Question about Kicker KX500.2 Car Audio Amplifier

1 Answer

2 channel amp to 6-6x9 wiring diagram

6 4ohm 6x9s to kicker kx500.2, is it possible ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 655 Answers

Hello magoocsl,

Yes, with the use of 2 high-pass and 1 low-pass crossovers, that Kicker amp will operate in what they call stereo and mono simultaneously (SAMS). You'd run 4 of the 6X9's in mono. Wire them in series-parallel with a low-pass crossover on the positive leg to the amp. The amp would see a 4ω load. The other two 6X9's would be wired as stereo, one to each channel with a high-pass crossover. Again, the amp sees a 4ω load.

Here's a link to the appropriate wiring diagram. The diagram is on page 5. Just substitute your 4 6X9's wired in series-parallel where they show the "mono" speaker.

http://www.kicker.com/sites/default/files/02KX300_400_500_800_2AmpManual.pdf

Hope this helps.

Posted on Apr 01, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I wire a 2ohm Kicker CVR with a 4ohm Kicker CVR to a monoblock amp 1 channel


yes. google, impedance calculator and it will help you out on how to wire it

Apr 12, 2015 | Kicker Car Audio & Video

1 Answer

I need to know how to wire 2 Kicker comp 10" subs


you can find your wiring diagram here
http://www.crutchfield.com/S-lCf6ewrWNQM/learn/learningcenter/car/subwoofers_wiring.html

Select from the list shown which describes your amp and subs (ie 2 channel amp with 2 4ohm subs)

Hope this helps and please rate, thanks

Mar 19, 2011 | Alpine MRP-M500 Car Audio Amplifier

1 Answer

Best way to connect a 15'' kicker cvr15 4 ohm dvc [single sealed box] and a volfenhag zx-4712 1000w 12'' 4ohm+4ohm dvc to my pyle 885 1000w 4 ch. bridgeable amp and how to wire the voice coils that are in...


best way is to just run the volfenhag with a set of wires for 2 channells(one set per coil) left and right @ 4 ohms per channell. The CVRs you can parallel the coils(2 ohms) and run a set from each sub to the amp in stereo left and right. This will give the kickers a little more juice than the 12 but should be fine.

Jan 25, 2010 | Rockford Fosgate Car Audio & Video

1 Answer

How to connect dual vouice coil to amp


Hey well your gonna need to give more info. is the sub dual 2ohm dual 4ohm. if you have a dual 2 ohm you wire one + to one- (like a jumper wire)and then your other +.- go to your amp as 4ohms, if you have a dual 4ohm model and your amp can handel 2ohm stereo then wire your +to+ to +on the amp and the same for your -. it will bring a 4ohms to 2 ohms by connecting pos. to pos. and neg.to neg. then to your amp.

Jan 18, 2010 | Kicker CVR12 Car Subwoofer

1 Answer

How do you wire four 12 inch kicker cvr dual voice coil, to a 2400 watt 1 channel class d amp


Hello brysonford00,

The wiring configuration depends on what final impedance you want the amp to see. If the subs are 4ohm DVC's, you can wire them to present a 2ohm impedance or an 8ohm impedance. The diagrams are here. If your subs are 2ohm DVC's, the wiring is the same. The impedances will be 1ohm and 4ohms.

Hope this helps.

Jun 07, 2009 | Kicker CVR12 Car Subwoofer

1 Answer

DONT KNOW HOW TO RUN 2 OHMS


Hello storres18,

If you have the Kicker model number 06CVX122, with dual 2ohm voice coils, they can be connected to a mono amp at 2ohms. First jumper the voice coils in series, the dotted positive (+) to the undotted negative (-) (or vice versa). Each sub is now 4ohms. Then wire both of the remaining positives and negatives together on the amp terminals (in parallel). The amp sees a 2ohm load. Here's the diagram:

8863dd7.gif
If you have the Kicker model number 06CVX124 with dual 4ohm voice coils, they cannot be wired to present a 2ohm load. They can only be wired as a 1ohm load (too low for the amp) or as a 4ohm load (at reduced power). Here is the diagram of the 4ohm wiring:

b50e52b.gif
Hope this helps.

May 10, 2009 | Visonik V900XD Car Audio Amplifier

1 Answer

CORRECT CONNECTION TO AMP BEING A FOUR TERMINAL SPEAKER


Hello i_starling,

The Kicker L7's come in either 2ohm or 4ohm dual voice coil (DVC) versions.

Whatever amp they are connected to, you need to know both the impedance of your L7's and the impedance of your amp. The L7's dual voice coils can be wired to provide a total of four different loads:

2ohm coils in parallel = 1ohm load
2ohm coils in series = 4ohm load
4ohm coils in parallel = 2ohm load
4ohm coils in series = 8ohm load

Your best connection would be the one that results in a final impedance load that is supported by the amp.

Hope this helps.


May 01, 2009 | Car Audio & Video

1 Answer

Wiring my kicker solo-baric 15's


The best you can do is connect the dual 2 ohm voice coils of each respective sub in series (4 ohms total per sub) and then connect each sub to one channel of the amp. This will give each sub 1000W, which is the rated maximum from Kicker.

Mar 13, 2008 | Kicker Solo-Baric L7 S15L72 Car Subwoofer

2 Answers

Subwoofer wiring diagram


parallel wiring. hook all 4 positives together and run to the positive output from the amp, hook all 4 negatives together and run to the negative output from the amp.

hope this helps,
trin

Nov 19, 2007 | Car Audio & Video

Not finding what you are looking for?
Kicker KX500.2 Car Audio Amplifier Logo

2,935 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kicker Car Audio & Video Experts

Professor_V
Professor_V

Level 2 Expert

93 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Dalynn Turner

Level 2 Expert

346 Answers

Are you a Kicker Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...