Question about Andis Styliner SLII Hair Trimmer

Open Question

Pulls when cutting - Andis Styliner SLII Hair Trimmer

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thread pulls out of needle after cutting. I have tried all the obvious usual solutions.


Before you cut, make sure to use the manual wheel to bring the needle down, as if it's about to make another stitch; stop the needle before it touches the fabric, pull the thread from the fabric a few inches, and then cut.

Nov 10, 2014 | Sewing Machines

1 Answer

96 chevy radio, wipers, cruise and climate controls not working


Check the fuse(s), it could have been tripped. Also could be a short (a common place is in the cigarette lighter). As for the steering wheel involvement, what do you mean by 'pull down'? Turn it, adjust it, just literally pull/push down on it?

Apr 02, 2013 | 1996 Chevrolet K1500

1 Answer

Is it better to cut on the pull stroke or the push stroke with a hack saw?


it is better to cut with the pull stroke, because the tension is increased on the blade while pulling. because you can attach the blade in whichever direction you like, i suggest you attach it so the teeth are facing in the way that will be best for cutting on the pull stroke

Jan 28, 2013 | Saws

2 Answers

Is it better to do pull cuts or push cuts with a hand saw?


it is a matter of debate, and ultimately up to your personal preference. i keep a steady pressure on the wood at all times, so the saw cuts during the push and the pull

Jan 28, 2013 | Saws

1 Answer

Changing fuel lines


pull the old line out on the new line cut it down to 1/3 about a 1/2'' long feed a wire down the hole and out the filler neck slide the new line over the stiff wire and slowly pull the wire out when the cut end pops threw pull out the wire then pull the line tight and then threw the opening install the fuel filter before pulling all the way in

Sep 30, 2012 | Poulan Pro 16-Inch 38 cc Anti-Vibration...

1 Answer

I was cutting 16" logs


The motor is locked up.What it did is seized the rod too the crank.Hate to say it but it,s time for a new saw.

Nov 29, 2010 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

My kawasaki zx7r 1997 cuts out when i turn the handle bars on full lock when idleing,been told it might be wiring worn by the ignition or it might be that i need to re-tune my carbs or jets. will either of...


try pulling on the wiring to the ignition switch and kill switch with the handle bars straight, if the engine cuts out then you have a broken or damaged wire in the loom, cut the wiring loom open and pull on the wires one at a time untill it cuts out, the wire you pull when it cuts out will be the one you need to repair/ replace

Jun 16, 2010 | 1997 kawasaki ZX-7R

1 Answer

I have an atco commadore B20 that cuts out when I


it could be tight cutter bearings in the deck next time it cuts out switch off the motor and try to turn the deck by hand if its realy tight its seizing up on you

May 02, 2010 | Garden

2 Answers

Renew pull start cord


Go to smalleng.com they have video on how to do what you need. Check it out awesome website!

Nov 24, 2009 | Husqvarna Partner Gas Powered Cut Off Saw...

Not finding what you are looking for?
Andis Styliner SLII Hair Trimmer Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Andis Health & Beauty Experts

Bruce Showalter

Level 2 Expert

133 Answers

shaveroutlet.com
shaveroutlet.com

Level 3 Expert

1639 Answers

Anthony Ward
Anthony Ward

Level 2 Expert

397 Answers

Are you an Andis Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...