Question about LG LFX25976ST - 3-Door French Door Refrigerator with Ice and Water Dis

2 Answers

Ice maker The cube tray in ice maker is in upside down--dump position & won't flip back over--the water tries to come in & runs down front of refrigerator. I checked for ice blockage--but doesn't seem like there is none-- I shut the ice maker off because I was afraid water running down might damage the electronic panel.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,370 Answers

Before going to buy any parts directly.
Go through this troubleshooting help links.

-------------------------

This is list of refrigerator problems, which is normally faced in refrigerator.
You can go through the details, by clicking the link below:---

--------------
Refrigerator is not cooling properly?
http://technoanswers.blogspot.com/2011/06/refrigerator-is-not-cooling-properly.html
-----------
Both refrigerator and freezer not cooling properly in refrigerator?
http://technoanswers.blogspot.com/2011/06/both-refrigerator-and-freezer-not.html
----------
The ice maker not working: ---
http://technoanswers.blogspot.com/2011/06/ice-maker-stopped-working.html

------------
Compressor not running on refrigerator?
http://technoanswers.blogspot.com/2011/10/compressor-not-running-on-refrigerator.html
--------
Water dispenser not working on refrigerator?
http://technoanswers.blogspot.com/2011/10/water-dispenser-not-working-on_19.html

-------------

Ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-making-ice.html

-------------

Water Overflows in Ice maker and freezes inside?

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-overflows-in-ice-maker-and.html

-------------

How to replace Ice maker assembly?

http://alltypesofpartsreplacing.blogspot.com/2011/10/how-to-replace-ice-maker-assembly.html

other ice maker related issues and solutions:---


===========


Ice maker dispensing ice with black or white plastic pieces in ice?


http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-dispensing-ice-with-black-or.html


After replacing ice maker assembly, ice is not getting made?

http://alltypesofpartsreplacing.blogspot.com/2011/10/after-replacing-ice-maker-assembly-ice.html


Ice maker is leaking water and causing the ice to freeze?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-is-leaking-water-and-causing.html


Ice maker is noisy and not making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-is-noisy-and-not-making-ice.html


Refrigerator ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/refrigerator-ice-maker-stopped-making.html


Ice maker leaks water into ice bin causing a glob of ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-leaks-water-into-ice-bin.html


Amana Refrigerator leaking water from ice maker?

http://alltypesofpartsreplacing.blogspot.com/2011/10/amana-refrigerator-leaking-water-from.html


Ice maker leaking?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-leaking.html


Ice maker is dumping the ice cubes out before frozen solid.

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-is-dumping-ice-cubes-out.html

Water overflowing ice maker?

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-overflowing-ice-maker.html


Ice cube is getting stuck up hard in ice maker

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-cube-is-getting-stuck-up-hard-in.html


Icemaker quit working?

http://alltypesofpartsreplacing.blogspot.com/2011/10/icemaker-quit-working.html


Quit making ice

http://alltypesofpartsreplacing.blogspot.com/2011/10/quit-making-ice.html


Water leaking into ice tray, frozen glob of ice

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-leaking-into-ice-tray-frozen-glob.html


Not making ice, and water leaking in freezer?

http://alltypesofpartsreplacing.blogspot.com/2011/10/not-making-ice-and-water-leaking-in.html


The ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-making-ice_20.html


Ice maker not making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-not-making-ice.html


Ice maker quit working?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-quit-working.html


Ice maker dispensing black pieces of plastic in the ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-dispensing-black-pieces-of.html


Replaced Ice maker but its still not making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/replaced-ice-maker-but-its-still-not.html


Ice maker leaked creating an ice block?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-leaked-creating-ice-block.html


Ice tray leaked?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-tray-leaked.html


Ice maker stopped functioning?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-functioning.html


Ice maker stop working?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stop-working.html


Ice maker failed

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-failed.html


Old ice maker stopped working?

http://alltypesofpartsreplacing.blogspot.com/2011/10/old-ice-maker-stopped-working.html


Old ice maker started leaking?

http://alltypesofpartsreplacing.blogspot.com/2011/10/old-ice-maker-started-leaking.html


Ice maker not working?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-not-working.html


Ice maker overfills and cause water to flow into ice dispenser and freezes?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-overfills-and-cause-water-to.html


Ice maker didn't make ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-didnt-make-ice.html

Ice maker was leaking?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-was-leaking.html


Ice maker was leaking after it filled up with water?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-was-leaking-after-it-filled.html

These will help.

Thanks,.

Posted on Dec 22, 2012

Ad

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I installed the water line for my ice maker today,When i turned on the water i can see the water over flowing the ice trays and wont stop coming out unless i shut the water off.Please help.Thanks Bill.

Posted on Jun 04, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

  • 1 Answer

SOURCE: LG SXS Refrigerator LSC26905 ice maker

I was able to order the ice tray myself and install it in the fridge - it's not hard. I ordered from one of the parts sellers linked to at the LG website, not those listed in other posts here.

Here's how to replace the tray:

You need to remove the tray dumping mechanism to do this.

  1. Remove the ice bin, set it aside (don't forget to deal with the ice melt).
  2. Turn the ice maker off (LG says to unplug the fridge, I didn't).
  3. On the left hand side of the ice tray dumping mechanism there is a screw helping to keep the entire thing suspended from the ceiling of the freezer. Remove that screw- don't worry, the mechanism will stay put for now.
  4. The dumping mechanism can now slide forward- note that you can't completely remove it from the freezer yet, but slide it forward and it will no longer be suspended from the ceiling. Don't let it drop or hang.
  5. You need to disconnect its power supply now. On the left hand side you should see a small bundle of wires coming from the back of the freezer to the dumping mechanism. It connects to the dumping mechanism's set of wires with a pair of white plugs. Pull these plugs apart. You may need to pry the catch on these plugs apart while you pull.
  6. Now you can take the dumping mechanism out of the freezer (and close your freezer).
  7. To remove the ice tray you need to slide the housing that contains the rotating motor out of the housing. This is on the right side of the mechanism. If you have trouble identifying it look at the underside of the entire thing and you'll see a small "test" button. That button is on the motor.
  8. To remove the motor you'll see two catches on the right side- you'll need to pull these catches out without breaking anything. You'll be able to slide the motor down and out when you get it right.
  9. Sliding the motor out lets you get the old ice tray out now. There is probably a set of white wires routed through a little catch on the old ice tray that you'll need to free.
  10. Put the new ice tray back on the motor. You'll need to get the left side secured at the same time you get the motor housing in its catches of the dumping mechanism.
  11. Reroute those white wires back on the new ice tray.
  12. Reconnect the electric wires to the housing.
  13. Slide the entire dumping housing back onto the ceiling of the freezer and screw in on the left side.
That's it. You can press that test button on the underside of the motor. This will dump the tray and immediately refill it with water so you can observe if everything is working.

Posted on Aug 28, 2009

Anonymous

  • 706 Answers

SOURCE: Ice Cube Maker

Here is a link for the srevice manual ( section 7 discusses how to troubleshoot an ice maker ) that should get you going..

http://136.166.4.200/contents/Fridge/LFX25960/LFX25960_Service_Manual.pdf

Hope this helps you...

Posted on Sep 15, 2008

BIKER T

Terence Fourie

  • 909 Answers

SOURCE: Ice maker wont shut off

So many different types. lots of info needed. In short, lg have DIPswitches on main board. By adjustment of these switches, the water in can be controlled.I dont think there is a water sensor on these makers per say.Does the water ever switch off at any time and if so, is the inflow time constant?. Assuming the solonoid valve is not defective.

Posted on Jan 30, 2009

Anonymous

  • 1 Answer

SOURCE: Ice Maker Freezing Up and Ice not dispensing

Check your ice cube tray to see if it is warped. Mine was. I took the tray off and dipped it into boiling water and remoulded it to the original shape and re-installed it. So far no problems. The tray gets warped because of the ice cube release mechanism. The tray is rotated around until it meets a block on one corner which creates the twisting motion we used to do on manual trays. Over time it tends to warp the tray. Good luck

Posted on Apr 28, 2009

christian nielsen

  • 358 Answers

SOURCE: Ice Maker Problem with overflowing

When the ice maker calls for water it pours for about 7 seconds if more will overflow and the problem is in the ice maker board but if pours water for nomore than 7 seconds and still overflow it means that was extra water in the ice maker ,that means that the dual water valve(located in the bottom back of the refrigerator) is leaking and needs to be replaced.

Posted on May 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ice maker inst working Whirlpoo; model gz25fsrxyy2


By "ice maker isn't working" do you mean it isn't filling with water, it isn't freezing the water in the ice maker, it isn't dumping the ice cubes into the bin, or it isn't dispensing ice cubes?
Was it previously working and it is not working now?

Typically one can hear the valve when it opens to fill the ice maker with water. Can you hear it attempting to do so? If so, and there isn't any water in the ice tray, check that there is water supplied to the valve at the wall and the valve is open. Is there a water filter? Has it been replaced per the manufacturer's recommendation? (Typically, the water filter should be replaced every six months.)

Is the "full" bar pushed up? It shouldn't be. The bar above the ice cubes should not be in the horizontal position. That position tells the ice maker the bin is full so it should wait until the bar goes down, indicating some ice has been used.

Can you hear the bayonet turning? Is the ice maker attempting to dump out cubes whether or not they exist? The next issue after you confirm there is water going into the ice maker that is being frozen and the ice maker knows to dump the ice, is the bayonet. There is a motor that turns the bayonet and a mechanical connection. Either could be at fault.

3a674049-367e-41d5-9898-076fa5c37ced.gif

Jan 22, 2018 | Refrigerators

1 Answer

My ice maker does not make ice but water does run to front of fridge plz Help ????


I can't make out the words in your picture so there is not a lot of information to go on, but I will give it a try. If yours is like my refridgerator, there are a couple of off switches for the ice maker. One is on the control panel like the one you tried to photograph. Mine selects crushed ice, cubed ice, or ice off. The other soff switch is the lever switch that sits over the ice cube reservoir inside the freezer and shuts off the ice maker when the reservoir is full. If this lever switch is stuck in the up position you will make no ice. You say that water runs out of the front. Another problem that I once had with my ice maker was that the plastic housing around the ice cube tray cracked. One tray of ice cubes was made but when the ice maker flipped the tray over to expel the ice cubes the cracked plastic prevented any torque on the tray and the ice cubes would not come out. When the tray returned to the upright position new water would flow onto the tray, but since it was already full of ice cubes the water would simply overflow into the ice bucket reservoir. It did this over and over until I had an ice sculpture in my freezer and reservoir instead of ice cubes.

Jan 02, 2017 | Refrigerators

1 Answer

Kenmore 795.5102 will not make ice


The problem is the ice maker, the modular head of the ice maker has broken, hence the clicking sound and the raised arm stuck up. You will need to have an accurate model number and contact a local parts distributor for a new ice maker. It is a simple repair usually only 2-3 screws.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Apr 25, 2012 | Kenmore Side by Side Refrigerator

2 Answers

I have the samsung rs2577sl. the ice maker cube


Your model has the twist tray style icemaker. The part number for you front section that contains the motor assembly is DA97-00258E Ice Maker Assembly. You can try by taking it out and seeing if the tray will return to the home position but stopping there make me question if the thermal fuse in wiring harness may have blown. We may need to test that wire also to see if the thermal fuse is still good, I will leave you some of the links and ready to help when you need me, Thanks, Sea Breeze

Apr 21, 2010 | Samsung 26.1 Cu. Ft. Side-by-Side...

5 Answers

KitchenAid ice dispenser tray is dry - not working


Put some water in the ice mold is what I would try. wait and see if the ice maker harvest a batch. If it does drop a batch but no more then the water valve is probably shot. The ice maker itself controls the water. It does this by filling the ice mold for 7.5 seconds. Here is your Ice maker repair manual and some repair photos along with a pictorial which snows how to check the water valve.
Ice maker quit making ice

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Apr 05, 2010 | KitchenAid KSRS25IL Side by Side...

2 Answers

Jen aire ice maker not working


change filter and defrost water lines if frozen

Dec 10, 2007 | Jenn-Air Freezer Jenn Air Clear Cube Ice...

11 Answers

Samsung Icemaker Problem


I also had the ice tray stuck in the dump position. I unplugged it waited 5 minutes and pluged it back in. And the Ice tray moved back into the correct fill position, and the arm did drop down, But now it has not filled with any water. So now what should I try?

Feb 20, 2007 | Samsung RS2534 Side by Side Refrigerator

4 Answers

Ice cube dispenser not working


I had this problem. The root cause was that mineral deposits had built up in the ice cube tray. The ice would not "dump"... but stayed in the tray after the dump cycle. I did not catch it quickly and eventually the plastic frame broke. That was easily replaced. Inspect the ice tray to see that all cube surfaces are smooth. If there are mineral deposits, they need to be removed. Do NOT scrub with anything abraisive or you will ruin the tray. As you are looking straight on at the Ice maker, with the bin out, depress the small black retangular tab. The tray assembly will come apart to remove the tray. Rinse the tray, then fill with warm vinegar. Let it soak. You may scrub with soft cloth, finger or fingernail to remove deposits. Replace the tray and you should be in business.

Jan 02, 2007 | Samsung RS2578BB Side by Side Refrigerator

Not finding what you are looking for?
LG LFX25976ST - 3-Door French Door Refrigerator with Ice and Water Dis Logo

3,872 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

deecee73

Level 1 Expert

8 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a LG Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...