Question about Ariston Technologies Washing Machines

2 Answers

The washer is not completely getting filled with water

When i set the timer at 4 for cotton cl0thes the washer dosent get filled with water till the top.This has been happening from day1 and cant get the solution.my washing machine has three switches apart from temperature control and type of wash. they r one for spin on or off, the other main switch on or off and the third one for which i do not know the use. pls suggest solution.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 6,289 Answers

Some models use different water levels for different cycles. If that's the case with yours, There should be a diagram under lid.

Posted on Oct 04, 2017

Ad

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 17 Answers

This is normal , it takes small quantity of water unlikes old washing machines

Posted on Oct 04, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

  • 51 Answers

SOURCE: Will not drain or spin

Unless you jarred the machine it's the timer. You can check this by bypassing the lid switch and seeing if it will cycle.

Posted on Dec 13, 2007

keithd2704

Keith Deininger

  • 56 Answers

SOURCE: whirlpool washer ultimate care II lsq8500JQ1 top...Problem

Ok folks to change the lid switch on these and many top loading Whirlpool, Maytag, Kenmore, etc is quite easy.

Steps to replace the lid switch:

1. Remove unit from AC.
2. Remove the loading door from the unit, or using some duct tape tape it closed.
3. Using a small flat bladed screwdriver find the 2 release catches on the front of the unit between the top cover and front panel. These are just snap claps to hold the top cover down. To release the top you will need to compress the latch using the screwdriver. Start with one side, then the other. Once you have released both clips the lid will lift up just like the hood of your car.
4. You will now be able to remove the lid switch from the unit.
5. Install the new switch and close the hood of the unit.
6. Test the repair by running the unit though a complete cycle.

A great place to order the replacement part for the unit is:

www.appliancepartspros.com

They ship same day on orders placed before 3pm EST. Overnight shipping is available, however I usually opt for the 2-3 day ground shipping and save the money.

If this switch replacement does not take care of the problem, you might need to replace the control board located under the front panel. This replacement is also very easy and takes about 10 min from start to finish.

Hope this helps everyone. Cheers,

Keith

Posted on Oct 21, 2008

Anonymous

  • 1 Answer

SOURCE: GE TOP LOAD WASHER DOES NOT AGITATE OR SPIN

I have a GE MODEL WWSe5240G0WW top loader washer that has seen very little use. My problem is that the unit will not agitate or spin,every thing else seems to work ok. I did remove the top lid switch and jumped the to wires (Yellow/Red and Orange) still did not make any difference. Any in for would be great.

Posted on Feb 21, 2009

Anonymous

  • 1 Answer

SOURCE: Maytag Atlantis MAV6257AWW

I have a Maytag Atlantis MAV6257AWW. I need to replace the transmission. So I removed all four screws from the inner tub but I couldnt get the inner tub pull out, it's stuck.

From what I read on here, the seal nut doesn't have to be remove in order to remove the inner tub.

I tried every, I even hammer the shaft down from the inside of the tub but still no luck. Can someone help, thanks.

Posted on Oct 19, 2009

Anonymous

  • 1 Answer

SOURCE: simpson enduro 701 washing machine

you have a faulty brake motor. It pulls in and releases the brake. When pulled right it it contacts a switch which lets the other actions like washing and spinning to occur. $77 to $86 off ebay or appliance stores. turn off ac. remove back off machine. reach around left side of frame at the bottom of the tub and push the brake forward manually and let the little plastic retainer turn sideways and release the wire rope retainer that comes out of the brake motor. remove the power cable to the brake motor by pulling out the connector on the right side under the tub. remove the two 8mm screws retaining the brake motor and remove the brake motor. reverse procedure with new item.
enjoy uninterrupted washes!

Posted on Jun 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All lights are working belt is attached dunno why ifs not filling up or moving when I switch a wash program on but make a slight buzz as if it wants work


How to Check a Washer when Is Not Filling With Water OTHER washers test similiarly
# Test procedures to follow when a GE Hotpoint washer is not filling

* Disconnect the washer from the wall outlet
* Set the timer dial on regular and pull the knob to turn the timer push-pull switch on
* Set the temperature switch to the cold/cold setting
* Open the controls panel to gain access to the water mixing valve solenoids
* Touch the 2 terminals on the cold water solenoid with your volt meter test proves. Make sure that your body don't touch the washer cabinet, this eliminate the chance of getting an electrical shock.
* Have someone plug the washer cord for you while you check the voltage
* The reading should be 120 volts
* Disconnect the washer from the wall outlet
* Touch the 2 terminals on the hot water solenoid with your volt meter test proves. Remember, to keep your body from touching the washer cabinet to eliminate the chance of getting an electrical shock

#
2
Have your helper plug in the washer cord again so you could check the voltage at the hot water solenoid

* The reading should be 120 volts. If you get 120 volts, this tells you that the wall outlet, the timer, the water temperature switch cold and hot water settings are working ok.

#
3
If the GE Hotpoint washer is not filling, the problem should be on the water valve, the screen filters or the water supply
#
4
If one of the solenoids is bad you will need to replace the complete water mixing valve assembly YOU SHOULD ALSO GET AN OHMS READING OR SHOW CONTINUITY WHEN TESTED UNPLUGGED ON BOTH SELINOIDS HOT AND COLD




all-lights-working-belt-attached-dunno-fgv1ctnzjgewe3hu2qpqylbk-3-0.jpg

Mar 29, 2015 | Washing Machines

1 Answer

It takes more than 3 hours to complete a cycle


Hello there:
When the cycle doesn't advance, or it takes a very long time to complete a cycle.
!st, check the timer to see if it is working properly
if not replace it '
next make sure that you are getting cold water and it is getting adequate pressure.:
here is how to check the timer .
if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.
It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
Ok?
Hope this is very helpful for you
Best regards Michael

May 21, 2010 | GE 3.2 Cu. Ft. 8-Cycle Super Capacity...

1 Answer

The washing machinge is not completing the complete cycle


When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

Jul 11, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Water doesnt pump out to start rinse cycle


Seems the timer is sticking at the drain cycle. Manually move the timer and see if this helps. If this works then the timer is bad.

Jul 05, 2009 | Washing Machines

1 Answer

Washer fills with water, stops completely and does not go to the next cycle


Replace the timer.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 31, 2009 | Kenmore Washing Machines

1 Answer

Dishes not coming clean


Check to make sure that the drainline is not backed-up or obstructed. If water is draining properly, you may need to reprime your washer. It may have been turned off before being completing its cycle. To Prime, Start the dishwasher and slowly advance the timer, till you hear the water valve open and fill. Let the washer do the rest. If a loud whining noise appears and does not go away after filling, check the motor to make sure it is not locked up. If locked up. Turn washer off and attempt to turn the impellor. Once free, it should be ok

Jul 21, 2008 | Maytag Dishwashers

1 Answer

Kenmore stack washer and dryer


gabehart....sounds like belt is slipping. Replace it. The water pump is on a separate smaller motor so is not affected by the agitator/spin motor.

Jun 04, 2008 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

Older hotpoint washer


Sounds like a pressure switch problem not a timer. depending on the year and model they had alot of water level problems.

Apr 18, 2008 | Washing Machines

1 Answer

Timer on maytag Atlantis


replace water inlet solenoid first if this doesnt work replace timer

Dec 08, 2007 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Harjeet Singh

Level 2 Expert

109 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...