Question about Mitsubishi VS-50501 50" Rear Projection Television

1 Answer

Colors have seperated on tv, and curve

I have a hitachi 52 inch projection 53udx10b tv. the green and red colors have seperated on it, resulting in double vision on the screen. the picture is also curved towards the middle. any ideas? the bulbs are all lit, Malissa from New York

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

You have a convergence problem.
Maybe need change the IC of convergence, or the power supply of these parts.

Bye.

Posted on Apr 16, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE DOUBLE COLORS ON SCREEN THE RED AND THE BLEU AT ONCE ON AND I DON'T KNOW HOW TO ADJUST .


Projection TV sets have two very common problems listed below.

Problem #1) Convergence


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya https://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

May 24, 2009 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

All color guns out of alignment


Needs convergence amps replaced. Sometimes resistors burn and need to be replaced. This repair requires soldering/desoldering equip. and a trained eye, but usually can be done for 175.00-325.00 at a reputable service center. Good luck, Russmann.

Nov 01, 2008 | Hitachi 53UDX10B 53" Rear Projection...

2 Answers

Remote for hitachi 52 inch projection tv not working


1st step, replace battery of remote, no result, 2nd step, check / replace Remote Sensor of TV.

Aug 02, 2008 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Hitachi 53UDX10B PICTURE DISTORTION


projection screens are prone to screen burn ,this is caused by the same image being displayed for a long time ie nick jr image in the corner,also check ther are no magnets close to the tv as this will cause distortion,ie speakers etc,hope this helps

Jun 22, 2008 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Double image/ out of focus with green and blue seperation


Your tv is crt-based and is out of convergence. In other words, the settings for keeping the Red, Green and Blue images aligned have drifted and must be reset. This is common with CRT projectors and CRT rear projection tvs.

Refer to your owners manual for instructions on re-aligning it.

Apr 18, 2008 | Hitachi 51UWX20B 51" Rear Projection...

2 Answers

Convergance problems?


did you adjust the convergence
on the menu?

Jan 11, 2008 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

53UDX10B 53 in. Rear Projection "3D vision"


the convergence IC`s and associated resistors have to be replaced, do not repeatedly push magic focus or the alignment after the parts change out will take longer which of course means higher repair bill, good luck

Nov 10, 2007 | Hitachi 53SDX01B 53" Rear Projection...

1 Answer

53UDX10B 53 in. Rear Projection "3D vision"


I had the same problem with the same model earlier this year. You need to have the convergence module replaced on a circuit board inside. Expect to pay $400-$500 to a qualified repair shop.

Oct 11, 2007 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Hitachi 52 projection tv


use the advanced options page and reset the factor blue and red convergence defaults then do re apply the auto color defaults color at first it seemed very red (which is good because red was the missing factor in the green picture) but after reseting all the color and tints to the normal ranges I then reset the color auto correct again and all seems fine.

Jan 22, 2007 | Hitachi 50V710 50" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76171 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...