Question about Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

My whirlpool quiet partner II is not quiet at all. When I start the cycle it starts humming and a little vibrating and I open it up and no water. I close it and wait it out every 10 minutes I open it back up and no water. The heating element is hot and stinky since there's no water. But once the wash cycle is over the rinse cycle works and theres water. What's the issue?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Whirlpool Master
  • 53,765 Answers

Problem water inlet solenoid ( humming)
replace it and you get water

Posted on Sep 09, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
the dr

joey shearer

  • 447 Answers

SOURCE: Whirlpool DUC600XTPQ6 Quiet Partner I

Yes this is a heater fault detection error. The unit may not be heating the water resulting in unsanitary dishes so the unit shuts down in this fault. Also the door may not have completely shut resulting in the heater not working, but everything else does (the heater common line is broken at the door switch. Clear the fault by entering diagnostics with this key dance heated dry, normal, heated dry, normal. All the leds will light, you can then press cancel and try another wash cycle. If fault occurs again, you must repair heater problem.

Posted on Dec 23, 2007

aborcass

Ron Coons

  • 2651 Answers

SOURCE: Whirlpool Quiet Partner 980

clean light blinkin???? ry pushing the sanirinse-heated dry--sanirinse--heated dry. tha tshould put in diagnostic mode, there also should be a trouble shooter underthe lower acess panel

Posted on Apr 09, 2008

Anonymous

  • 1 Answer

SOURCE: Dishwasher (whirlpool quiet partner II)

I think I solved the door leaking problem by cleaning out the plastic filter screen on the inside (left) door panel. Didn't even know it was there, never knew it was suppose to be cleaned! It was so clogged and gross. I also discovered that my washer had shifted and was off balance. It has wood shims under the steel casing and one block was loose. No doubt from slamming and banging the door open and closed. Had to take the front skirt and kickplate off to see. I had my son use a lever and hoisted it up a little while I replaced the block shim now making the washer level again. Ran a light wash before fixing problems and it leaked. We ran a light wash after the fix's and so far so good. Haven't ran a regular longer wash yet. My water level was fine, no gasket problems, no washer wand cracks, etc... My husband was thrilled! When he came home, I informed him I have good news and not so good news. The not so good news was dinner was going to be late, the good news was I fixed the leaking (for months!)dishwasher and saved alot of money on repairs!

**Cleaned filter screen, made dishwasher level again.

Posted on Sep 09, 2008

xiamjoshx

  • 1 Answer

SOURCE: Whirlpool Quiet Partner II not washing or sensing.

I have a whirlpool quiet partner II and for some reason it does not drain the water out any more and I cannot figure out why....people say that it is the filter but that is unbelievably hard to get to and I cannot find any instructions online or paper work that tells how to break it down. If anyone has any insight please let me know

Posted on Nov 23, 2008

Paulo

  • 188 Answers

SOURCE: whirlpool quiet partner II top rack sprayer doesnt

The top rack spray arm doesn't work because of low water pressure from the wash motor or it's clogged with debris.
If the top spray arm looks clear of debris, remove the lower spray arm and lower feed tube to access the wash motor. Remove the 4 torx screws and the filter (accumulator assembly). Remove the torx screw and the inlet protector that covers the chopper assembly. Make sure the chopper is not broken (broken chopper will fill with debris and block water flow). While holding the chopper blade, reach inside the "D" shaped opening on top of the motor and spin the wheel/motor by hand in each direction to make sure either the chopper gear or the motor gear that drives the chopper is not broken. Replace the chopper if necessary (part # 8268383). If the motor gear is broken, replace the sump and motor assembly (part # 8535150). Remove any debris from the sump area in the process.
You don't have to shut the power off to the dishwasher because the door will be open, but if you feel more comfortable, do so.
Good luck!

Posted on Apr 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool quiet partner II starts and stops. What should I check?


the first thing to do is unplug it for 3 minutes then check to see if it reset by running

Jan 07, 2018 | Whirlpool 24 in. DU951PWB Free-standing...

1 Answer

Whirlpool quiet partner II stops running or won't complete it's was cycle, sometimes is will wash for a few minutes and stop or it will stop before the water even starts to flow.


I had the same problem with my dishwasher. After hearing that the motherboard was the problem I decided to take a closer look. There were two capacitors (1000 microfarads, 6.3 volts) that looked a little suspect. The tops of capacitors should be flat...these looked like soda cans that had been left in the freezer. Got on eBay, located the capacitors for roughly $3 and $4 shipping, for approx total of $10. Soldered the two new capacitors into the motherboard and put it back together. As soon as I closed the door, the dishwasher started draining the water. When I ran a Normal cycle it completed successfully. Saved myself over $120!

Aug 02, 2013 | Whirlpool Gold Dishwasher with Quiet...

1 Answer

Why did my quiet partner II whirlpool dishwash just stop mid cycle?


see this possible causes:
Water-heating cycle
heat, wash, and rinse has the 3 cicle, principal problem is the heat cycle, when the water reach the level ( by heating water elements) test the heating elements , most ot the time fixing this .the problem is o.k
Timer
sincerely. God bless you

May 04, 2012 | Whirlpool Dishwashers

1 Answer

I have a whirlpool Quiet partner II. It will not fill w/water.


ck the float in bottom of tank . it may be stuck n the up pos .. moce it up and down and listen for click of the sw .. very common . also the water valve may have failed and it will need replaceing . mm

Dec 07, 2009 | Washing Machines

1 Answer

I have the Whirlpool Quiet (??) Partner II. My


Have this same problem with my Whirlpool DU1145XTBA. Found out that when you start the unit, it fills with water. If the water does not rise above the filter mesh in the bottom center of the unit then the pump doesn't have enough water to supply pressure to the upper sprayer. Had to replace the Flow Meter. It tells the unit how much water to supply to the unit.

Apr 12, 2009 | Dishwashers

1 Answer

Whirlpool Quiet Partner II not washing or sensing.


I have a whirlpool quiet partner II and for some reason it does not drain the water out any more and I cannot figure out why....people say that it is the filter but that is unbelievably hard to get to and I cannot find any instructions online or paper work that tells how to break it down. If anyone has any insight please let me know

Nov 16, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Whirlpool GU2400XTP Built-in Dishwasher Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4367 Answers

Bruce Denton

Level 2 Expert

273 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...