Question about Kidde 9000102 Night Hawk Combination Smoke/CO Alarm w/Voice/Alarm Warning KID9000102 KID 9000102

1 Answer

Alarm went off but no smoke was found and no other smells were detected. I do not believe that there was CO present. All the units were activated. after a period of time they stopped. This occurred 3 times within about 1.5 hours. On one unit a red light blinked. Not sure if another unit blinked

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Http://www.kidde.com/Documents/User-Guide-900-0102-A-ENG.pdf Remember that smoke take presidence over C/O detection so notice whats going off first . LED Indicator Operation
Red LED
The red LED will flash as described below under the following
conditions:
--During smoke or CO alarm, with every beep
--During testing (same as alarm)
--Low battery, single flash with chirp
--End of product life, double flash every 30 seconds with chirp
--Unit error mode, single flash with chirp
--Unit error mode, a Fault Code is flashed every 30 seconds (can
be observed and reported to customer service for
troubleshooting. Above is the user guide.

Posted on May 02, 2014

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Please advise the approx cost for installation of smoke alarm for 2 bedroom unit. Thank you


If you don't mind changing batteries every 6-12 months during the year then you can pick up these smoke alarms from any hardware or even discount store. The also come in blister packs (2 to 6 or more for value packs) Most will screw mount to attach to wall. You can also use self stick foam tape to 'stick it' anywhere. Try to put them in a high spot on wall or ceiling depending on the surface (crumbly textured surface won't stick well. It will have to be mounted with a screw) The higher locations will give you quicker response time but It's harder to get at without a step ladder. Lower units have slower response time as the smoke has to collect and lower to the point where the alarm is.
*** Note; you will need to check your fire code requirements for placement of alarms. (though once this minimal requirement is met there is no reason you can't add more in other locations for added coverage; like a large walk in closet, baby's room, laundry room, etc.)
* Getting back to your question, I'm guessing you have the updated required powered alarms or need to have a "Powered" fire alarm. The newer homes (well last 20 years is new to me) have low voltage power lines running from room to room where the alarms are placed. If you required to install this type of system then depending on the ceiling access (crawl space, lowered ceiling, etc.) and the need to run the wires "hidden" behind wall and ceiling will increase the installation time and labor costs. Electrician or authorized fire alarm technician will be needed. They should check your fire alarm requirements for you local, indicate locations for alarms, run wires, install and test. Check with several companies in your area and get several quotes. Check with Better Business Bureau for rating or complaints.
* With Smart ware being all the rage. It may be possible to use these "smart devices" to alert you to other situations besides just fire hazards. Break in, baby monitor, door ringer monitor, water (flooding), Carbon Monoxide, etc. But the alarm guy should be able to give you more options. Though I's still up to you how much you want to spend.
* Final; You check what the fire codes require. If they called you first then suspect a scam or a sales pitch to get you to buy something you don't require. You can always go with the 'stick on' alarms if that is allowed for your area. Call the fire Dept in your area. Those are the 'good guys' that want to keep you safe.
Aloha, ukeboy57

Jun 06, 2018 | Home

1 Answer

Smoke alarm went off None of the other smoke alarms went off just the 1 I have a CO alarm and that didnt go off either Smoke alarm has a green light on and a red light that flashes every 30 seconds


Most smoke alarms depend on a mirror and laser. If the one is question is near a bathroom, it probably went off after someone took a shower? The steam from the bathroom will fog the mirror and set it off. Same problem if it is near a source of cold air on a cold day with heat on in the house. If the problem is cold air from the attic, go to the attic and move the insulation. Seal the hole for the wires with canned foam like Great Stuff, and put the insulation back over it.

Jan 04, 2016 | Home

1 Answer

Wont stop beeping and saying fire, how do I stop it?


It sounds like you have a CO detector, or a combo smoke/CO detector. The alarm you are describing indicates that the unit is sensing carbon monoxide. If you are sure that none is present and the detector is mounted in a location suggested by the documentation, the detector is bad and should be replaced.

Oct 01, 2014 | Home

1 Answer

Why does alarm activate when there is no smell of smoke or fire not a battery operated unit 120v hard wired unit


The unit probably needs replacing (every 10 years by code for 120V smoke alarms; NFPA 72). Note that most 120V devices are of the ionization type and must be disposed of appropriately. The label on the under side of the device often has instructions. Also try searching for your model on the manufacturer's website.

Sep 15, 2014 | Home

1 Answer

Two of my smoke alarms went off (no fire/smoke in or near house), one has a green light blinking and one has a solid green light, which need a new battery/reset?


The constant green LED means the alarm has AC power.
A flashing green light every 2 seconds without an audible alert means the unit recently sounded ( was the one activated ) and is now in latching mode to let you know that it was the unit that detected the problem. To clear the latching mode hold down the test button for 5 seconds.
Red LED flashing once per minute means that the back-up battery is connected and functioning.
Red light flashing constantly during alarm means that it is the unit that initiated the alarm siren.

Sep 04, 2014 | Cars & Trucks

1 Answer

I have model kn-cob-lcb-ca...it does not have a digital display, it was made in 2009..a few nights ago it started beeping...4 beeps, 5 second pause then 4 beeps continuously..the manual says this is a...


send the detector back and have it replaced,
The CO sensor will not alarm to levels of CO below 30 ppm and will alarm in the following time range when exposed to the corresponding levels of CO: 70 ppm CO Concentration 60 - 240 minutes 150 ppm CO Concentration 10 - 50 minutes 400 ppm CO Concentration 4 - 15 minutes The alarm shall include a piezoelectric horn that is rated at 85 decibels at 10 feet. When the unit detects carbon monoxide, the alarm pattern will be four (4) short beeps - followed by five (5) seconds of silence - followed by four (4) short beeps. The unit shall incorporate 2 LED's. A green LED will be illuminated to indicate the alarm is operating properly when plugged into an outlet, and will flash every 10 seconds when on backup battery power. A red LED will flash to indicate that carbon monoxide has been detected until the device is reset or CO is eliminated or will flash to indicate low battery or alarm malfunction. The unit shall at a minimum meet the requirements of CAN/CSA 6.19-01. It shall also include a 10-year manufacturer's limited warranty or

Test/Reset Button - Tests the unit for proper operation. Resets the carbon monoxide alarm.
• Tamper Resist Feature - If activated, unit goes into constant alarm mode if it has been unplugged or has come loose from the outlet.

Sep 20, 2011 | Kidde Nighthawk Combo Gas/co Detector

1 Answer

I have a Kidde combo CO / Gas monitor. The last two mornings at almost the same time (7:00 AM) the alarm sounded with the word GAS displayed. The condition went away in about 30 seconds each time and the...


Besides the obvious jokes about gas in the bathroom, I would advise you move it out of the bath room. It is being affected by excessive moisture causing errors in the sensors. The same can happen for smoke alarms with condensation or other moisture sources. It should be located relatively close to a possible source of problem, but not right on top of it.

Is the shower in use at around 7 am every AM?

Nov 10, 2010 | Kidde Nighthawk Combo Gas/co Detector

1 Answer

One of the alarms is peeping every 30 seconds. Why and how do I stop it?


Normally this means the smoke detector's battery or batteries are getting weak and need to be replaced. Since your detector incorporates carbon monoxide detection it could also mean the sensor that measures CO is going bad. Most units with CO detection have a life expectancy of 8-10 years. If your unit is that old I would suggest replacing it. Hope this helps.

Aug 15, 2010 | First Alert SA302 Dual System Smoke...

1 Answer

Alarms go off with humidity.too sensitive.Any


All smoke detectors, whether they are of the photo-electronic or ionization type, can false alarm due to steam. There are basically two solutions to your problem. Either move the detector further away from these areas (I have found keeping a smoke detector at least 6 feet away from the bathroom door normally works) or if that is not practical, after showering try to evacuate steam by either opening a window or turning on the exhaust fan for several minutes before opening the bathroom door.

Oct 30, 2009 | Kidde 1275 Hardwire Smoke Alarm with Hush...

1 Answer

Went to a family dollar with a roof top unit and at the time could only check right above the drop ceiling, where there was a return and supply flex and a piece of square duct going through the roof and a...


sounds like a smoke detector to me. usually they just break the red or the green through a relay, if it smells smoke. could be dust burning off the heat strips first use, or you could get on the roof and find burned wires or motor. lots of old wires burning up with heat strips kicking in this time of year. i usually have em turn off alarm so fire dept wont come and turn to max heat and burn off the strips , measure amps, check wires, and all relays etc. you may have to bypass smoke detector till done. then return to correct "as found" wiring and reset alarms. hopefully no call backs. good luck.

Nov 21, 2008 | Heating & Cooling

Not finding what you are looking for?
Kidde 9000102 Night Hawk Combination Smoke/CO Alarm w/Voice/Alarm Warning KID9000102 KID 9000102 Logo

1,309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kidde Home Experts

 Henri P
Henri P

Level 2 Expert

48 Answers

Cindy Wells

Level 3 Expert

6048 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Kidde Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...