Question about GE Energy Star 3.7 IEC Cu. Ft. Front Load Washer with Stainless Steel Basket

1 Answer

What is an E70 error code in a GE Adora Front load washer?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

E70 stands for a stuck key. Try unplug for 60 sec. Then try again. If not unplug and try to open and clean buttons of debris

Posted on Oct 27, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: Ge Adora Front Loader

If you have not already done so, clean the filter behind the panel in the front bottom of the washer. Remove the three philips head screws to get the panel off. Unscrew the plastic filter on the right hand side (use a shallow cake pan to catch any water). Remove the filter and clean out the pens, pencils, change, lint, etc... and put back in. All should work well after this. Thanks, Greg

Posted on Jan 03, 2008

Anonymous

  • 487 Answers

SOURCE: GE Adora front load washer overloaded now won't start

Washers - Resetting Electronic Controls on a Washer

If there is a pause in the washer cycle, the controls will lock up. The pause can occur because of a power failure or it was put in the test mode at the factory.

Also, if the washer was stopped before the cycle was complete or the consumer has pushed the stop/pause button to temporarily stop the cycle and the cycle is not reset. Over a period of 24 hours, the washer will pump out and spin, but will stay in the final spin.

To correct the situation, shut off the circuit breaker for 30 seconds or unplug the washer, then turn the timer knob around and back to any position other than final spin. Verify the water is turned on and restore power. This should resolve the issue.

Posted on Apr 23, 2008

Anonymous

  • 1185 Answers

SOURCE: cycles take too long

It is probably the fill valve filter which is blocked or the drain outlet is obstructed.
You can clean the fill valve filter by turning the water off and disconnecting the hose ot hoses

There is a plastic filter just inside the valve which needs to be kept clean

If you have a slow discharge from the drain pump that also will cause the machine to take a long time on a cycle

Take the discharge hose out of the waste pipe clean the end and get someone with strong lungs to blow down it you should be able to hear air bubbles inside the machine if not then you may have a sock stuck in the pipe from the drum to the pump

Posted on Jun 08, 2009

Daddy2keagan

Nathan Van Boven

  • 206 Answers

SOURCE: ge adora front load clothes washer washer smoke

new pump

Posted on Mar 22, 2011

Kayla Heindl

  • 46 Answers

SOURCE: Noise during spin cycle

what noise is it making, it may just be off balanced

Posted on Jan 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code E70 What is it?


E70 Stuck key Continuous key read for 60 seconds. Power down (unplug) machine, wait 30 seconds and retry. Use t04 test to test keys. Separate control and control housing from front panel - clean and remove foreign debris. Ensure all keys can be operated freely without sticking. Replace control panel if actions do not resolve. Maybe this will help

I’m happy to help further over the phone at https://www.6ya.com/expert/william_e43a8a4d83a5f604

Oct 27, 2013 | GE Adora Front Load Washing Machine Washer...

1 Answer

GE Adora front load washer turns until water is added then won't turn or spin


You should contact GE or qualified appliance repair center to be looked at professionally.

May 06, 2012 | GE Wh12x10309 Heater for Adora Front Load...

1 Answer

Noise during spin cycle


what noise is it making, it may just be off balanced

Jan 17, 2012 | GE WSXH208A Front Load Washer

2 Answers

AEG Lavamat 76810 E70 7Beeps Does seem to still work but display shows E70 and 7beeps over and over. Many thanks gary


I Have AEG Lavamat 76810 E70 7 Beeps and Beeps never stops

The water was not hot
I took all the multi-plugs out and put them back in the whole machine ALL CONNECTORS
Now it works fine E70 is gone

Jul 14, 2011 | AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

Washes starts buzzing and blinking and says e70


The e70 error code comes on when the hot and cold water hoses are reversed or not properly installed.

Feb 21, 2011 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

E70 error code


The main cause for this e70 error is that the hoses would have swapped (hot to cold, cold to hot). It means the washer isn't getting cold water.Try to switch between the hoses. Another possibility is the faucets are not turned on.... Hope this solution will fix your problem for sure.

Mar 30, 2010 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Washer won't drain


http://www.instructables.com/id/GE-Adora-Lint-Filter-Cleanout/?download=pdf

Had the same problem, this fixed it!

Aug 05, 2008 | GE Energy Star WCVH6260F Front Load Washer

Not finding what you are looking for?
GE Energy Star 3.7 IEC Cu. Ft. Front Load Washer with Stainless Steel Basket Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...