Question about Jandy Aqualink RS6 Pool Only/Spa Only Control System

Open Question

My display says "check min. springs"

Just replaced my c15 salt cell and I'm getting this reading

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 10 Answers

SOURCE: Too much salt in pool (4,100)

the leslies employe is right the only way to get rid of the high salt level is to drain the water i would say drain a 3rd and fill pool and check salt level some salt genarators can not make chlorine at high salt levels or when the water is cold

Posted on May 19, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installed new t-cell and it still says salt level is zero, but the t-cell trips out on high salts,amps. What is the problem?


Depending on the water temperature the actual salt level reading can be inaccurate.

If the water temp is below 65 the reading will sometimes show a lower salt level than the actual level.

Did you recalibrate the power center?

Have you tested the salt level independently?

I would first test the water or have it tested, many pool stores offer this service for free.
It helps to have an accurate reading and not rely on salt test strips.

Once you know the actual salt level you can attemptrecalibrate the system and see what reading you get.

For an aqua rite system you flip the toggle to super chlor, to off and back to auto , wait 5-10 seconds you will hear a click then press the button next to the display , tI'll you see the salt level calibrating.

Oct 25, 2016 | Pool & Spa

1 Answer

EXCEL FORMULA : =SI(C15="*", G15*2.01,B15*C15)


It might be from a Spanish language version of Excel. If so, it would read =if(c15="*",G15*2.01, b15*c15). Obviously, it is a calculation that would depend on the values entered in cells C15, G15 and/or B15.

Feb 25, 2015 | The Computers & Internet

1 Answer

The system keeps showing "no flow" and the hand held asks to check aquapure.


inside aqua pure there is a card hooked to the salt sensor cable there is a button to hold down until a green light shows then see if you get flow if not need new sensor

Jun 20, 2013 | Jandy AQUALINK RS TELELINK KIT

1 Answer

Haywardnet com


bad sensor and clean cell if ok replace both

Jun 01, 2013 | Goldline Salt System Transformer -...

1 Answer

I have recently replace my salt cell after 6 yrs and now I'm getting a "high salt amps reading". The pool is 20,000 gallons and I installed a T-15-Cell. My salt level says 3900ppm but my...


I would first clean the cell according to the manual. If a small amount of conductive material in across the cell plates cleaning may remove it. Then I would use an independent method of testing the salinity. This could be bringing a sample to a pool supply store. I would use this value to determine whether to add or remove salt. One thing that can affect the equipment's indication of "high salt amps reading" is temperature. Many pool owners are having this indication with very high summer temperatures. Using a lower salinity with high temperatures could help. The main thing is to keep the chlorine concentration to between 2 and 4 ppm.so your pool remains sanitary. Make sure the stabilizer level is correct and circulation is good. I hope this helps.

Please vote on this answer. Thank you.

Aug 24, 2011 | Hayward Pool & Spa

1 Answer

My water is cloudy and says low salt. I added 120 lbs and it still beeps low salt. I have a CS8111 saltwater system & filter combo. It is on an above ground pool 24' X 52".


Check the electrolytic cell!!! You will get a low salt alarm if cell has calcium or sodium build up.. If it does, soak, flush and clean with vinegar.. Also, make sure you run the pump only, no chlorinator for 24 hrs to properly disolve the salt you just put in....

Aug 05, 2011 | Intex Automatic Salt Water System for ...

2 Answers

Once a week I've been adding salt (80 lbs) to my pool and again get low salt code (91)....it has been very unusually hot (HTX 110) is this causing the problem and I need to add more?


1st... Check your salt level consentration.. If okay... 2nd, Check you electrolytic cell, may be plugged with white flaky calcium stuff. The white calcium build-up on the cells will cause a low salt alam.

Jul 21, 2011 | Intex Automatic Salt Water System for ...

1 Answer

We just replaced the T-cell for our pool. We were


Sound to me that you added wat to much salt.
If you are using a salt test kit that eads in colors throw it away and get a kit that reads in #.s
If you are using the one with #'s then proceed to getting your water to as close to 3000ppm as possible
Drain 20 % water ad fresh and check again keep doing this ti'll you get close to the 3000ppm

any lower than 2800 and you can read low salt and worse of all you will not produce enough chlorine any higher than 3500 and you will go cloudy and read high

It is my opinion that you were low salt and then adding to much salt put you to far to high

remeber anytime you add salt you should filter only for 12-24 hours to distribute the salt properly so the unit knows what it is reading

While adjusting your salt level clean your new cell with vinegar let it soak for a few hours You should have received a cap to cover one end of the cell while soaking
once cleaned it will not grab hold of the salt water until the generator is turned on

Just remeber 3000ppm

Jul 24, 2010 | Intex Automatic Salt Water System for ...

Not finding what you are looking for?
Jandy Aqualink RS6 Pool Only/Spa Only Control System Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10679 Answers

Bill Jordan

Level 2 Expert

375 Answers

Steve Slater

Level 2 Expert

72 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...