Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Replace a door gasket on a whirlpool duet he washer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,998 Answers

Hello, I think what you are trying to replace is instead termed as the bellows or in laymans terms the rubber boot on the washer that makes the seal with the front panel correct? You can also view this part on this schematic as part number 5 http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=29389401&pkw_=basket&model_id=5136839&NewWindow=1
Unplug The machines power from the wall. The correct way of doing this job is to remove the top cover of the unit by unscrewing the rear screws holding the top panel down and then sliding the panel towards the rear of the machine and removing the panel entirely. Next step would be to the control panel byunscrewing the control screws and seperate the plug connectors that plug the control to the wiring of the unit. You would then have panel number 4 as shown in this diagram that you would next start unscrewing http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=29389401&pkw_=basket&model_id=5136839&NewWindow=1
You would then use a flat screwdriver to pry over the outter metal retaining ring off the bellows and remove the front of the bellows from panel number 4. Note there maybe several small screws on the inside of panel 4 and sometimes to avoid the awkwardness some do remove the door as well from the panel. remove the panel from the machine. You would next remove the retaining ring around the front section of the outter tub by using either a 1/4" or 5/16" nut driver. Note when reinstalling the bellows after installing the new bellows on the tub replace the front panel. When trying to reinstall the front retaining ring that attaches the bellows to the front panel you may require a second set of hands to hold one section of the bellows while using a flat screwdriver and or a putty knife to pry the oppisite end to its proper seating position. If you have any further questions message me back and here is also a step by step video to give you the basic technicque
http://www.youtube.com/watch?v=EFDqUvBgxH4
I await your reply if you have any further questions.
Thank you
Rick

Posted on Jun 17, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
aborcass

Ron Coons

  • 2651 Answers

SOURCE: Door reversal for Whirlpool Duet

there is no reversing the door on the washer. the door on the dryer can be reversed and with the execption of a few of the earlier models no kit is required(even then was just a trim kit). is switching theposition of the 2 appliances an option?? as far as wsher vibrating through house heres a new product receiving great response http://www.keshakeaway.com/servlet/StoreFront

Posted on Mar 13, 2008

Anonymous

  • 135 Answers

SOURCE: Whirlpool Duet Washer GHW9150PWO Have F11

Well du is a door lock error but it can also mean an error with communication to the main control board or ccu. f11 is also a communication error in either the ccu or the mcu ( motor control board)......easiest thing to try is to unplug all your connections to the ccu and plug them back in and try it again.....sometimes a wire harness just may be loose....if that dosent work I would look at replacing the ccu ( central control unit )

Posted on Jul 28, 2008

Anonymous

  • 1 Answer

SOURCE: whirlpool duet washing machine

I work at Whirlpool, and we recommend a product called Affresh to help eliminate washer odor. Affresh washer cleaner tablets break up many of the residues that bacteria, mildew and mold grow on, and it removes them, leaving you a cleaner washing machine.

For a limited time, they’re running a promotion on whirlpool’s website that will get you free shipping on a 3 –pack of Affresh tablets! You just enter EAF822 as the promo code, and they’ll ship you the packet at no cost to you!

Posted on Aug 26, 2008

Bill Dozier

  • 262 Answers

SOURCE: Front door gasket whirlpool duet washer

before replacing run a empty load with alot of bleach in it and then clean boot with a mold cleaner like kitchen cleaner w/bleach replacing the boot isnt something you want to do unless you have to do it (not easy) and the cost of the boot if you need any more help let me know and i will guide you thru the process of the boot
bill

Posted on Jan 08, 2009

Anonymous

  • 1 Answer

SOURCE: Black mold growing on rubber

The solution? Plain old bleach.
Scrub rubber seal on door. Run the bleach through the machine once a month to keep clean.

Keep door open after each wash to ensure that it dries out properly.

d

Posted on Mar 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just noticed a large pool of water under the duet washer. it is not coming from the supply lines- It only appears when the washer is running. I see it leaking down the side (just above the pedestal). ...


door boot/gasket is bad replace and problem solved.but first take the front panel below door off and make sure before you buy a door boot but if it is leaking you can tell by wipeing finger below door while running usually.

Nov 02, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Front door leaks


The door gasket is bad this page will help http://www.appliance-repair-it.com/GE-front-loader-washer.html

I know the page says GE front loader but replacing the door gasket is the same.

Oct 05, 2010 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Washer will not turn on. I tried all the usual


Hello,Copy and paste this service manual.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/6545d78b3f479480852571650061b1ba/$FILE/8178558.pdf
Thanks

May 23, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

How do I change the door gasket on a Whirlpool Duet washing machine model WFW8300SW03 I have the new part


The following link explains step-by-step how to replace the door bellow on a Whirlpool Duet series front loader:

http://www.fixya.com/support/r3574186-installing_a_door_bellow_on_a_front_load

If you have any questions about this repair, please post back and let me know. I hope this helps you.

NOTE: You can view helpful exploded view diagrams of your washer at searspartsdirect.com for assistance as well.

Apr 22, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Front Loading Door leaking water


The most common cause for a front loading washer to leak from the front door is a torn or detached gasket where that gasket attached to the machine.
Open the door and begin to pull the gasket away from the opening. Look for any problems. If you find a place where the gasket is not firmly secured to the opening, you can list that area up and glue (even with super glue) the gasket back down to the metal opening.
If you find gasket damage, it will need to be replaced.

Jan 03, 2010 | Whirlpool Duet Sport HT WFW8400TE Washer

1 Answer

The gasket has cracked on the bottom and leaks. I have bought the new door/drum gasket. Where can I find instructions as to how to replace this large gasket/ring that stops water from leaking out the door


This is not to my credit, but I found it on Fix-it--


here is an online manual ,as txt url wraps around you may have to copy paste it .

http://adcxns1.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/eab852a13fbc842085256aa200643dd6/$FILE/Duet%20Job%20Aid.pdf

Nov 01, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

How do you change front door gasket


The following link explains step-by-step how to replace the door gasket (bellow) on a Whirpool Duet:

http://www.fixya.com/support/r385211-replacing_door_bellow_whirlpool_duet

If you have any questions about this repair, or require additional assistance, please let me know. I hope this helps you.

Aug 14, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Front door gasket whirlpool duet washer


before replacing run a empty load with alot of bleach in it and then clean boot with a mold cleaner like kitchen cleaner w/bleach replacing the boot isnt something you want to do unless you have to do it (not easy) and the cost of the boot if you need any more help let me know and i will guide you thru the process of the boot
bill

Jan 08, 2009 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

897 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...