will appear. Skip username and type admin (admin is the default password) as the password,and click OK.
4.Click on "Applications and Gaming" then click on the "Port Triggering" Sub tab. Enter the ports needed to be opened >Click Save Settings.


Customized Trigger Port Range Incoming Port Range
Application From ~ To From ~To
WARCRAFT 6112-6112 6112-6112
WARCRAFT 6113-6119 6113-6119

Hope this help everyone that has problem with the game.

on Jan 05, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

Port opening


You can open port number for the game in following way.

Open a web browser like internet explorer or Netscape. Enter the ip address of your router in the address bar of your browser. In the picture above the address bar has in it. Just replace all of that with the ip address of your router. By default the ip address should be set to


You should see a box prompting you for your username and password. Enter your username and password now. By default the username is admin, and the password is admin. Click the Ok button to log in to your router.

Please visit our default username and passsword page, if the username and password shown above did not work for you.


Click the Customized Configuration button.

Click the Advanced link near the top of the page.


Click the Virtual Server link near the left of the page.


Enter the port to forward into the Public Port and the Private Port boxes. Select Both from the Protocol drop down box. Enter the ip address to forward these ports to into the Server IP box. If you are forwarding ports so you can run a program on your computer, you should enter your computer's ip address into that box. Put a checkmark in the Enabled checkbox.
When you're finished, click Save near the bottom of the screen to save your changes.

Hope it can resolved your issue

Thanks for using Fixya

Apr 09, 2010 | MSI Wireless-G RG54G3 Router

3 Answers

When I enter "" it's asking me username and pas


for the username use administrator and ofcourse the password that u have set

pls rate if it was any help

Jul 07, 2009 | Levelone CP TECHNOLOGIES LEVELONE...

1 Answer


Try typing into your web browser navigation bar and when it prompts you for a username and password type in this username = Administrator and the password should be: admin if admin does not work then use the password you made when setting up the router. once in the administrator menu look for port forwarding and use the port forwarding page to set up the port you want opened and the ip address of your computerif you need more help i will gladly try my best to walk you through the steps. i must go for now

May 08, 2009 | Linksys WAG200G Router

2 Answers

Router configuration

you need to open the configuration page of the ADSL router and enter the configuration settings manually.

into your browser type >> username: admin >> password: admin

then in the setup page...enter the correct setting provided by your encapsulation...multiplexing..VPI / VCI them if you have to...then enter your username and password for your internet account (you need to contact your ISP also for this.)

if ever you still cant enter into routers setup can reset it to factory the back of the router...there is a small hole..(usually in red border).....

turn on router >> then push a stick into the hole (small stick enough for the hole) for about 5 secs...then try again >> username: admin >> passoword: admin

if you need further info...please post back. good luck

Feb 09, 2009 | D-Link DI 514 Wireless Router (DI-514)

3 Answers

How to reconfigure router

you may need to reset to restore the defaults.

the the default username: admin and password: admin

Jan 16, 2009 | Blitzz Technology BWA711 (B3WL000900)...

1 Answer

Wrt54g wireless router

The default password of the linksys router is admin just leave the username blank, if admin did not work reset the router so it will be back to its default settings with default password admin and leave the username blank ..

Hope that helps........

Aug 11, 2008 | Linksys Wireless-G WRT54G Router

1 Answer

Port forwarding trouble

enter admin for username and password

Aug 05, 2008 | Westell Wirespeed VersaLink...

Not finding what you are looking for?
Cisco Linksys E1000 WirelessN Broadband Router Network Routers Logo

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers


Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides