Question about Washing Machines

1 Answer

Whirlpool awm 1200/1

Machine works but when it gets to rinse stage stops leaving all clothes wet. Pump does not seem to work. Only way machine will continue is if I drain the water from the front of the machine from the small plastic filter. Is it something that could be fixed or is it easier to replace machine.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Washing Mach... Master
  • 2,699 Answers

Check the pump to see if anything is clogged in there or you could have a bad pump,open the door and look around the opening and you'll see the full model number.also if it stops at the rinse cycle does it fill with water and the water is in there but doesn't drain or are the clothes just sitting there wet,because when in rinse the machine just uses cold water and if the valve is clogged or filling slowly the washer will stop after like 6 minutes,does any error codes come up?you can try to start the washer just on cold water and see if the water fills slowly or if it comes in normally,if it comes in slow most likely that will be your problem,if it is the pump you can get a shop vac and suck out the water from the drain hose,get it as close to the floor as you can and it will work better,then remove the center part of the pump,the clean out and see if it's filled with stuff,turn it slowly,when water comes out vac it up with shop vac until it stops.hope this helps you out.

Posted on Feb 10, 2018

Ad

5 Suggested Answers

Master_Tech

Gary Davd

  • 770 Answers

SOURCE: Washer draining problem

I am sorry The model I was refering to was not yours... you have an OLD belt driven model there is a panel on the back (2) 5/16 screws to see the pump the best way to replace that hose if you have to is disconnet the fill lines pull the machine out from the wall and lay it on its back for easy access..

Posted on Feb 20, 2008

Ad

Anonymous

  • 156 Answers

SOURCE: spinning cycle

usey only takes about 2 tbs soap ather than that bad main board make sure you have cold water going in washer

Posted on Feb 25, 2008

johnychel

isaac johny

  • 796 Answers

SOURCE: spinning cycle

Keeping in mind that the soap & bleach gets dispensed into your wash on the second to last rinse cycle and that most all rinse cycles are in cold water. Is your cold water valve screen plugged causing your washer to rinse poorly? Are you using the HE detergent? If not maybe the washer is sudsing up to much and having a hard time rinsing all the suds and bleach out and leaving the clothes soapy.

Fill the washer up with no clothes in it on a cold/cold wash setting does it take a long time to fill the washer up? Also when it is full and agitating is there suds in the washer?

Last suggestion is if the drain is hose is a lot higher than the top of the washer it might have a hard time draining out all of the soap water before the next load

Posted on Mar 23, 2008

Jeff

  • 401 Answers

SOURCE: GE Top Load Heavy Duty Washer only works for small loads

Sounds like you need a new drive belt.

Posted on Jan 02, 2010

Testimonial: "Is this drive belt difficult of change? ... Are the belts expensive? Now I know, where to start looking at least. Cheers! "

beltronic205

Gerry Harvey

  • 1481 Answers

SOURCE: Whirlpool AWM 5080 stops during cycles

Sound like could be faulty pump however you need to make sure no
Could be pump at fault 1st you need to make sure no coin stuck in there ...




Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Samsung Model#WA5451ANW/XAA washer keeps repeating the rinse and spin cycle over and over and my clothes are still wet because spin cycle is not spinning clothes fast enough.


From the information you have supplied, I suspect that the machine is not draining the water away,
1] Check that the drain pump is working (it would be easier to hear it running, before the machine starts the spin cycle, or if your machine has a "drain down" feature)
2] If the pump is running, stop the machine and unplug it from the mains power. Remove the machine drain tube from the point where it is plumbed into the household waste pipe, and lay it down into a bucket, or large pan and allow the water to drain down [ you should expect to get up to 2 gallons (10 Litres) of water from the machine]
Allow the water to drain down completely by holding the drain hose as low as possible into the bucket.
3] once the water has drained completely, remove the drain hose from the pump and check that the drain hose is not blocked.
4] If the hose was clear, and the pump was running (in tests [1] & [2] ), it will be necessary to check that the drain pump, and the main hose from the tub to the pump are clear of obstructions.
Remove any foreign objects, and re-assemble the hoses to the pump to the machine, and the drain hose to the domestic plumbing.

Plug the machine into the mains power, and and set the machine to run on the "last rinse" and "spin" cycles and test to see if the problem has been rectified.

I hope this helps cure your problem.

Oct 13, 2016 | Samsung WA5451ANW 4.7 cu. ft. Top-Load...

1 Answer

Spinning cycle


Keeping in mind that the soap & bleach gets dispensed into your wash on the second to last rinse cycle and that most all rinse cycles are in cold water. Is your cold water valve screen plugged causing your washer to rinse poorly? Are you using the HE detergent? If not maybe the washer is sudsing up to much and having a hard time rinsing all the suds and bleach out and leaving the clothes soapy.

Fill the washer up with no clothes in it on a cold/cold wash setting does it take a long time to fill the washer up? Also when it is full and agitating is there suds in the washer?

Last suggestion is if the drain is hose is a lot higher than the top of the washer it might have a hard time draining out all of the soap water before the next load

Mar 23, 2008 | LG WM-2277HW Front Load Washer

1 Answer

Siemens avantgarde washing machin stopping at rinse stage


Does the washer pump out the water after the wash cycle? If not then check the drain lines coming from the pump to make sure that they are clear. Your pump not pumping will cause the machine to stop working as well

Mar 23, 2014 | Siemens Washing Machines

1 Answer

I have an asko 11505 clothes washer. For some reason, it is not going through all of the spinning cycle, it spins for a short time, then stops abrutely. I cleaned the coin stop, cleaned out all water...


My Asko 11505 washer fills only a little water then shuts off. If I drain the washer with the drain hose from under the machine, then the machine will start up and fill enough water to fill the hose again, then shut off.

Oct 19, 2009 | Asko Washing Machines

1 Answer

My machine will wash and rince but shuts off when


That may be dirt at the filter of the pump. check the drain hose aswell for any thing blocking the drain system. remove the hose before the drain pump.

Aug 06, 2009 | Frigidaire Affinity ATF6000F Front Load...

1 Answer

Won't complete cycle, stops at rinse. and can't get hot water.


Are you on well water? turn off the cold water to the washer and clean the screen filter out. do not leave filter out.
the machine probably has a cold only final rinse so it won't work properly.

Mar 22, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Leaves clothes very wet and soapy


Your pump is clogged. This stops the machine from spinning out or rinsing. You have to locate the thing, (comes under the tub, lower end of big black tube) take the clamps out to clear the muck. Refit as you have dismantled. First try to drain out the water completely or you will flood your room.

Mar 02, 2009 | Maytag Performa PAV3200

1 Answer

Dryer not working properly


its likely to be the condenser unit in the rear of the machine full with lint check for a large clear / opaque unit with pipes connected and make sure it is clear

Jun 19, 2008 | Equator EZ 3612 CEE Front Load...

3 Answers

Beko wma 510 washing machien leaving clothes un rinsed and wet.


Find out where your filter is & clean it out thoroughly, refit.

May 10, 2008 | Washing Machines

1 Answer

Kenmore Washing Machine doesn't rinse


The drain line is probably clogged. Maybe that a small sock or other piece of clothing get between the clothes tub and the outer tub that holds the water. Check as well that pump spins and clean from any clogged. Good luck!

Oct 08, 2006 | Kenmore 43042 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18166 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...