Question about D-Link ADSL2/2+ Modem/Wireless Router 4-Port Switch, 802.11g, QoS (DSL-2640B)

1 Answer

Not able to open settings page (DLINK (WBR-1310)

I AM USING DLINK WBR-1310 ROUTER. I AM NOT ABLE TO OPEN SETTINGS PAGE.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • D-Link Master
  • 32,281 Answers

If the default password on the D-Link has been changed then-
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to3.05)Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)You can now change the default admin password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Posted on Jul 02, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 101 Answers

SOURCE: i can't access ther router using 192.168.0.1

Hi Wafula,

Unplug the Dlink, wait 2 min, and plug it back in. If that work, on the back is a small hole, marked RESET. Using a pencil, or straightne out a large paperclip, press that the button inside gently. Hold it for 30 sec. Release and unplug the unit. Shut down the whole network. "Starting from the wall", power up the modem, wait 2 min, power up the Dlink, and power up your machine. Your Dlink should be at default now. Remember to reset you security, change the password, etc.
I have had to do this several times, sometimes unplugging the power, and plugging it back while holding the button. (Got 3 hand?)
Good luck!

Posted on Jan 10, 2008

acdr

kishor khatri

  • 1913 Answers

SOURCE: dlink dir-300 wireless router connection problem!

first coonect your wifi router witjh your laptop with ether net then go to this link
http://192.168.0.1
then type user :admin and password also admin or blank
then go to dhcp then enbale it with auto .
then disconnect your cable from laptop.
then go to my network places then find wireless network then simply conect your network.
thtas it.

Posted on Nov 10, 2008

Anonymous

  • 2 Answers

SOURCE: Unable to access DLink WBR 2310 Configuration page

Reset the router first, press the reset pinhole on the back for 10 seconds using a paper clip, don't press it too much or it will mess up the settings of the router. then try to access again the configuration page.

Posted on Feb 10, 2009

fougzki

  • 700 Answers

SOURCE: Not able to configure and connect to internet using router

Manually configure the setting in your LAN, this could help.

Connect a LAN cable between LAN1 of your router then to the LAN port of your computer. Power the router.

Goto Lan settings, highlight TCP/IP, then click properties.

In your lan settings manually input IP address 192.168.0.52, Subnet 255.255.255.0, gateway 192.168.0.1

You can input also the DNS number of your IP.

Then open web browser type in the address bar 192.168.0.1. You should go straight thru router utility setup security log in.

This can also be set wirelessly. Leave comments if I miss something.

Posted on May 18, 2009

Anonymous

  • 1383 Answers

SOURCE: dlink wbr-2310 router no wireless working

you have to change your channelk type in your wi fi router.
For that access your router with following link

http://192.168.1.1 or
http://192.168.0.1

if you have belkin router
http://192.168.2.1

type user name as "admin" and password is "admin" or blank or "password"

then go to wi fi ->advanced setup chang channel type 4 ,6 ,11
change chanel type 1 by 1 and check signal strength.
everyt time save settings and restart both computer and router after save settings.

Thanks for using fixya.
Please rate this solution if it helps.

Posted on Jul 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to secure my wireless connection network. I have a iMac computer an a Dlink WBR 1310. How do I configure a Password to prevent intruders from using my connection?


First you will need to find the local IP address of your router. It should look something like "192.168.0.1" You might be able to find it in either your router manual or on the bottom of the router itself.
Then make sure your computer is connected to the router via wireless or ethernet cable.
Next, open your browser and type in the IP address into the address bar. It should take you to a setup page that looks a lot like a website. Find the "wireless security" tab and select a security protocol. I recommend using either WPA or WPA2. Now you can set a password. Finally, there should be "save" button on the page. Click it, then wait for your router to reboot and your network is now secure.

Jul 31, 2011 | D-Link 802.11g Wireless Router WBR-1310...

2 Answers

I have lost my disk and need to program a password, due to nieghbours using my wireless. How do I do this


Hi evan,

Basically you don't need a CD if you want to change the password or put a password on the network all you need to do is to access the Wireless Settings Page of the Router and put or change the Network Key. To access your router you need a working computer connected to the router then open a Browser then type 192.168.0.1. the Username is admin and the password is blank. Go the the Wireless Settings Page and under Wireless Security Mode you can change the Security Mode to either WEP, WPA or WPA2 then input your desired password.

Rate me if this helps so i can help others.

Thanks for using Fixya.

Feb 04, 2011 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

I have Dlink WBR 1310 Router which I had set up but now after up grading my laptop I cannot get the set up done and Router is not provided by the ISP I do not remeber my ISP ID/PW and router setup wizard...


Did you try to reset the router ? Once you reset the router, you will lose all the settings of the router and you can set up the router from the scratch.
Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for step by step by instructions

May 19, 2010 | D-Link 802.11g Wireless Router WBR-1310...

2 Answers

My WBR-1310 doesn't do wireless to my laptop.


theres a couple of version of this router http://www.dlink.com/products/default.aspx?pid=WBR-1310&tab=3 I'm using the manual from here http://www.dlink.com/products/?tab=3&pid=WBR-1310&rev=WBR-1310
on a working PC download and install this program http://www.xirrus.com/library/wifitools.php this will detect all the wireless signals being broadcast - see if the router is actually broadcasting - if it is detected on your PC then it may be that 1) the firewall is blocking access or 2) the security code is entered wrong - -log into the router and remove the wireless security and see if you can now detect

Mar 18, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Do not know the network security key


Is there any computer online using the router.
If yes then you can open the router set up page on that computer.
router set up page is the page where you can check all the router settings.
Click Here for more information about the routers and network

Jan 30, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

My laptop say i am connected with internet access but it is not; when i check network magic there is a red x through router and laptop; how do i fix this...have unplugged and reset but nothing works; seems...


uninstall the network magic . that software has lot of issues.
You can uninstall the program and try to connect using the windows utility. that is very easy and that works properly.
Is there any computer connected to the router with the cable. If yes then open the router set up page and check the wireless settings of the router.
Click here for more information about the router and network

Jan 13, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Need to download a cd for my WBR-1310 wireless router


If you can't find a CD just visit the D-Link support page for your router and you can download most of the stuff that was on the CD. This would include the product manual, the latest firmware and helpful FAQ's.

This page is located at http://www.dlink.com/products/?pid=WBR-1310 .

Oct 12, 2009 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

D-LINK WBR 1310 ROUTER


Go the router setup page, 192.168.0.1, type admin as the user name and password as the password (default, if you have changed these use your login info).
Then on the wireless page change the SSID (router name).
You can also add a security key on this page.

http://support.dlink.com/emulators/wbr1310_revA/wireless.htm

more info from D-Link:

http://www.dlink.com/products/support.asp?pid=474&pv=96&sec=1

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Apr 12, 2009 | D-Link 802.11g Wireless Router WBR-1310...

3 Answers

I forgot the username of dlink wbr-1310 wireless router


Hi there,

As an initial info try to do a hard reset on the unit, this process will restore the system into a original settings. you can find the reset switch on either on the left of right sight of your router.

or

you may visit this SITE to recover again your current password without erasing or removing the current settings made.

Reset Password.

Hope this idea helps you.

Thank you for using fixya.

Nov 20, 2008 | D-Link 802.11g Wireless Router WBR-1310...

Not finding what you are looking for?
D-Link ADSL2/2+ Modem/Wireless Router 4-Port Switch, 802.11g, QoS (DSL-2640B) Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...