Question about Office Equipment & Supplies

1 Answer

Hp 1007 laser printer on position but no initialise

Printer remains on but no initialise. also printer green led on when door is open.

Posted by on

  • manivannan Aug 14, 2012

    Hp 1007 laser printer on position but no initialise pls ply me



1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

Just open the printer and check all the censor whether it got struck or any small paper will be inside.other than there is no problem in the printer

Posted on Aug 09, 2012

  • leomichael
    leomichael Aug 09, 2012

    just open the printer and check all the censor whether it got struck or any small paper will be inside.other than there is no problem in the printer



6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 4338 Answers

SOURCE: All LED blinking

try to reset the printer:

- Machine off
- Front cover OPEN
- Switch on the machine while holding down the “GO” button
- Check that the TONER/DRUM/PAPER leds are lighted
- Release the “GO” button and check that all the leds are off
- Press the “GO” button 2 times
- Close the FRONTCOVER
In case of all the leds are flashing on/off, that means the printer hardware fails somewhere. To find out what section fails, you can press down the “go” button and a led will go on.

Toner + Paper >> MAIN MOTOR FAIL

If you cannot determine wich led goes on,it seems that the main board is broken.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

I’m happy to assist further over the phone at

Posted on Jan 07, 2009


Gerry Millward

  • 353 Answers

SOURCE: we r have epson c45 stylus printer.after initialise red and green

The Waste Ink Pads are deemed to be saturated and should be replaced. You can overcome this problem temporarily bu using the SSC utility - download from

and reset the Protection Counter. However, remember that eventually ink will overflow from the waste ink area and make a dreadful mess, so you must change the waste ink pads before this happens. This requires the disassembly of the printer. A copy of the service manual is available from a number of sellers - just Google "Epson C45 Service Manual.

Posted on Jan 31, 2009


  • 21 Answers

SOURCE: hp laserjet printer 1007 windows 98 driver

goto click on "drivers & software" type model of printer and it will take you to the selection of what software you are using so you can download your driver.

Posted on May 26, 2009


  • 1 Answer

SOURCE: I am wanting HP 1007 pritner driver to install

I am wanting HP 1007 printer driver to install

Posted on Jul 20, 2009


  • 60 Answers

SOURCE: i have face one problem with olivtti pr2e passbook


Posted on Feb 02, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I fix a LaserJet HP2015 printer? The triangle is flashing amber and the Go button light is green.

Don't you just love HP? Since your machine is no longer under warranty they will not help you.

Best bet is to replace or jump the cartridge door switch and see what happens. My guess is that it is stuck.

Nov 10, 2015 | HP LaserJet P2015 Laser Printer

1 Answer

How do I load ink and toner in hp laserjet 1100

By load the toner, if you mean inserting the toner cartridge.Then i will give you instructions.In laser toner printer, there is toner cartridge, and not ink jet cartridge.In laser toner cartridges, there is a black color toner power and it does have any liquid ink, which ink jet cartridges have.To remove the laser toner cartridge from hp laser jet 1100 printer, its simple.The front door open and old toner cartridge comes out.Just pull the front door towards you.While inserting cartridge.If you have problem, then take note that, sticker side of the cartridge is towards you.On the cartridge there is a rectangle flap, which you hold in your hand.This is meant for holding the cartridge, while removing and inserting cartridge.The stick side will be in your side.There is a green color drum, the drum side will be on opposite site.-------------- Still any problem.Keep updated.But i think that will help.Thanks.Helpmech.

Mar 25, 2011 | HP LaserJet 1100 Printer

2 Answers

I get an error in HP LaserJet 4345 MFP printer, 49.ff95 error, Tunr off and the turn on

a 49.xxxx error on an HP means that there is an issue with one or more hard disks. you can try to re-initialise the hard disk(s) by rebooting the printer while holding the green button. when the three leds are lit, release the green button, and navigate using the numerical buttons until you see "initialise hard disks" on the display of the printer. confirm by pressing the green button again. if all goes well, your printer will take two minutes longer than usual to boot. if you still get the same error afterwards, you need to replace the disk.

Apr 21, 2010 | HP LaserJet M4345 MultiFunction Printer

2 Answers

I am wanting HP 1007 pritner driver to install

I am wanting HP 1007 printer driver to install

Jun 20, 2009 | Office Equipment & Supplies

4 Answers

Hp laserjet printer 1007 windows 98 driver

I want to install hp laserjet printer 1007 in windows 98 operating system.

Oct 17, 2008 | Intel Motherboard

1 Answer

Printer not printing

Formatter internal RAM or ROM error.

Apr 23, 2008 | HP LaserJet 1200 Printer

4 Answers

Hp laserjet 1320 problem

This is an error state that is not described at HP site.

Try to do a hard reset:

1) Turn off the printer

2) Press and hold down the green GO button

3) Turn the printer on and continue to hold the green GO button for at least 5 seconds, but not longer than 15 seconds. During the process, the Attention LED will turn on.

4) Release the GO button.NOTE: If both the Attention light and the Ready LEDs turn on before the GO button is released, the cold reset procedure must be started over at step 1.

5) The printer LEDs begin cycling. The cold reset process runs until completion and the printer returns to the Ready state.

Hope it will help you

Jan 24, 2008 | HP LaserJet 1320 Printer

1 Answer


you,have an error on printer ,check all ,paper,cartridge,doors if all is ok, then you must to call a service man

Jun 27, 2006 | Samsung ML 4600 Laser Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts


Level 3 Expert

2239 Answers


Level 3 Expert

13434 Answers


Level 3 Expert

85223 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides