Question about Irons

Open Question

My laurastar iron wont stop beeping

THE IRON WONT STOP BEEPING AND IS NOT STEAMING WHILE BEEPING

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 59 Answers

SOURCE: Brown spots coming from steam iron

you can mix 50% water with 50% vinager let it set in the iron overnight then turn it on and let the steam run out.What happens is the inside of the iron where the water is had corroded or rusted or has lime deposits.the vinager will break this loose overnight.also after you let the iron steam out all the mixture,flush the iron 4 to 5 times and start using fresh water from a store bought gallon.your tap water is probably full of iron.

Posted on Nov 15, 2007

Ad

Anonymous

SOURCE: Problem with Philips Azur Precise 4340 Iron

i had the same problem and the Philips hekp site was no use. I turned my iron off until it was completely cooled down then switched it back on again, with the steam number turned to 5 and the heat on max. as soon as the ready light went off, i put my iron in the horizontal position and shook it back and forth (quite vigorously) and it seemed to have dont the trick!

Posted on Aug 28, 2008

Anonymous

  • 1 Answer

SOURCE: Rowenta iron DX1700 not heating

I hate to say this but I came here looking for solutions and it seems the solution is not to buy this Rowenta overpriced products.

Posted on Dec 30, 2008

Anonymous

  • 2 Answers

SOURCE: beeping and error message

Your Iron has a faulty circuit board and need to be replaced

Posted on Jul 24, 2009

miket756

Michael Thorpe

  • 2702 Answers

SOURCE: shark iron wont turn on

take it back to were you got it from i think the regulator has just packed up

Posted on Jun 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steam iron not steaming was working ok one min then no steam


If the temperature dial is not set high enough, or the thermostat is faulty and setting the cut-off temperature too low, some steam irons will fill up their steam chamber in their soleplates completely with water and stop steaming, until the temperature returns above what's needed to continously generate steam.

Nov 26, 2017 | Irons

1 Answer

Why did my iron stop steaming suddenly


You have asked 3 times, please ask once and wait.

Sep 18, 2017 | Irons

1 Answer

Rowenta Pro Precision won't stop steaming until the tank runs dry.


Rowenta irons have a propensity for leaking. Most users do not add water to the tank but instead use a spritz bottle to dampen the fabric and then use the dry iron.

Jul 16, 2017 | Rowenta Irons

1 Answer

Hi Ihave a Bosch B25L steam generator iron and it has stopped steaming completely. Any ideas?


Yousaf/Tony, Either the switch is defective or the heat element has gone bad, probably not cost effective to repair.

May 25, 2014 | Bosch sensixx TDA 8333 Iron

2 Answers

"My rowenta DG9540 iron won't stop steaming. It starts as soon as it is switched on regardless whether the steam button is pushed in or not. What might the problem be?"


1) check the ejection button of the stems for particles, has blockage the mecanism by using hard water to due mineral deposit clean it.
2) other wise you must go to some repair shop for fix it.
God bless you

Jul 11, 2012 | Irons

1 Answer

While steaming clothing, a white flaky residue is being left on the clothing. Sole plate is clean. Residue seems to be coming from steam vents. What do I do to continue using this great iron? Evelyn Roll


Are you in a hard water or soft water area, maybe you could try using filtered water in your iron. To clear out the scale from the jets try adding a little white vinegar to the water and steaming it through, or a little "Calgon" diluted in water. Then perform a test iron on some dark fabric untill the scale has been removed.

Aug 02, 2010 | Rowenta DX6700 Iron

2 Answers

Hand steamer conair GS15R will not produce steam. It is on, it is full of water, the body gets warm, and it makes noises like it is steaming but nothing comes out.


Hi.

The iron steam lines may be clogged with limescale.

Try first using descaling solution to clean the lines.
Do descaling several times.

If that does not work, then the thermostat may have started malfunctioning and cutting off earlier than normal. This will cause water not getting enough temperature, and iron not steaming.

Try using a descaler product, often that can fix the problem.

Jan 14, 2010 | Conair Irons

1 Answer

Dirty water keeps coming out wen steaming , how do i clean it and stop this


Empty, then fill with vinegar, hold above a towel and let it steam till empty

Repeat with distilled water.

Nov 04, 2009 | Tefal UltraGlide Easycord FV4256 Iron

1 Answer

Iron not steaming


clean with 50/50 white vinegar water let soak overnight then flush out!!!! :)

Jul 06, 2009 | Rowenta Steam Generator DG050 Iron

Not finding what you are looking for?
Irons Logo

Related Topics:

451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Irons Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Brad Brown

Level 3 Expert

18157 Answers

Are you an Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...