Question about Canon imageRUNNER 7200 Copier

Open Question

I have ir 7105 copy coming light, i change the toner & coronaa also change but the ault is there,

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 11 Answers

SOURCE: canon iR 7105

The Tray A Area Sensor Unit may be faulty. Replace the Sensor

Posted on Oct 28, 2008

Ad
redzventures

Jay Otaigbe

  • 149 Answers

SOURCE: I have an IR-3300 Model xerox machine. It was

The two problems may not be related. Adding toner should not under most circumstances cause copies to become light, unless the toner you are using is of a poor quality - I hope it is a Canon cartridge or quality generic. It sounds as though your fixing film or drum unit may need replacing, or perhaps you need to perform a install procedure. As the 'install - toner - start' option is free, try it first:

First press the head key and then the number '2' and '8' keys at the same time then press the head key again. This will take you into service mode - select 'copier' then 'install' then 'toner' then 'start'. This will run throught a cycle that takes a little while, I think about 599 seconds (sorry for been so accurate but unhelpful but that's what I remember from the display - never converted into minutes but you're welcome to).

But if you are having blurry or even dirty or light copies it may be the fixing film. When the copies are printed, immediately check if you can rub off the toner at all by rubbing the print with your fingers - if so this indicates that the fixing unit is not hot enough or there is not enough pressure - check that the fuser is in properly and that the jam release lever is not engaged.

Lastly, it could be your drum unit that is faulty or worn. Totest this you will need to try and stop the machine in the middle of printing before it reaches the fuser - open the front cover and latch down the transport bed with the green handle - remove the paper gently so as not to disturb the ink in any way and observe the image quality - if it is displaying the exact same symptoms then it is not your fuser and is probably the drum unit or dodgy toner - most likely the drum. However, if the image is fine, then it most definetely is your fuser film (and or perhaps the cleaning roller that cleans the film).

Good luck

Posted on Jul 31, 2009

sodeep

Sudeep Chatterjee

  • 3267 Answers

SOURCE: ir 6570 copy light

When you were replacing the drum did you tuch the drum surface?Best would be that you take some toner on piece of cloth, and polish the drum, while turning it in good direction, that the cleaning blade can clean it.After you must let it copy about 50 copies.

You can try to replace the whole drum unit cexv14, or clean the laser unit.

Also could it be that the toner unit, or toner cleaning blade are not properly distibutes the toner accross the developing/toner cylinder

Posted on May 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I want to know about Canon Image press 1110/1125/1135 these copiers use which type of toner. Can we put IR 5000 or IR 7105 toner in them How is the drum


no you can not, the toner in a image press is a dual component toner. in the 5000 and 7105 are a mono component toner please dont and if you did please tell the tech because it will drive him crazy trying to figure it out unless he is a veteran in the copier business.

Oct 17, 2015 | Canon Office Equipment & Supplies

1 Answer

Ir 7105 black copy is appear


I've had the Laser go bad on two occasions causing black or partial black copies

Feb 07, 2015 | Canon Ir7105 Ir 7105 Copiers1saddle Stitch...

1 Answer

Error code e121


Reader controler cooling fan fault replace the fan or dc board

Jul 17, 2013 | Canon Ir7105 Ir 7105 Copiers1saddle Stitch...

1 Answer

Ir 6570 copy light


When you were replacing the drum did you tuch the drum surface?Best would be that you take some toner on piece of cloth, and polish the drum, while turning it in good direction, that the cleaning blade can clean it.After you must let it copy about 50 copies.

You can try to replace the whole drum unit cexv14, or clean the laser unit.

Also could it be that the toner unit, or toner cleaning blade are not properly distibutes the toner accross the developing/toner cylinder

May 07, 2012 | Canon Office Equipment & Supplies

12 Answers

Cannon ir 3530 all error code and solution


Code Error name/description

E000 fixing overheating

E001 fixing assembly overheating

E002 fixing assembly low temperature

E003 post-standby fixing low temperature

E007 fixing film rotation error

E010 main motor rotation error

E014 fixing motor rotation error

E019 waste toner case full, waste toner case full sensor error

E020 toner clogging between sub hopper and developing assembly

E024 developing assembly connector disconnection

E025 hopper motor, bottle motor error

E032 NE controller counter error

E064 power supply voltage error (high-voltage)

E100 BD interval error

E110 scanner motor error

E191 communication error for high voltage power supply

E202 CIS home position detection error

E225 CIS light intensity error

E227 reader unit power supply error

E248 backup memory error

E261 zero-cross signal error

E315 image data error
E400 feeder communication error

Mar 03, 2011 | Canon ImageRUNNER 3570 Copier/Printer

1 Answer

Copy light


Hi

When you were replacing the drum did you tuch the drum surface?Best would be that you take some toner on piece of cloth, and polish the drum, while turning it in good direction, that the cleaning blade can clean it.After you must let it copy about 50 copies.

You can try to replace the whole drum unit cexv14, or clean the laser unit.

Also could it be that the toner unit, or toner cleaning blade are not properly distibutes the toner accross the developing/toner cylinder.

Nov 26, 2009 | Canon iR 2020i Laser Printer

1 Answer

Canon iR 7105


The Tray A Area Sensor Unit may be faulty. Replace the Sensor

Oct 27, 2008 | Canon imageRUNNER 7200 Copier

Not finding what you are looking for?
Canon imageRUNNER 7200 Copier Logo

Related Topics:

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...