Question about Omega 1000 Juice Extractor

Open Question

Latch arm replacement - Omega 1000 Juice Extractor

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cannot remove the broken latch arm on my Omega 1000 Juice Extractor to replace it with a new latch arm. I have tried to follow vague instructions on the web, but I cannot remove it. Thanks.


It's a real pain and even bigger pain to snap the new one in place. Best way to do it is remove
the 4 screws, not the center one, and separate the base. You will then have access to the
latch arm from within, but remember how everything goes back together again.

Jan 27, 2011 | Omega 1000 Juice Extractor

1 Answer

How do you get the latch arm back in. The bottom is easy but how do you snap the top????


Is this an older juicer and a new latch arm? Surprised you were able to snap it into the base.
If your problem is latching it down because it's a little too snug, file the upper tip a little to
increase the tolerance. Do it to a point where the latch arm will easily slip over the lip of the
cover and then latch it down.

Jan 11, 2011 | Omega 1000 Juice Extractor

1 Answer

The left arm-clamp has come off. It seems to be different from the left arm-clamp. At first I thought I just needed to figure out how to reset the spring, but a neighbor seems to think that the arm was...


They break. The latch arm is one piece, spring and all. So if any part of it is still in the
juicer it's broken. Order a pair from Omega and have them walk you through replacing
them.

Nov 22, 2010 | Omega 1000 Juice Extractor

1 Answer

I got the latch arms for my omega 1000 juicer but only the bottom goes in how do i get top part in


With some difficulty. Sometimes replacement latch arms are not an exact fit for
older models. You may have to file them down a bit so they will snap in place.
Also make sure the fit at the cover is not too snug or else the arm will break again.
Removing the 4 screws on the bottom and separating the base will give you a better
view on what has to be done.

Aug 18, 2010 | Omega 1000 Juice Extractor

1 Answer

Need to replace latch arm omega juicer


First thing to do is call Omega and order a pair
at 1 800 633 3461 and also ask them for tips on
how to remove and install the arm. If your juicer
is older the new arms may not be an exact fit, and
you will have to do a little filing and improvising to
install them. Its helpful to remove the 4 screws on
the bottom to separate the base for better access
and view of the situation.

May 20, 2010 | Omega 1000 Juice Extractor

1 Answer

HI, I have omega 1000 juicer, and the latch arm was broken. I ordered the replacement latch arm online. I received my order today and there is no intruction how to replace it. I looked in omega 1000 manual...


There are no instructions. Call Omega 1 800 633 33461
for advice. Also new arms on an older juicer may not
be an exact fit so you might have to do a little filing
down on the arm to get it to fit. You can remove the
4 screws on the bottom to separate the base and get
a clearer picture of what you have to do. Basically
you have to pry the base of the arm away and push
up to remove it. If you're not handy you may need
some help cause it gets tricky.

May 08, 2010 | Omega 1000 Juice Extractor

2 Answers

Right Arm of Omega Juicer Model 1000 broke off


CALL OMEGA 717 561 1105 THEY HAVE
THE LATCH ARMS. CHEAP. ASK THEM FOR
THERE ARE TO WAYS TO REPLACE THEM.

Jan 25, 2009 | Omega Juicers Juicer 1000 Brand: Omega

2 Answers

How do I replace the latch arm?


I WOULD CALL OMEGA AT 717 561 1105. I REPLACED ONE
ON AN OMEGA 1000 BY REMOVING BOTTOM OF JUICER
TO VIEW LATCH ARM WHERE IT ATTACHES FROM INSIDE
THE HOUSING. YOU CAN FIGURE IT OUT. IT HAS TO BE
PRIED A LITTLE AND SLIPPED UP AND OUT.

Oct 19, 2008 | Omega 4000 Juicer

1 Answer

One bracket broke. Tried to glue it with no success.


IF YOU ARE TALKING ABOUT THE LATCH ARM, YOU CAN BUY THEM FROM OMEGA AT
717 561 1105. TRICKY TO REPLACE. I REMOVED THE BOTTOM OF THE MACHINE AND
GAINED ACCESS THAT WAY. ONCE YOU SEE THE LATCH ARM SUPPORT PRY IT AWAY
FROM THE JUICER AND SLIDE IT OUT. CALL OMEGA THERE ARE 2 WAYS TO REPLACE
THE LATCH.

Sep 29, 2008 | Omega 1000 Juice Extractor

3 Answers

How to replace latch arm for omega 1000 juicer?


Getting the old one out is the hardest part if the arm was broken off like mine. First locate the rectangular part where the arm attaches to the case. If the old arm, or most of it, is still attached, grasp it and pull firmly away from the case until you hear a click. Then, still pulling it away from the case, push it up toward the top of the case until it slides out. If the arm is broken off you have to pry it from the top until you hear the click. I used a small paring knife. Once you get it this far, wedge something like a toothpick behind it to keep it pulled away from the case. Then you need to push this push this part up. It is pretty tight so you might want to use some type of tool, like the blade of a flat screwdriver. Once you get the old one out, putting the new on in is just the reverse of taking the old one out.

Dec 11, 2007 | Omega 1000 Juice Extractor

Not finding what you are looking for?
Omega 1000 Juice Extractor Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Omega Juicers Experts

Andrew Taylor
Andrew Taylor

Level 3 Expert

29384 Answers

eyecam

Level 2 Expert

96 Answers

Tom Chichester

Level 3 Expert

54386 Answers

Are you an Omega Juicer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...