Question about Zanussi ZJD1219 Front Load Washer / Dryer

1 Answer

Zanussi Turbodry 1200 spin problem

Hi, I have a zanussi turbodry 1200 which is around 2 years old.
My wife tells me that everything works fine until the machine trys to enter the spin cycle. The drum starts to rotate then cuts out after a second or two. It then attempts to spin a couple more times then gives up. (Know how it feels). Any advice would be gratefully appreciated.

Paul.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 247 Answers

If this washer is used alot then it will more then likely be the carbon brushes which u will need to take the lid off undue 4screws out where it joins front to the back screws at the back to the bottom and 1screw either side of the bottom where the panels join together behind a little cap which will have an hole in the middle of it to get it out u will then be able to get to the motor to replace the carbon brushes

Posted on Nov 25, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washing machine is zanussi turbodry 1200.Is there an instruction manual I can download?


You should be able to get one from zanussi by going on to there website

Dec 15, 2017 | Zanussi Washing Machines

1 Answer

Stoping under process on every step from begning to ending


its very common for front load washers to have the water pump to freeze up.

ever washed something with sand or little rocks or rubber bands?

flip the washer to the side, then locate the water pump. take the filter and the hoses around the water pump. sometimes the water pump too, to make sure that the fins on the water pump are free and not stuck. put everything together and try the cycle. when the water pump is stuck it will cause the error and will not go into the spin cycle.

Aug 14, 2009 | Zanussi ZJD1219 Front Load Washer / Dryer

1 Answer

Zanussi jetsystem turbodry 1200 door wont open


its the doorcatch,turn power off, remove lid and put hand in machine where doorlock is situated feel about and try open catch, repair or replace?

Jun 24, 2009 | Zanussi ZWF1420W Front Load Washer

1 Answer

WASHING INSTRUCTIONS ZANUSSI ZJD 1285


CLICK HERE



Please download asap - as it is stored on my personal FTP site, and will be removed in 48 hours.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 16, 2009 | Washing Machines

1 Answer

What is E 40 on Zanussi Turbodry 1200?


E40 indicates the doors not closed properly. Sometimes it can be the lock itself or the main control board

Nov 24, 2008 | Zanussi FJS1225W Front Load Washer

1 Answer

Zanusssi jetsystem turbodry 1200


clean out filter, door bottom right, unscrew filter and clean it

Aug 02, 2008 | Zanussi IZ161S Front Load Washer

2 Answers

Zanussi Turbodry jetsystem 1200


hiya
e90 means there is a communication error between the circuit boards inside. remove the plug then take the lid off the machine, remove the block which has the 5 (iirc) blue wires in it and give it a quick squeeze then replace, this should hopefully solve your problem.

hope this helps

please dont forget to rate the helpfulness of this reply, thanks kj

Jul 08, 2008 | Zanussi FJS1225W Front Load Washer

2 Answers

Zanussi turbodry 1050


this may sound silly but check the waste outlet pump electrically, some models are wired up so if the pump fails the water will not enter the machine, this works on the theory that if it fills up it can not empty also check the solenoids for open circuit electrically, double check the water supply to the machine, it may have been fine but you could have kinked the pipe placing the machine back where it should go?

Oct 04, 2007 | Washing Machines

4 Answers

Zanussi jetsystem Turbodry 1200


It appears that you may have a faulty door interlock or a faulty PCB. pcb is not really a DIY job as some boards require proramming on certain versions. Regards Advisor

Oct 30, 2006 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Zanussi ZJD1219 Front Load Washer / Dryer Logo

722 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...