Question about Cisco Catalyst WS-CBS3130G-S Blade Switch

Open Question

Cisco Catalyst WS-CBS3130G-S - Cisco Catalyst WS-CBS3130G-S Blade Switch

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 16 Answers

SOURCE: catalyst ws-c2926 password recovery problem

  1. Attach a terminal or PC with terminal emulation to the console port of the switch. Use the following terminal settings:
    9600 baud rate
    No parity
    8 data bits
    No stop bit

  2. Unplug the power cable.
  3. Hold down the mode button while reconnecting the power cord to the switch. You can release the mode button a second or two after the LED above port 1x is no longer illuminated.
    The following instructions appear:
    The system has been interrupted prior to initializing the flash file system.
    The following commands will initialize the flash file system, and finish loading
    the operating system software:

    flash_init
    load_helper
    boot
  4. Type flash_init.
  5. Type load_helper.
  6. Type dir flash:. The switch file system is displayed:
    Directory of flash:
    2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA
    4 drwx 3776 Mar 01 1993 01:23:24 html
    66 -rwx 130 Jan 01 1970 00:01:19 env_vars
    68 -rwx 1296 Mar 01 1993 06:55:51 config.text
    1728000 bytes total (456704 bytes free)
  7. Type rename flash:config.text flash:config.old to rename the configuration file. This file contains the password definition.
  8. Type boot to boot the system.
  9. Enter N at the prompt to start the Setup program, Continue with the configuration dialog? [yes/no] : N
  10. At the switch prompt type en to turn on enable mode.
  11. Type rename flash:config.old flash:config.text to rename the configuration file with its original name.
  12. Copy the configuration file into memory: Switch# copy flash:config.text system:running-config
    Source filename [config.text]? (press Return)
    Destination filename [running-config]? (press Return)
    The configuration file is now reloaded.
  13. Change the password: switch#configure terminal
    switch(config)#enable password Cisco
    switch#control/Z
  14. Write the running configuration to the configuration file:
    switch(config)#write memory

Posted on Feb 09, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I need to buy a software license for WS-C2960S-48FPS-L?


No. WS C2960S 48FPS uses the Universal image, but no license is required. The feature is bound to the hardware model type and cannot be changed. For convenience, a single software image is used for all Cisco Catalyst 2960-S Series Switches, regardless of whether they are a LAN Base or LAN Lite model.

Jan 20, 2015 | Cisco Catalyst 2960 Ethernet Switch ...

1 Answer

The power devices that Cisco Catalyst 2960 Series Support?


The Cisco Catalyst 2960-48PST-L can support 48 PoE ports with total PoE power output capacity at 370W. Taking advantage of Cisco Catalyst Intelligent Power Management, the Cisco Catalyst 2960-48PST-L configuration can deliver the necessary power to support 24 ports at 15.4W, 48 ports at 7.7W, or any combination in between.

The Cisco Catalyst 2960-24PC-L can support 24 simultaneous full-powered PoE devices at 15.4W for maximum powered-device support.

The Cisco Catalyst 2960-24LT-L can support eight PoE devices at 15.4W
Cisco Catalyst 2960 Switches for the details

Aug 15, 2014 | Computers & Internet

1 Answer

Cisco 3524 not receiving vlan info


Try this http://tools.cisco.com/search/results/display?url=http%3a%2f%2fwww.cisco.com%2fc%2fdam%2fen%2fus%2fproducts%2fcollateral%2fswitches%2fnexus-4000-series-switches%2f6701_catswitch_guide_v7_r5.pdf&pos=5&query=WS-C3524-XL-EN

Mar 08, 2014 | Cisco Catalyst® WS-C3524-XL-EN 24-Port...

1 Answer

Cisco WS-C2960-24-S switch port not working


Can you tell more details, there's various possibilities to cause the switch not work...
You can check your switch from these way:
1 check your cenect cord
2 check the power supply
3 check your network environment

For the Cisco switches, if you have any problems you can feel free to send email to our technicist:
support@3anetwork.com
Cisco Price Cisco Switch Price Cisco Router Price Buy Cisco Switches...

Dec 14, 2012 | Cisco Catalyst 2960 24 10/100 (8 PoE)...

1 Answer

Hi, my cisco catalyst 2960 switch is not powering. what could be the problem?


Usually when cisco equipment behave like that, its a problem with the power module, and it's best to contact the supplier...If it's under warranty they should replace it. If it's not you may need to get a technician to open it upand check the power module

Jan 20, 2010 | Cisco Catalyst 2908 (WS-C2908-XL)...

1 Answer

Problem with module WS-X4548-GB-RJ45V in Catalyst 4506


use software advisor in Cisco website to verify it.just follow the process.

console to it and show diag and see whether it detectable or not.

hope this help.

Dec 02, 2006 | Cisco WS-X4548-GB-RJ45V= Expansion Module

Not finding what you are looking for?

Open Questions:

Cisco Catalyst WS-CBS3130G-S Blade Switch Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...