Question about Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Open Question

Fisher Paykel f1

Have f1 , on the top drawer, no power to bottpm drawer, I replaced the flood switch, problem persists. no water in the bottom tub, so drying it out isn't needed as it is quite dry. We had a power outage and ever since it came back on we have had this problem. Somebody please point me in the right direction.

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Master_Tech

Gary Davd

  • 770 Answers

SOURCE: Fisher Paykel No power to bottow drawer

the board you checked has the sensor have you removed and dried off both of them? and check the actuator motors that hold the lid down these fail causing the F! due to the lid not sealing tight'

Posted on May 20, 2008

Ad

Anonymous

  • 572 Answers

SOURCE: Fisher & Paykel 2 drawer dishwasher: I too

he might have unplugged something in the proccess of drying the bottom

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher paykel dd605


F1 (or E1) is a "Flood" fault and means there is water in the bottom pan. This is beneath the bottom drawer. The sensor is in the left, rear corner of the base pan. Any kind of leak, including over sudsing or split hoses or or lid not down fully due to tall items in tub, can cause this. Remove the lower drawer, dry the water from the pan bottom, reinstall the lower drawer and check operation. If this error recurs you must find the leak and correct it.

Sep 26, 2016 | Fisher and Paykel Dishwashers

1 Answer

How do I stop the F1 error even after assessing there is no water in the bottom tray and dried it with hair dryer just in case


There should be F1 on both displays. "If power fails to the bottom tub it will cause the top tub to go F1. Test heater plate." (from the service manual).
If there is F1 on both displays it could be a faulty flood switch or PCB.

Jan 30, 2015 | Fisher and Paykel Dishwashers

1 Answer

Flood switch 920 model


Not sure what the actual model number is but usually the F1 error with Fisher and Paykel dishwasher means water has entered the flood switch located at the base. This could be due to leaky hoses or water leaking through the door or lid seal. Wait for a day or two until the water evaporates and try again. Otherwise you will have to dry out the flood switch and then try again. Location of flood switch will depend on your model. For double drawer dishwasher you will have to take the bottom drawer out from the housing and the switch is on the floor of housing. But make sure you take the mains power chord out before touching the insides of dishwasher. Will also need to find the cause of the leak. Other reason for F1 could be loss of power to top dishdrawer if you have double drawer. But in that case the top drawer will have no lights on. The power board is located on the base of housing under bottom drawer. Once again do not touch inside of dishwasher without shutting off mains power.

Jan 27, 2014 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Fisher & paykel fault "F1" is displayed on the top


hello
F1 means the flood sensor senses water at base of machine at PC board.
You need to take out bottom drawer and check for water puddle under where the drawer was.If there is water you can get the machine going again by comletely drying it out(F1WILL CLEAR),but it still means you have a leak.With bottom drawer out you can really see whats going on.Once F1 is clear you can actually run upper drawer and see if it leaks.Most likely culprit are the lid actuators.Replace all 4 . It'll run like new.Don't overload drawer .That can cause lid leak too.Also the PC board may be damaged and may start to go crazy giving fake F1 codes.$80 easy fix.
good luck

Jul 27, 2011 | Fisher and Paykel 23 in. DD603H SS...

2 Answers

We have a 23" Fisher&Paykel dishwasher and got


The F1 error coming on top drawer when operating bottom drawer is due to the thermal fuse blowing up on the bottom drawer and shutting controller power.

The thermal fuse could have blown either as a normal component failure or heater over heated due to thermostat failure. In any case this can be repaired by replacing the whole heater assembly as all the parts are integrated.

This is at the underside of the drawer and will need a technician to replace unless you are very familiar with repairing electronic dishwashers. The part look like this.

The way you have described the onset of the F1 error is not due to flood switch. You can confirm that the lights on the bottom drawer are out even though the top drawer is showing F1 and beeping.

If problem was flood switch then both drawers would show F1.

Nov 25, 2010 | Fisher and Paykel 23 in. DD-603 Built-in...

1 Answer

The flood switch has been activated on our Fisher & Paykel 2-drawer dishwasher. How do we reset the button?


Turn off the main power to the dishwasher.

I am assuming you are getting F1 error code flashing (if your drawers have LCD display) or the LEDs are flashing if you have intergrated drawers.

The flood switch is located at the base of the drawer tub. You will have to either extend the drawers out fully or take them out depending on the amount of water that would have collected at the base of the tubs. Get some towels and dry the base out. You may also need a hair dryer.

Once the flood switch dries off the drawer should work ok when you turn back the power.

The causes of the flood switch trriggering is either too much foam in detergent (use recommended detergent) or leak in water in or drain pipe.

Please remember to rate the solution if it helps or post a comment if not.

Jun 12, 2010 | Fisher and Paykel Dishwashers

1 Answer

F1 bottom drawer locked


F1 means the flood switch has been activated. here is a trouble shooting flow chart.
1. did a flood occure? yes. q-2 or no q-12
2. is the lid sealing on the tub correctly? yes Q-3 no=Answer
3. Is there a high water level in the tub. Yes-q4 no q-6
4. is the water valve leaking? yes=Answer no-Q 5
5. Is the dish drawer priming correctly? yes q-11 no q-6
6. Is the spray arm split. yes=answer, no q-7
7. is the spray arm running freely. yes q-8 no q=answer
8. is the water leaking from a split inlet or drain hose? yes = answer, no q9
9. is the water leaking around the heater plate or o rings. yes=answer, no q10
10. carroy out more testing to locate the source of the leak.
11. drain hose may have been blocked or partially blocked.
12. is there water or condensation around the chassis flood switch pcb.
13. if power fails to the bottom tub, it will cause the top tub to f1

Jan 07, 2010 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

My Fisher Paykel dishwasher is flashing F1 - top drawer only. The bottom drawer is working just fine.


F1 error means the flood switch in the drawer is activated. If there is water inside when you open the drawer then you will have to manually empty it with a small container.

Most likely the solenoid that controls inlet water is faulty or the water level sensor is faulty.

Try turning the mains power and water off and on again and run dishwasher. If fault persists then you may have replace the parts.

Nov 11, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

Hi Both drawers show error F1 flashing beeping with rinse light on and both pumps run after power is applied to machine


F1 error indicates flood switch in base has activated, meaning machine has leaked. This causes machine to drain continously, and can only be stopped by switching off power. Not easy to fix if you don't have experience- bottom drawer has to be removed to access flood switch, then machine needs to be test run and checked for leaks. Best to call the professionals!!

Oct 03, 2009 | Fisher and Paykel 23 in. DD603H SS...

Not finding what you are looking for?
Fisher and Paykel 24 in. DD603H W Built-in Dishwasher Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Mark Davis

Level 1 Expert

18 Answers

Bruce Denton

Level 2 Expert

273 Answers

Paul Bade

Level 3 Expert

1662 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...