Question about Windsor VS14 Versamatic Bagged Upright Vacuum

2 Answers

On a versamatic windsor how full can the bag get before you change it?

Posted by on

  • Anonymous Mar 21, 2014

    It will not turn on

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 1 Answer

Versamatic bags fill from the top, not from the bottom, so the suction doesn't diminish as the bag fills. It's a lot more efficient because new dirt doesn't have to forced thru what's in the bottom. That being said, you can fill the bag up to 3/4 full without any problem.

Posted on Jul 16, 2013

Ad

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

About 2 inches from the bottom of the bag.

Posted on Feb 22, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the motor pulley on a windsor versamatic vs14 vaccum


I own a few Windsors and I believe those pulleys are threaded on in reverse. Unfortunately there's nothing to grab hold of on the other end while turning the pulley with a pair of pliers. When servicing Hako machines I normally remove the armature from the motor and grab it with a towel while turning the pulley off. Give that a try, if no luck I'll get into one of my Windors and see how its configured.

Nov 27, 2017 | Windsor Vacuums

1 Answer

Where is vacuum chamber on a Windsor sensor xp12


it comes up from the back,it is probably plugged or the sensor is dirty

Apr 21, 2015 | Windsor Vacuums

1 Answer

How to fix sensor s12. red light for bag stays on even when vacuum bag is not full and the vacuum is clear


You most likely will need to change the Yoke assembly. There is a sensor built in that gets clogged with fine debris over time. This will take care of the problem.

Feb 09, 2015 | Windsor SR12 Sensor Bagged Upright Vacuum

2 Answers

I have windsor s12 red light for bag is full is on and it's not clogged. what next


Check the line going from the bottom of the vacuum to the bag, it may be clogged. A coat hanger can help you clear any jams, but be careful not to puncture the duct.

Jan 27, 2015 | Windsor SR12 Sensor Bagged Upright Vacuum

1 Answer

The handle release on windsor s12 won't spring into place


You likely have one of two problems. Your return spring is broken, or your axle is bent. If your axle is bent, carefully inspect your chassis to be sure that the bent axle has not cracked or otherwise damaged the chassis. I have included a parts list as well as some links to these parts for your reference. http://windsorvacuums.com/partslists/s12_PARTS.pdf 2010 Axle Spring 86146570 windsor allstar javelin 5053 Windsor Sensor Axle 86137990 allstar javelin

Jun 17, 2014 | Windsor VS14 Versamatic Bagged Upright...

4 Answers

I have a Windsor Sensor s12 and power shuts off after 5 min. of vacuuming. I'm wondering if it's overheating of if there is some other sensor that causes it to shut off.


Your Sensor most likely has an internal heat sensor that is shutting off the motor. Some vacuums install an external heat sensor with a reset button that you must push to re-start the vacuum. If your model does not have an external reset button it is most likely a sensor inside the motor. If it is defective the motor must be replaced to solve the problem. But first make sure the overheating is not being caused by a blockage somewhere or the bag is too full. Air must pass completely through a vacuum starting at the floor where it picks up the dirt through all the canisters, filters, bags, etc. and then is exhausted from the vacuum. Any restrictions or blockage can cause the motor to over heat.
That Vac Guy

Jan 04, 2013 | Windsor SR12 Sensor Bagged Upright Vacuum

1 Answer

Broken motor pulley windsor vacuum


I have the same problem, maybe we can flip the belt over and let it run on the smooth side for a while. That's what the person before me did and it lasted a good 6 months.

Feb 24, 2012 | Windsor VS14 Versamatic Bagged Upright...

1 Answer

My Windsor Versamatic plus has all of the sudden become very hard to push. I maintain this vaccum very well. It picks up fine, just to heavy tp push apparently


Likely the wheels are frozen with thread and hair at the sides of the wheels. Check for free movement of each wheel and pick out the debris around any that are hard to turn. Long needles and tweezers are good tools for this.

Jul 26, 2009 | Vacuums

Not finding what you are looking for?
Windsor VS14 Versamatic Bagged Upright Vacuum Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Windsor Vacuums Experts

Mike

Level 3 Expert

4367 Answers

Raymond Richards
Raymond Richards

Level 3 Expert

407 Answers

Thatvacguy.com

Level 3 Expert

1604 Answers

Are you a Windsor Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...