Question about Intel Motherboard

1 Answer

D945gccr MB NO DISPLAY I GUESS ITS BIOS PROBLEM

I hav a d945gccr MB . and the fan and led on th MB r working but i m not getting th Display . I removed th ram and check'd its giveing th bip sound .but when i fix th ram and on THER IS NO DISPLAY Can any one solve this

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Intel Master
  • 5,660 Answers

Maltesh,

1) IF ALL of the LED (Lights) were on they would use less than 1 Watt of power.

2) EACH fan uses 2 to 3 Watts of power.

3) A typical Processor can use 51 to 125 Watts of power.

Intel D945GCCR motherboard?
Can use up to an Intel Core2 Duo E4700, (800MHz FSB), according to Intel Support,

http://processormatch.intel.com/CompDB/SearchResult.aspx?Boardname=d945gccr

An Intel Core2 Duo E4700 can use up to 65 Watts,

http://en.wikipedia.org/wiki/List_of_Intel_Core_2_microprocessors#.22Allendale.22.2C_.22Conroe.22_.2865_nm.29

Check the Power Supply.
A Power Supply with a weak voltage power rail, will have plenty of power to light LED's, and maybe spin fans, but Not enough power to turn the Processor on.

No processor, no computer.
The computer isn't generating a video signal.
No Signal to the monitor.

Do you have access to a multimeter, or DC Volt meter?
Test the three Low DC voltages coming out of the Power Supply.
A) 3.3 Volt power rail
B) 5 Volt power rail
C) 12 Volt power rail (ALL are DC voltage)

[ In comparison two D cell flashlight batteries store 3 Volts DC ]

Need guidance with testing post back in a Comment.

Or if you have a KNOWN to be good, and Compatible power supply, that you can borrow for a test, try it.

Regards,
joecoolvette

Posted on Aug 14, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: intel 845 gvsr no display

Intel d845 gvsr no display ,but the ram is ok when i incerted the ram there is no beep and there is no sound. may be bios corupted and how to solve the problem

Posted on Apr 17, 2008

Anonymous

  • 447 Answers

SOURCE: My Intel D102GGC and Mercury 915GLV motherboard not wake up

Is this new ram or have you used it in this machine previously?

A couple of things can cause what you describe, one of them being the wrong voltage of ram. This page contains the list of memory that your system can use, check the part number on your current ram in google to find out what voltage it runs at (the recommended voltage for your board is 1.8v).

Other than that you may want to do a CMOS reset by changing the jumper block (should be described in your mobo manual), powering the machine on briefly, power it down (unplug) and return the jumper to it's original location. Now try to post the machine.

Posted on Mar 06, 2009

bravsman

Joel Cruz

  • 94 Answers

SOURCE: NO BEEP, NO DISPLAY EVEN REMOVING OF RAM.

are you using socket 478 motherboard or socket lg775 motherboard? if lg775 mobo you using try to remove the cpu heat sink and put it back again make you put correctly lock it perfectly and try to switch it on

Posted on Mar 12, 2009

Anonymous

  • 6 Answers

SOURCE: D945GCCR problem

try to change your flex and then point correctly the flex into hard,floppy and cd-rom.. you can check also at the back of hard disk there you can the procedure..

Posted on Jun 23, 2009

Anonymous

  • 259 Answers

SOURCE: Mother bord and processor and RAM is working , but No-display

chnge the hdd

Posted on Jul 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No display


did you try to overclock ?

Mar 30, 2010 | Intel D945GCCR Motherboard

1 Answer

The motherboard not give any display !


last 2 things to do
1.remove the cmos battery
2.remove the cmos jumper.
remove power cable from power supply.
3.wait for 2 to 3 mins

4.put the jumper back to the correct position usually pin one and pin 2
5.try to start the mb if ok
ok

Nov 13, 2009 | ASUS P5N32-SLI Deluxe Motherboard

1 Answer

Asus p5s800-vm MB has complete power lets monitor know


Disconnect the hard drives, cd/dvd drives and any expansion boards you have plugged into the mainboard. We want to remove as much as possible to see if we can eliminate the problem.Using the onboard video, start it up again, and see if it comes up. If it does, then its one of the items you disconnected. Power down and reattach one of the disconnected items and power up again. Did it come up? Keep in mind that we want to see the bios start up screen. Once you have attached all the items you will have found the bad component. Replace it. But lets say you didn't get a good system when you disconnected everything. Well, that narrows down the suspected bad items to: the mainboard, the power supply, the memory, or the cpu. The power supply has many voltages coming out of it, keep in mind that the drives, cd/dvd rom drives and fans use 12 volts for spin up. There are 3 other voltages used by the mainboard. I would replace the power supply next with a known good one. Then it gets a little costlier, the memory, then the cpu and then the mainboard. Stick with it. You'll find out which it is. Good Luck.

May 21, 2009 | ASUS P5S800-VM Motherboard

3 Answers

I hav a P-III on Intel810. The problem is it does not boot.


if it cannot even light the keyboard numlock led, the board is fried

May 14, 2009 | ASUS Intel 810 Chipset CUW-FX Motherboard

1 Answer

COMPAQ PRESARIO DESKTOP PC SR1215IL. When switched on, cpu boots normal but no display on monitor. instead a sharp and bright blue vertical line appears for few seconds on the middle of screen. led of the...


tricky!! oh hi im Dyanne.. a totally unresponsive black screen can be th result of failure of th LCD or LCD inverter.( a specialized piece of electronics that energize th screen) to rule out th failure of th video display adapter or circuitry, try plugging in an external monitor..a standard pc monitor.. attached direct to th lappy. if it works, (as i susopect) th motherboard and video display are both working ok and its th LCD which is at fault. this can sometimes be repaired by a competent specialist. good luck xx

Dec 25, 2008 | Compaq Evo D300 PC Desktop

1 Answer

No display at post


There are a few things that can cause no display on the monitor.
That single beep means POST = Power On Self Test. Post has tested everything on you're board to be good.
The cable between video card & monitor may be bad or not connected correctly (Swap out the cable as last resort).
2. You're monitor is defective, try swapping it with known working monitor.
3. You're video card is not functioning.
Lastly, when you reset the system cmos/bios everything went back to default. This means you're bios is now using the onboard PCI video graphics. Remove you're radeon 9600 video card. Try booting the system. You should see display again. The only way to test you're radeon would be to boot to the bios & set bios to boot using the AGP radeon. You need to change Init Display First to AGP & not PCI. If you loose video than you know you're AGP card is bad. Reset the cmos/bios before adding another AGP card or you will not get display. This setting is on pg 3-5. Integrated Peripherals. If you need you're manual you can download it from this link: http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=NF7-S2G&fMTYPE=Socket+A

Good Luck!
Mike

Jun 06, 2008 | Power Color RADEON 9600 (128 MB) Graphic...

10 Answers

My Intel D845EPI/D845GVSR MB processor does not boot up. No BIOS or POST is dispayed on the screen


Try to use working processor from your friend, If the problem still the same possible your motherboard has been damage. Ask for a warranty for the supplier.

Don't rate me Inappropriate if you don't like my solution or rate me SOLVED if this solution solved your problem. Thanks

Nov 23, 2007 | Intel D845EPI (INTELKD845EPILPAK10)...

13 Answers

Intel 845 GVSR


90% in d845gvsr cpu dry problem , when we press fan after that swicth on the system may be it's giving display solution is bake cpu socket at 200 digree C, after it's working fine otherwise there is no solution. cpu socket problem like hang, restart, some time display , just bake the cpu socket with hot air gun or bga machine,

Nov 11, 2007 | Intel Motherboard

1 Answer

Got power, but no booting activity


Assuming you have compatable memory fitted to the mobo; if you cannot get as far as the power on self test (P.O.S.T) or into the bios to set it up, remove all components you have fitted apart from the memory and the hard drive and a graphics card if not on board graphics and see if you can get as far as the post screen. If nothing appears and you just get a flashing cursor, then either the bios chip is faulty, or you have possibly stressed the board when fitting components and accidently broke a soldered contact. If you do get the post try putting back one peice of hardware at a time until you come across the problem part.

Jul 10, 2007 | Abit SG-80 Motherboard

Not finding what you are looking for?
Intel Motherboard Logo

670 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Alun Cox

Level 3 Expert

2679 Answers

Ekse

Level 3 Expert

13434 Answers

Joe Negus
Joe Negus

Level 2 Expert

652 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...