Question about Krups Small Appliances Espresso Machine
Have got machine out to use over Xmas. Changed water filter, de-calced machine twice and still problems. When turned on to make coffee, the water runs out of machine, beans get ground, produces coffee grind disc, but machine not making coffee. It's like the water isn't getting to coffee, so all we're getting in water streaming everywhere. Please help?
Hose get clog. And lines get dirty fast on this machine. Cracked hose. Check filter in between
Posted on Sep 04, 2017
The hose connected to the heating element has unattached or is leaking.
Posted on Sep 03, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
that mean no coffee go through us if you dont use the machine often you might have coffee residue on the grinder teet remove the coffee bean in the hole were the coffee bean goes use a brush and clean the grinder teet very good with the residue of coffee gonna grind and gonna go through thanks for usig fixya pierre
Posted on Feb 08, 2008
SOURCE: Krups XP7240 leaks
The grind selector knob can be removed with the following steps: 1) Remove screw on side near grinder (do not let the screw fall into grinder, :-) ), 2) use sharp knife or similar to pry off cover with three dots. This should be easy. 3) Now you can rotate the grind selector and see that the white clear plastic does not rotate and the black does. There are two little pieces (one black, one clear plastic) on opposite side from grinder that slide over eavh other to keep this knob 'locked' into place. 4) again with a sharp pointed knife or similar you can separate these two pieces to 'unlock' them. This is made easier by lifting the side of the bean holder by the grinder gently and tipping it up. Be careful not to force anything too much. The black part should pop off. 5) Now you can lift off the clear bean holder.
After this good luck. We made it farther into the machine, but could never get to where we needed to go to fix our problem.
Krups must be congratulated for designing a machine that cannot be repaired and must be replaced with new purchases.
Posted on Jan 11, 2009
After I changed piston sealing I get the same error 09. It was caused by missing connection to the thermoblock temperature sensor. In my case both connectors for thermocouple were cracked. They are located directly on the body of thermoblock, below two fuses, covered by rubber housing. After I solder them again on the position error 09 disappeared. Unfortunately it is necessary to open at least front panel of the machine. Moreover I tink that there is also important to save polarity of those two cables.
Posted on Aug 07, 2009
SOURCE: I have a 12 month
You need to open the machine which is easy see my other post on leaking krups xp7240. The grinder can be taken out by removing two torix screws. Probably the electical brushes are gone. Take the grinder engine to a repair shop where they replace them.
Posted on Aug 14, 2010
Tips for a great answer:
Feb 11, 2011 | Krups XP7245
May 31, 2010 | Krups Small Appliances Espresso Machine
May 10, 2010 | Krups Small Appliances Espresso Machine
Oct 10, 2009 | Krups FME4 Coffee Maker
Sep 11, 2009 | Krups Small Appliances Espresso Machine
Jun 06, 2009 | Krups XP4030 Espresso Machine
Mar 09, 2009 | Krups XP7225 Espresso Machine
Jan 06, 2009 | Krups XP7230 Compact Super Automatic...
Jul 10, 2008 | Krups XP4030 Espresso Machine
May 19, 2008 | Krups XP2070 10 cup Coffee Maker/15 bar...
Jun 26, 2014 | Krups Small Appliances Espresso Machine
223 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: