Question about Asko W6222 Top Load Washer

1 Answer

My ASKO W6222 won't drain

Hi there, my asko W6222 won't drain after it finishes its cycle. It spins and everything ok, however clothes are still really wet afterwards and it fills up with water and leaks over the edge. I have emptied the drainage pump and removed all the coins that collected there but it didn't fix the problem. Not sure what else to do. Can somebody assist?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Asko Master
  • 1,344 Answers

Sounds like the inlet water valve is not seated properly and is letting water in when it shouldn't .

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Posted on Jun 20, 2012

Ad

4 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Asko help me

  • 1 Answer

SOURCE: I have an asko 11505

My Asko 11505 washer fills only a little water then shuts off. If I drain the washer with the drain hose from under the machine, then the machine will start up and fill enough water to fill the hose again, then shut off.

Posted on Apr 05, 2010

sonicboomele

sonic boom electronics

  • 1557 Answers

SOURCE: Hi, I have the ASKO W6222 front load washer, my

if the valve was stuck open it would run all the time the washer was on i would say that there is a power short running to the valve turning it on when not selected

sonic boom electronics australia

Posted on Jan 04, 2011

john_cross

  • 6277 Answers

SOURCE: getting f3 error message checked

Hi from retired Englishman in SW France,
Here is an extract of my guidance notes on checking filter and motor. Try the last paragraph in particular-
POWER OFF FIRST
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Posted on Jul 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Start matsui washing machine


Check the washer drain hose for clogs.

Jun 19, 2017 | Washing Machines

1 Answer

Why is it that my washer is not completing the spin cycle,it is still very wet when it stop??


Hello there and welcome to fixya
The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these: Motor coupler
To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning:
If it's spinning when you lift the lid, the coupler is fine.
If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.
Spin cycle
If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.
Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.
Siphoning
If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.
Water-inlet valve
Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.


Sep 12, 2011 | GE Washing Machines

1 Answer

Hi, i have an AEG Lavamat 1100. Although the machine runs through the spin cycle, and shows the wash cycle as being finished, when i open the door there is still water in the bottom of the machine and the...


Hi bwileman435,

It may not be draining well, because it is dirty, did you clean the Drain Pump filter?

Please follow my below Tip on how to do it:

ACCESS, DRAIN & CLEAN THE DRAIN PUMP FILTER

Kind Regards d")

* If this solution helped you, please rate it

Aug 05, 2011 | AEG Washing Machines

1 Answer

I have a Whirlpool WFC7500V Front Load Washer and after the load is done the clothes are still soaking wet, is there a step i am missing why are the clothes still really wet. Do i need to drain or is the...


What spin cycle are you using? Try a faster spin option. (The wrinkle release setting uses more water and a lower spin speed.)
Try putting fewer items in a load in the futute and make sure it isn't unbalanced. (One really heavy item could imbalance the load and shift the spin efficiency.) Redistribute the clothes and run a Drain/Spin cycle.
Make sure to use HE detergent (don't use more than the recommended amount of detergent).

The other issue to check is if the machine is draining properly. Check that the drain hose isn't clogged. Also check the voltage at the washer - low voltage will result in a slower spin cycle. To correct this, you probably will want to call an electrician.

I hope this helps.

Cindy Wells

May 05, 2011 | Whirlpool Washing Machines

1 Answer

Clothes wet after spin


Hi, if clothes are wet after spinning, check.......
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning: If it's spinning when you lift the lid, the coupler is fine. If it isn't spinning--and your machine was produced by Whirlpool you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.

Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag), a worn clutch (GE/Hotpoint), or a worn motor pulley or tub bearing. Replace the applicable component. Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

Apr 13, 2011 | Whirlpool LSR8433K Top Load Washer

2 Answers

Hi, I have the ASKO W6222 front load washer, my


if the valve was stuck open it would run all the time the washer was on i would say that there is a power short running to the valve turning it on when not selected

sonic boom electronics australia

Jan 04, 2011 | Asko W6222 Top Load Washer

1 Answer

How do you open the door, and how do you get the clothes not sopping wet when the wash cycle is done?


HI- If the clothes are coming out wet then there is either a problem with the spin cycle or drain pump. The door won't open if the washer senses there is too much water in the machine. Try doing a dedicated spin again the see if the door will open. Your drain pump may also be clogged. There is a little door at the bottom front of the machine. Open this (pry carefully open with a butter knife) and you will see a plastic plug that can be unscrewed (counter clockwise), this is the pump filter. Be prepared to catch the water that will come out with a pan and have some towels ready, sometimes there is a lot of water. Once you get the filter out clean it out and check for any loose change inside the pump. Screw it back in carefully and tight and be careful not to strip the threads. Run a rinse and spin once it's all back together and see if it drains ok. If it still is not draining you probably need a new pump. There are very few Asko Techs around so you may have some trouble getting someone out. As well, call Asko customer service, they have really good techs that can help you over the phone. Good luck.

Sep 23, 2010 | Asko W6021 Front Load Washer

1 Answer

I have an asko 11505 clothes washer. For some reason, it is not going through all of the spinning cycle, it spins for a short time, then stops abrutely. I cleaned the coin stop, cleaned out all water...


My Asko 11505 washer fills only a little water then shuts off. If I drain the washer with the drain hose from under the machine, then the machine will start up and fill enough water to fill the hose again, then shut off.

Oct 19, 2009 | Asko Washing Machines

Not finding what you are looking for?

Open Questions:

See all Asko W6222 Top Load Washer Questions

Asko W6222 Top Load Washer Logo

785 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

ROB

Level 3 Expert

858 Answers

Lollo Pop

Level 2 Expert

134 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...