Question about Denon AVR-2312CI

1 Answer

Restarting avr-2312 Hi, I bought a Denon 2312 and sometimes after i turn it on after 4-5 seconds it restart and repeated all the time, the only way is to turn it off 1-2 hours . I disconnect everything except power supply but the same.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I've had THE SAME PROBLEM ! Neither official servise, nor internet could help me. The solution was problem with POWER CABLE! When tested it by TESTER it was ok, with no sign of a problem. I've tested everithing byt nothing could help me :) After all test I've noticed that when I've touched the power cable the problem occurred. After changing the power cable everithin WAS GREAT.

Posted on Mar 06, 2013

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: Powers turns on then off

See: http://www.denon.ca/hapdfs/avr2105mane.pdf, page 72. In my case, the problem was a connector between my receiver and television. I unplugged it from my receiver and it now works.

Posted on Jul 08, 2007

Rob Galayda

  • 54 Answers

SOURCE: Denon AVR-1601

This is a very common problem with denon receivers of the 2001-2-3 vintage. On almost every one, there are 4 little "surge" resistors in the power supply. These werent quite robust enough from the factory and one day would just burn open for no reason. Well, actually there is a reason, the "surge" that happens every time you power the unit up eventually weakens the resistors and then they pop. You need to take this to a denon service shop as I GUARANTEE they have seen this before. They need to check resistors in the picture, locarde above the **** rectangular connector. Resistors numbers R141, 142, 148, 149: 75f69d7.jpg These resistors when measured, should be less than 10 ohms each. If they are more, then they are blown. If they are blown, then have the shop check the channels for blown output transistors. If the outputs are OK, then these resistors should be replaced with 1 ohm 1/2 watt metal -film flameproof resistors. You might need to be prepared for a large bill, because the entire unit must come apart to replace the resistors, however, just checking them takes only about 10 minutes... Good luck and don't try this at home. Rob

Posted on Apr 08, 2008

SOURCE: Denon avr-1804 its turns back after 5 sec

Disconnect all speaker wires on back and then turn on. If it happens again, it's most likely a power supply problem. If it doesn't happen again, it was probably crossed speaker wires.

Posted on Dec 28, 2009

budgie140

Ian Summerfield

  • 502 Answers

SOURCE: problem denon avr 1910

most electrical units have a fuse inside,try taking cover off and checking for blown fuse,or,take it to radio repair shop.My Harmon Kardon stopped after 3 years,and the report said the unit that failed was quite a common problem for the modern multi channel amps,quite cheap to fix..All my tips are free

Posted on Jul 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Denon 2910 CD player malfunctions


is this happening with all the cds??
the case may be with the cd sometime..where the tracks wouldnt have been properly completed...

Jul 13, 2008 | Denon DVD-2900 DVD Player

1 Answer

After battery recconected in 1991 ford laser how do i enter code to restart radio


The instructions are usually these

Ford Code EntryInstructions Once the unit has been turned on the display will show 'CODE - - - -' Press preset [ 1 ] repeatedly for the first digit Press preset [ 2 ] repeatedly for the second digit Press preset [ 3 ] repeatedly for the third digit Press preset [ 4 ] repeatedly for the third digit To save the code press the [ 5 ] key to accept.(sometimes it`s the [ 6 ] key to accept
The set should now operate.

Mar 10, 2011 | Car Audio & Video

1 Answer

I bought a ford ranger 2006 the radio is blocked but they gave me the code i just dont know how to enter the code into the radio


Ford Code EntryInstructions Once the unit has been turned on the display will show 'CODE - - - -' Press preset [ 1 ] repeatedly for the first digit Press preset [ 2 ] repeatedly for the second digit Press preset [ 3 ] repeatedly for the third digit Press preset [ 4 ] repeatedly for the third digit To save the code press the [ 5 ] key to accept.(Sometimes this is [ 6 ] key to accept)
The set should now operate.

Jan 29, 2011 | Car Audio & Video

2 Answers

How do you enter the radio code, for a siemens vdo cdr 500. please can you advise


Vauxhall Delco CDR 500 Code Entry
Press and hold the [ AS ] key and switch on.

'SAFE' will display followed by '10 - - - - '

Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the third digit

To save the code press the [ AS ] key to accept

Sep 01, 2010 | Car Audio & Video

1 Answer

Denon PMA250II Amp playing up.


suspect caps in speaker relay protection ccts

Jan 22, 2010 | Audio Players & Recorders

1 Answer

My printer is not working , power cable is connected but no indication of power in the printer. i have already bought a new adapter consulting an electrition


Hi,
As you have tried with new Adapter, try to connect the printer directly to the wall jack and see if it is turning on.

If the unit is not turning on then perform these steps:
Follow the steps below to power cycle the all-in-one:
1. Shutdown your computer.
2. Verify that the unit is switched on. Unplug the all-in-one from
power and disconnect the connection port.
3. Wait 30 seconds.
4. Plug in the power only.
5. Repeat steps 2-4 two more times.
6. On the third time after plugging the unit into power, reconnect
the connection port from the all-in-one to your computer.
7. Restart your computer and check the functionality.

If the issue persists then Click here and perform the steps in the web link document.

Dec 26, 2009 | HP Office Equipment & Supplies

1 Answer

Denon asd-3w dock---do you need an ipod in order to use the dock?


Hi, You don't need an iPod to get the network audio to work. This sounds like the power supply is faulty - is ther lots of clicking coming from the unit?

Feb 07, 2009 | Denon ASD3W IPod Networking Dock Docking...

1 Answer

No sound/test tone front front right channel


1-make a reset to your system.2-repeat your speaker setup.3-confirm that you assign your sysem for 5 chanell surround system.-4-change the cables between left and right front speakers if the trouble go to left channel you will have a problem in receiver itself-if the problem exict you will have a problem in speaker itself(cable or speaker)

Sep 30, 2008 | Audio Players & Recorders

Not finding what you are looking for?
Denon AVR-2312CI Logo

Related Topics:

537 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76177 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...