Question about Mitsubishi WS-73713 73" Rear Projection Television

Open Question

Replace dm board ws73713 - Mitsubishi WS-73713 73" Rear Projection Television

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Steve Yocum

  • 668 Answers

SOURCE: want to replace caps which board is the DM board?

Once you take the shield assembly off, you will see a board, I believe it is the DM Board board. There are four Capacitors grouped together probably rated at 35v 1000 mfd, 105 degree. They should be replaced with 35v 680mfd,105 degree Capacitors. Now once that is done, there is another board under that one. This is the Format Board. It also has 4 Capacitors that should also be replaced. They are the same value as the first Board and should be replaced with the same 35v 680mfd, 105 degree Capacitors.
Please note the Flex connectors at the bottom of the DM and Format Boards. They may not be available from Mitsubishi any more so be gentle with them and make sure the are installed properly when reinstalling the Boards back into the chassis. There is one other Board you should look at. The Power Supply Board is the board on the back of the chassis and also has a number of Capacitors that fail. Most all of the Capacitors that fail through out this chassis will have bulging tops. So any you see bulging, you should replace whether they are on the DM, Format , or Power Supply.
I hope this helps,
Skyassoc

Posted on Jan 07, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the dm in wd-52525


The DM is the second board inside the Chassis block directly underneath the FMT board. But replacement DM boards if still good are very expensive your better off replacing the 4 capacitors that fail on the DM.

Apr 03, 2013 | Mitsubishi WD-52525 52" Rear Projection...

2 Answers

Mitsubishi WD-52725 DLP DM board


The DM boards for that chassis are almost impossible to find if they are still good. Have you tried replacing the caps on the DM board that you have? Thats usually whats wrong are bad caps.

Mar 16, 2012 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

Mitsubishi dm baord repair


Repair for the dm board is to replace 30 smd caps. Smd caps are harder to replace than electolytic caps, unless you have great soldering skills, it's easy to break a trace. Might consider just replacing dm board.

Nov 27, 2011 | Televison & Video

2 Answers

We replaced the V26 dm repair kit and the problem still exists-tv won't turn on . What do you recommend?


Did you also replace the power capacitors on the power board. Usually the DM board and Power board caps together will cause the steady blinking led the DM caps alone only rarely cause the steady blinking led usually its a combination of both boards capoacitors failing.

Feb 17, 2011 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

Want to replace caps which board is the DM board?


Once you take the shield assembly off, you will see a board, I believe it is the DM Board board. There are four Capacitors grouped together probably rated at 35v 1000 mfd, 105 degree. They should be replaced with 35v 680mfd,105 degree Capacitors. Now once that is done, there is another board under that one. This is the Format Board. It also has 4 Capacitors that should also be replaced. They are the same value as the first Board and should be replaced with the same 35v 680mfd, 105 degree Capacitors.
Please note the Flex connectors at the bottom of the DM and Format Boards. They may not be available from Mitsubishi any more so be gentle with them and make sure the are installed properly when reinstalling the Boards back into the chassis. There is one other Board you should look at. The Power Supply Board is the board on the back of the chassis and also has a number of Capacitors that fail. Most all of the Capacitors that fail through out this chassis will have bulging tops. So any you see bulging, you should replace whether they are on the DM, Format , or Power Supply.
I hope this helps,
Skyassoc

Jan 07, 2010 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

Ws-55511 DM 5volts draged down blinking led


Hello,

Did you check the caps on the DM board? They usually go bad after a period of time. Remove the DM board and the metallic cover and there should be 4 to 7 capacitors (There are different revisions of the DM board). Check these caps also, replace if needed.

Thank you,

Shuttle83

http://www.electron-age-technologies-llc

Apr 05, 2009 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Constant green blinking light Mitsubishi tv WS-65513


Unplugged my Sony for 36 hours from wall and it solved the problem

Oct 20, 2008 | Mitsubishi WS-65869 65" Rear Projection...

1 Answer

Dm board (power supply) for mitsubishi rear projection tv (ws-55807)


Good day,

mohiuddin;

If the indicator stays on then you may have an DM PCB problem and to correct this do the the folowing:

SYMPTOM: Power LED does not stop blinking after plug in.

CURE: replace C9B01, C9B02,C9B10, and C9B11 (1000 uFD 16V) on the DM PCB. Replace them with part # 181P734030 (680uFd 16V).

The DM Board (PCB) is located on the very left side of the TV looking from back. Caution on removing Board and note what cables you disconnect to access the Metal Shielded Board.
Good Luck, big IRISH.

Jul 22, 2008 | Mitsubishi WS-55807 TV

1 Answer

Constant green blinking light Mitsubishi tv WS-65513


Please study the procedure at the following address.....
www.chrisandnat.com/projects/blinkingtv/blink.htm .....

use 1000mf 25v or 35v 105 degree capacitors to replace
original four 1000mf 16v..............if new ones are a little
too high,just lay them over on board........

Look it over..........let me know......................T.

Jan 07, 2008 | Mitsubishi WS-65513 65" Rear Projection...

4 Answers

Mitsubishi WS73713 - Now working - Timer light flashing.


hold menu button for 8 sec and then unplug for 1 minute. then when you plug it back in it will work after 1 minute

Dec 30, 2007 | Televison & Video

Not finding what you are looking for?
Mitsubishi WS-73713 73" Rear Projection Television Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...