Question about Singer Sewing Machines

1 Answer

I've lost my needle plate ,bobbincase cover and presser foot for my singer stylist 534 do you have them ?

Bobbincase cover, presser foot, needle plate

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Singer Master
  • 7,365 Answers

Http://www.sew4less.com/product/5952/Needle_Plate_310706_312081_312391

http://www.sewingpartsonline.com/Singer-534-sewing-machine-parts.aspx

I can't find a bobbin case cover,, I suggest that you go to these
2 sites & call them or email them about the bobbin case cover
sewvacdoctor.com
a1sewingmachines.com

Posted on Sep 30, 2012

Ad

5 Suggested Answers

SewTechWayne

SewTechWayne

  • 186 Answers

SOURCE: faulty presser foot lifter on a singer 2110/2112.

I have seen these machines with broken presser bar clamps (something inside the head). If it is just a bind then some oil on the presser bar may work, if the clamp is broken then it is probably not worth fixing.
Good luck!

Posted on Jan 31, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: singer stylist sewing machine 534 is not stitching

Feed dog drive gear(2) are plastic and are probably stripped. Always replace them in pairs. While you are at it replace both hook drive gears as well. It will run as good as new.

Posted on Mar 28, 2009

Anonymous

  • 1 Answer

SOURCE: The presser foot lifter of my Singer 9432 has disconnected

Had the same problem.
Open the cover where the light bulb is.

Follow the presser foot rod up into the machine.

You will find a metal keeper with a set screw facing the now open end of the machine.

That set screw has most likely come loose.

Since the presser foot is spring loaded to the down position leave the presser foot raising lever in the down position.

With your flat bladed screwdriver, gently push the metal keeper to it's lowest position. If it does not go easy, loosen the metal keeper set screw a bit. Lefty loosey.

Tighten the set screw on the metal keeper. Righty tighty.

Posted on Jan 03, 2010

ken dourof

  • 980 Answers

SOURCE: I have a Singer Stylist 543. The feed is not

If you have taken the needle plate off recently make sure you have put it one correctly, failing that you need to get underneath the teeth by taking the machine bottom off and you will see a large screw that you can adjust

Posted on Mar 09, 2010

hazelgrace

hazelgrace

  • 340 Answers

SOURCE: how t o thread a

Try this site, it has step by step instructions with pictures for threading a 534.
http://www.instructables.com/id/Threading-the-ITP-Singer-534-Stylist/

Posted on Aug 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Needle bar does not move in zig zag mode on singer 457 stylist and will not move to full left with the position lever


Have you changed your presser foot over to the zig zag foot? On some machines it won't work correctly until you change to the correct presser foot.

Aug 24, 2017 | Singer Sewing Machines

1 Answer

Feeddog singer stylist 776 how would the feeddog gt lowered


Consult the owner's manual. There should be instructions for how to darn with your machine. It would require either the feature that lowers/raises the feed dogs or a cover plate that attaches over the feed dogs.

If your machine came with the cover plate accessory, and the feed dogs are not rising to feed the fabric, then I suspect the machine has not been cleaned & oiled in quite some time and perhaps the feed dogs have seized. When you run the machine (remove the needle and presser foot), watch if the feed dogs actually drop below the needle plate, move toward the front of the machine, then rise above the needle plate and move toward the back of the machine. This is a repetitive motion that actually pulls the fabric through the machine. If this is not happening with your machine, it needs service.
...
Singer Stylist 776 Manual Page 8

Oct 30, 2016 | Singer Sewing Machines

1 Answer

Stylist 534 in cabnet


here is a link for part of what you need, you'll have to check with a sewing machine shop for the needles. Singer 534 Parts

Jul 14, 2014 | Singer Sewing Machines

1 Answer

Singer Stylist 11 Serger problems with right need skipping stitches how can I solve the problem


SKIPPED STITCHES ON A SERGER
1. Is the needle bent or worn--replace
2. Is the needle inserted correctly into the needle holder--check needle
3. Is the Serger threaded correctly--rethread
4. Is the presser foot pressure right for the fabric--adjust

Jan 04, 2013 | Sewing Machines

1 Answer

I have a 9960 singer machine and am trying to use the buttonhole presser foot for the first time and I can not get it to sew T


the buttonhole foot snaps on to the presser bar, there's a little lever at the back of the presser bar that releases the foot, then put the buttonhole foot down on the needle plate & use the presser foot lifter (number 11) to lower the presser bar down onto the buttonhole foot & you'll hear a click sound when it snaps on & make sure to use the buttonhole lever(number 31) because the machine won't sew a buttonhole unless that lever is pulled down.

Apr 26, 2012 | Singer Sewing Machines

1 Answer

My new Singer Stylist 7258 keeps getting a message code C4 and I can't find anything wrong with it. Please advise.


I looked in my manual, it says that C4 means that the thread is tangled or there bobbin was interrupted forcibly. Turn off and totally rethread your machine with presser foot up, insert a new needle and try again. Do this test, with the presser foot up, pull top thread, it should move easily, now lower presser foot, pull thread, it should barely move. This should seat the thread in the tension discs properly. I have this same machine, and love it.

Mar 11, 2011 | Singer Sewing Machines

1 Answer

My 534 machine jammed and bent a needle. I removed the bobbin case and put it back in but now when i have rethreaded(with a new needle) and inserted the bobbin, the top thread is not moving under the plate...


Try pulling on your top thread with the presser foot up, it should pull smoothly, now put the presser foot down and pull the thread it should barely move. Another thing to try is change your stitch pattern, straight to zig zag and back, it may reset. Other than that, without seeing it, it is hard to say.

Nov 01, 2010 | Singer 3116 Simple

1 Answer

How t o thread a singer stylist 534


Try this site, it has step by step instructions with pictures for threading a 534.
http://www.instructables.com/id/Threading-the-ITP-Singer-534-Stylist/

Aug 28, 2010 | Sewing Machines

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Singer Sewing Machines Experts

Cindy Wells

Level 3 Expert

6074 Answers

Kelley Buchanan
Kelley Buchanan

Level 2 Expert

130 Answers

tsalagi152

Level 2 Expert

89 Answers

Are you a Singer Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...