Question about Cuisinart BFP-703 SmartPower Duet Food Processor

1 Answer

Cuisinart smartpower duet BFP703 food processor repair manual

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Oh some of these answers... the most common issue with blender is that the removable blade unit starts to jam. So :
1. unscrew it, clean it and make sure it turns easy
2. open the unit and replace the fuse that blew up because turning the blade became too hard.
Voila

Posted on Aug 21, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 38 Answers

SOURCE: Blender Dead as a Doornail

open unit wil find thermal fuse replace.alternative the lid that covers bowl normally turns cliickinto position .this activates aswitch check if properly locked in

Posted on Mar 21, 2007

ThaMp3Doctor

ThaMp3Doctor

  • 8597 Answers

SOURCE: How to put new shaft on cuisinart food processor model DLC-7E

Initial disclaimer: I am not recommending this course of action - my recommendation is to buy a new food processor. These units weren't designed for DIY repair, so this is going to be a difficult task. The final product probably isn't even going to be pretty. You are well out-of-warranty, or I wouldn't even consider posting this. First, make sure you have a DLC-7E shaft - the only way to get one at this point would be to buy a DLC-7E base from eBay or an after-market seller, as all of these were manufactured well over 20 years ago. I don't currently see any eBay listings for one, but they do crop up from time-to-time. Make sure the DLC-7E you are repairing and the old one from which you are wrenching the old shaft are unplugged and have been unplugged for an hour or longer just to be on the safe side. Unscrew the four screws on the bottom of the base on both units. If the bottom base does not come off after this, carefully pry out the four feet and unscrew any hidden screws that might be hidden underneath the feet (Careful - original feet cannot be ordered by normal means, and damage will only add to your total repair cost). Take note of the guts on the inside of both food processor bases - if you have to unscrew the motor body (4 screws that sit just underneath the top of the base), take note of everything that you are taking out so that you can put it back in its proper place when done. Wear leather gloves for safety. Please be aware that even an unplugged unit still has the potential to send several volts of electricity through your body - this is a potentially hazardous task. Once the motor body has been unscrewed and removed slightly (don't disconnect any wires or cables - just get the motor body out of your way), you will notice the old shaft that you intend on replacing. Look for any damage to the gears/bearing that surround this shaft. Try dabbing a small amount of USP-grade mineral oil on any bearings - clear away any dust or debris that may be obstructing the shaft from turning. Don't overapply the oil, or the wetness will seep into other electronic components in the motor and cause them to fail. Put your food processor back together, turn it on, and press the button/buttons on top of the base of the food processor with a pen with the food processor plugged in. If the shaft still won't turn, you definitely need to replace the old shaft (you can disregard some of these previous steps if your problem is that the spindle on the old shaft is worn).
Remove the screws and disassemble the processor base as described above. Since there is a layer of paint/coating surrounding the old motor shaft, removing the old shaft may cause paint flecking. Take the shaft from the one food processor base and insert it in the food processor you are trying to repair. Strip away any excess paint/coating from the new shaft. Make sure no paint flakes remain in the body of the food processor, or they will later cause more serious problems that will permanently damage your food processor - potential fire hazard as well. You will probably notice that the new shaft does not look as pretty as your original shaft, since the paint/coating will almost invariably get damaged in this process. Reassemble the base of the food processor, making sure no wires, etc. were knocked out of place in the process. This paint flecking will add to the cost of the repair - you may need to buy appliance body paint that dries to almost a rubbery consistency to make the final project look nice. All of the materials listed above could cost you $40 or more.

Like I said, I don't reccomend this course of action, but there's your answer.

Posted on Mar 17, 2009

ThaMp3Doctor

ThaMp3Doctor

  • 8597 Answers

SOURCE: instructions for the food processor of my Cuisinart Duet

Place the gearbox on top of the blender/food processor
Place the work bowl over the spindle, with the handle facing the front of the machine - make sure the tabs lock into place.
Place the stem adapter on top of the spindle, then the blade.
Place the lid on top of the bowl, with the feed tube facing the back of the food processor. Then the pusher into the feed tube.
Here is the link to the user manual with visuals 9p.6 is most helpful):
http://www.cuisinart.com/share/man/10_man.pdf

-Tha Mp3 Doctor

Posted on Mar 23, 2009

R.Kavitha

  • 122 Answers

SOURCE: Need instruction manual for Cuisinart DLC-7 food

pl. see www.manualnguide.com/brand/cuisinart/

Posted on Apr 16, 2009

Anonymous

  • 2 Answers

SOURCE: need manual for food processor

Found it at:

http://safemanuals.com/user-guide-instructions-owner-manual/CUISINART/DLC-10S-_E

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lights come on, motor turns briefly, then stops


Check that blade can turn easily with unit unplugged. Fix that first then replace the fuse.

Dec 15, 2012 | Cuisinart BFP-703 SmartPower Duet Food...

1 Answer

Takes too long. Base heats up.


attach a fan to the base with some sticky tape. it sounds like it's getting too hot causing a catastrophic failure of the internal ailerons and thingy mebobs.

Apr 25, 2009 | Cuisinart BFP-703 SmartPower Duet Food...

1 Answer

My mini cuisinart stopped working


Place the gearbox on top of the blender/food processor
Place the work bowl over the spindle, with the handle facing the front of the machine - make sure the tabs lock into place.
Place the stem adapter on top of the spindle, then the blade.
Place the lid on top of the bowl, with the feed tube facing the back of the food processor. Then the pusher into the feed tube.
Here is the link to the user manual with visuals (p.6 is most helpful):
http://www.cuisinart.com/share/man/10_man.pdf

Mar 23, 2009 | Cuisinart BFP-703 SmartPower Duet Food...

1 Answer

Instructions for the food processor of my Cuisinart Duet


Place the gearbox on top of the blender/food processor
Place the work bowl over the spindle, with the handle facing the front of the machine - make sure the tabs lock into place.
Place the stem adapter on top of the spindle, then the blade.
Place the lid on top of the bowl, with the feed tube facing the back of the food processor. Then the pusher into the feed tube.
Here is the link to the user manual with visuals 9p.6 is most helpful):
http://www.cuisinart.com/share/man/10_man.pdf

-Tha Mp3 Doctor

Mar 23, 2009 | Cuisinart BFP-703 SmartPower Duet Food...

1 Answer

INSTRUCTION MANUAL NEEDED


The FPB-5SA is the Sam's Club version of the BFP-703. Here is a link to the manual:
http://www.cuisinart.com/share/man/10_man.pdf

-Tha Mp3 Doctor

Mar 19, 2009 | Cuisinart Food Processors

1 Answer

The Blender attachment will not turn, just grinds and smokes.


The motor shaft that spins the teeth that are on the base of the blender may be frozen up for some reason. If you purchased the duet within the last 3 years and have a receipt, call Cuisinart to get it repaired in warranty - even if you don't have a receipt, your serial number may still save you. If you purchased it more than 3 years ago, let me know.

Mar 12, 2009 | Cuisinart BFP-703 SmartPower Duet Food...

1 Answer

Blender Dead as a Doornail


open unit wil find thermal fuse replace.alternative the lid that covers bowl normally turns cliickinto position .this activates aswitch check if properly locked in

Mar 21, 2007 | Cuisinart BFP-703 SmartPower Duet Food...

Not finding what you are looking for?
Cuisinart BFP-703 SmartPower Duet Food Processor Logo

663 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cuisinart Food Processors Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Cuisinart Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...