Question about GE Profile Spectra JGBP90 Gas Kitchen Range
Yesterday I put the oven through the self-clean cycle and it seemed to run fine. I pressed self-clean, the display showed 4.00 hours, I hit start and off it went. The display then showed "oven clean/locked door", and the timer ran down from 4.00 hours. When the cycle ended 4 hours later, I had a clean oven, however, the locked door display would not go off. My husband managed to get the door open, but now the oven will not work - bake or broil. When I try to select the bake or broil function, it will not allow me to set the temperature. The range top burners all work. The door opens and closes and appears to latch properly. I set it to run the self-clean cycle again, and the display showed all of the appropriate messages, however the oven door did not lock. I stopped the cycle after about 10 minutes. Probably important: about 1 year ago I had food placed too close to the broiler and the oven caught fire. It was quickly extinguished, but ever since I turn on the oven to bake or broil, the top of the range gets hot - hotter than it used to. It is almost too warm to the touch, as if I burned through the insuluation. I have not put the oven through the self-clean cycle since the oven fire - until yesterday. I have been baking and broiling without incident until yesterday.
My Spectra XL44 suddenly refuses to ignite the baking portion of the oven - broiler and top work just fine. The day before it was working fine. Wondered if it was an electrical egnition problem - gas feed or what??? Help!! Mregressor@aol.com
Posted on Feb 28, 2010
Hi I had a very similar issue that I finally resolved yesterday. I ran the self-clean cycle but wanted to go to bed so hit cancel with about 1 hour to go. The oven showed "door locked" but I simply thought this was because the oven still had to cool.
In the morning though the oven still showed "door locked" and I was unable to open door. I spent hours trying to find a solution on the internet plus on the phone with GE. Then yesterday I finally fixed the problem.
Hopefully this will help others with the same issue.
If you have the same problem where the door is continually locked after a self clean cycle unplug your oven for at least 24hrs. Next gently lift the door by the handle and wiggle it upwards. If you do this correctly you can get the oven door open. However do not force it! Just gently wiggle the door upwards and forwards and it should open without any issue..
Next plug the cooker back in. If like me the cooker still shows "door locked" you need to do 1 more step. On the front left of the cooker just behind the door there is a black button. Push this button and hold it in, then press the cancel button and hold both for about 30 secs.
If you have doen everything correctly the door should unlock and you can use the oven for cooking again!
Posted on Nov 22, 2009
Carol, let me see if I can help you with this. First try killing the power to the oven for 30 seconds and see if the locking mech resets. If nothing changes try this: kill the power for at least ten seconds, power back up,simultaneously press the cooking time, delay start and the number 8 pad. Test should appear in the display. Press and hold the self clean key, this will test the lock motor and cam assy. The display should show 2 on the left (for locked) and change to 3 on the left for unlocked. Travel time of the cam will display a 0 between locked and unlocked. You must hold the self clean key for these changes. This latch mechanism is thermally controlled and sends a message to the main board to lock and unlock during self cleaning. We are just bypassing this with this test. Your temperature sensor may have gone bad during the self cleaning cycle. This is the probe located in the oven cavity. If you know anyone that is handy with a meter, it should ohm out at 1092 ohms at room temp. If this checks out, someone will have to open the top and check the lock motor and cam. Catriver..post back.
Posted on Nov 13, 2006
GE PROFILE GAS RANGR STARTED THE SELF CLEAN BUT FORGOT TO TAKE OUT RACKS SO I STOPPED THE SELF CLEAN BUT THE DOOR IS LOCKED AND THE LIGHT KEEPS FLASHING LOCKED
Posted on Feb 04, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: ge spectra xl44 stove
Most likely the oven ignitor is bad or weak. You can look at it and see how it compares to the broil ignitor. If you see a whitish color on the ignitor and if it doesn't fully glow then it needs to be replaced.
Posted on Oct 22, 2007
SOURCE: GE Profile XL44 Spectra gas oven
try to hold down the light switch on the door set it up for another cleaning hit start when oven clean door lock showes hit cancel if that doesnt work try unplugging it for three min fyi the doors can take up to an hour to un lock after cleaning its so it dont burn your face off from the intense heat after cleaning some take 2
Posted on Feb 14, 2008
Tips for a great answer:
Sep 14, 2010 | GE Profile Spectra JGBP90 Gas Kitchen...
Mar 09, 2010 | GE Profile Spectra JGBP90 Gas Kitchen...
Feb 20, 2010 | GE Profile Spectra JGBP90 Gas Kitchen...
Dec 09, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...
Jul 24, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...
Jun 29, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...
Jun 28, 2009 | GE Profile Spectra JGBP90 Gas Kitchen...
Jul 23, 2017 | GE Profile Spectra JGBP90 Gas Kitchen...
Feb 14, 2008 | GE Profile JGS968 Gas Kitchen Range
Jan 25, 2008 | GE Profile Spectra JGBP90 Gas Kitchen...
Oct 04, 2016 | GE Profile Spectra JGBP90 Gas Kitchen...
Dec 16, 2014 | GE Profile Spectra JGBP90 Gas Kitchen...
11,682 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: