Question about Jandy Pool & Spa

Open Question

Installing a jandy ST24-T filter

How to install a Jandy ST24-T sand filter

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

james aurienne

  • 93 Answers

SOURCE: jandy 1.5 hp pump with jandy ae 2500 heat pump low flow

IF FILTER CUP IS NOT FILLING COMPLETLY THERE IS A AIR LEAK CHECK ALL HOSES AND FILTER FITTINGS

Posted on Jun 10, 2009

Ad

Anonymous

  • 16 Answers

SOURCE: Jandy pool pump will not prime it is a Jandy plus HP model PHPM 2.0

make sure pool is full of water
check skimmer weir doors and make sure not stuck in up position
fill pump basket with water and try to prime

if that doesn't work

replace diffuser oring

http://www.jandy-downloads.com/pdfs/PHP_Manual.pdf

Posted on Jan 16, 2010

Dale Cobb

  • 366 Answers

SOURCE: jandt filter leak

it depends, if it's leaking due to a crack on a structural part of the filter such as the tank itself, then yes, the entire tank will need replaced.

Posted on Feb 20, 2010

john224

John Prohaska

  • 1378 Answers

SOURCE: JANDY JHPU 2.5 PUMP is making a noise.

Thank you for posting your question here on Fixya.com.

Your motor bearings are failing. It is most often caused by a leaking pump seal. It is a relatively inexpensive repair if it is caught early enough; before the shaft is damaged from the corrosive water eating into the steel. Take it to a local electric motor repair shop for inspection. It will likely need a set of 203 bearings for the motor and a mechanical seal for the pump. All told, depending on the labor rates, it should be less than $75.

If this answer does not fix your problem, please comment with additional details prior to rating the answer. Positive feedback is appreciated once your problem is solved!

John

Posted on Mar 01, 2010

Anonymous

  • 351 Answers

SOURCE: Jandy/Stealth Pool Pump motot

Hi .. If ypou are gtetting air in the basket, then ytou have a leak somewhere in the system. start by closing off the skimmer, bottom, cleaner one at a time and see when the air stops gettingt in. Is there enough water level to cover the skimmer? have you checked the seal on the strainer at the pump? you might be able top hear hissing if it is at the pump.

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My jandy control panel is locked. how do I get it unlocked


About 4,480 results (0.49 seconds) Search Results

    [PDF]AquaLink RS All Button and OneTouch ... - Jandy

    www.jandy.com/~/media/zodiac/global/downloads/0748.../6919.pdf
    Jandy Valve Actuator . .... If power is then interrupted, the controller will lock up. ...process, which can display its current status on the indoor control panel. Use the following steps to get to this "diagnostics" information: ...... lect Device to unlock.

    [PDF]Jandy Legacy WLRZ Control Quick Start Guide

    www.jandy.com/~/media/zodiac/global/downloads/h/h0346600.pdf
    The Legacy WLRZ will heat the pool or spa only when the filtration system is running and the ... DISPLAY LIGHT: Controller lights can be set ON, OFF, or to ... Make sure the control is in the ON mode ... To unlock, press and hold the up and.

    Clock" Mode; Locking/unlocking The Keypad; Remote ...

    www.manualslib.com > ... > LJ > Installation and operation manual
    Jandy LJ Manual Online: Clock'' Mode, Locking/unlocking The Keypad, Remote Control Operation, ... display of the controller will show the time set for the.

    Jandy AQUALINK RS TELELINK KIT Locked - Questions ...

    www.fixya.com > ... > Jandy > Jandy AQUALINK RS TELELINK KIT

Feb 03, 2016 | Jandy Pool & Spa

2 Answers

How to replace sand in a jandy st24-t


there is a nice big o ring between the valve and the filter body. chances are that it is dried out and holding fast. it will take some muscle to separate the two but it can be done. be prepared to change that o ring on re-assembly.
here is a breakout plan to help you visualize
ST18 ST 20 ST24

Sep 01, 2014 | Pool & Spa

2 Answers

Jandy PDA-PS4 lost link to salt system?? There is no more


go to system setup find aqua pure up setting from 0 to something and it will apear

May 27, 2012 | Jandy Aqualink Pda Ps4 Wireless Handheld...

1 Answer

Directions on changing sand in sand filter model number ST24-T


remove top shop vac all sand out and replace(dont get any sand down verticle pipe

May 26, 2012 | Jandy Pool & Spa

1 Answer

Where is the filter located in jandy lite 2 pool heater


its your pool's sand or cartridge filter!!!! heater has no filter

May 24, 2012 | Jandy Lite 2 Natural Gas Pilot Light...

1 Answer

Jandt filter leak


it depends, if it's leaking due to a crack on a structural part of the filter such as the tank itself, then yes, the entire tank will need replaced.

Feb 18, 2010 | Jandy PUMP SHAFT SEAL - FITS PUMPS

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10744 Answers

Bill Jordan

Level 2 Expert

375 Answers

Steve Slater

Level 2 Expert

72 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...