Question about Delta Saws

1 Answer

Need wiring diagram for 230 v for delta table saw cat. #36-451

Wanting to change it from 120 volt to 230 volt and need wiring diagram to make change

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 72 Answers

Is the motor designed for dual voltages? The manual does not have a wiring diagram. I assume the motor lable diagram is faded or missing.

Dual voltage motors contain two sets of winding. Each set is rated for the lower voltage. To operate the motor on the higher voltage the windings must be connected in series. AND, they must be connected in the same direction. I use a variac to apply 30-40 VAC to the coils in various combinations, then measure the open lead voltage to determine the proper connections. This test should be performed by a licensed electrician.

Posted on Jun 26, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 12 Answers

SOURCE: on/off switch table saw

It sounds like you are wiring the switch wrong. Give me the model # and I will look for a wiring diagram for you.

Posted on Feb 25, 2009

efs_perpends

efs_perpends

  • 1996 Answers

SOURCE: I need a wiring diagram for a Delta xl-10 table saw.

Unfortunately, the manual for the XL-10 saw is no longer available online. Here is a link to the parts list and diagram.
If that is not helpful, please consult a qualified electrician, who should be able to guide you in the wiring of the switch and motor for that saw.
Without access to the schematic, I'm afraid the best solution to your wiring question is for some capable electrician to take a look at your saw in person.

Posted on Mar 31, 2009

A Miller

  • 8404 Answers

SOURCE: i need the wiring diagram for my 10 table saw

Im guessing ... the motor is 110 volt AC (AC dont care if it is coming or going) ... find the two terminals in the motor and hook the wires back up. If it HAPPENS to be incorrect, the saw will run poorly or the overload will trip.

I wouldnt be afraid to use this method on my craftsman table saw.

Posted on Nov 03, 2009

rowdy45176

David Ford

  • 2176 Answers

SOURCE: 10'' delta table saw manual

you might try Dewaltservicenet.com but you will need the model number and you might have to put the dash in between to get it to list the model. Let me know if you need more assistance and if you do I would also need this information.

Posted on Dec 08, 2009

VtToolMan

Mark

  • 704 Answers

SOURCE: I need a manual for a delta saw

Hello,

Here's a free manual you can download that provides an exploded view of all the parts and a complete listing of each part in the saw.

http://www.ereplacementparts.com/images/dewalt/34-670_Type_2.pdf

Here's a link to the Delta-Porter Cable website where you can also get a free manual via download. Just select which version you have, either Type 1 or Type 2 on the bottom of the page and download that for free

http://www.dewaltservicenet.com/SearchResults.aspx?q=34-670

Hope you find this Very Helpful and best regards!

Posted on Dec 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Open Question Wiring problem: I purchase a UST1072 AO Smith Pool motor. I have 230 volts. Does the black wire go to L1 and the white wire to L2? I have the ground wire connected.


measure across black and white if 230 volts L1 black and white L2 make sure to put black tape on end if measures 230 volts someone changed a wire to hot if only 120 volts across them see side of motor for low voltage wiring

Jun 02, 2018 | AO Smith Pool & Spa

1 Answer

Wire 230 volt air compressor wiring diagrams


On 230 volts you have 3 wires 2 are 115 volt and the third wire is ground. As long as you hook the ground wires together correctly the other wires don't matter. Usually the ground wire is either white or green. The black wires are hot (115 volts).

Feb 11, 2014 | Air Tools & Compressors

1 Answer

Where can i buy a 230 volt 120 watt wire in touch dimmer for a table lamp


Roger -

Are you sure you need a 230 volt dimmer in your table lamp? If this is being used in the US or Canada, it is more likely to be a 120 volt lamp. I think you will have trouble finding a 230 volt dimmer.

Jan 25, 2013 | Electrical Supplies

1 Answer

Century single phase 2 hp 3450 rpm type cs motor Frame f56


the motor is on 220 volts ,i like hook that up on 120 volts ,,thanks

May 10, 2012 | Air Tools & Compressors

1 Answer

I want to convert my compressor from 115 V to 220volt? There is nothing in the owners manual on how to do this. Can you help me?


Your garage mate unit was made to operate on 120 volts. That one reason there is nothing in the owners manual. To convert it my be costly.First your electric motor must be able to handle 220 volts. you will need to look on the motor tag and see if it has 120v/230v. if not you will have to purchase a new motor that will handle 220/230 volts.If your motor will handle 220/230/volts you need to look at the the wiring diagram attached to the motor. you then will need to purchase a 220 v plug and outlet and correct wire size to install.

Jun 21, 2011 | Ingersoll Rand - Rand 2 - hp 24 - gallon...

1 Answer

I want to run this compressor "RITIN RT2012" 2HP 12L (1.5kW) compressor. It's a 110V AC drive unit and I have 240V. Can I run it or do I need to convert the Power supply.


You can't just run it on the 240 Volt supply. Check the motor nameplate. If it says it is rated for 110/220 or 115/230, or 120/240 Volts, then it is capable of running at 240V. This will require a wiring change, and you may need a larger size power cord.
The electrical diagram should be on the motor name plate or under the cover to the electrical terminals on the motor.

May 25, 2011 | Air Tools & Compressors

1 Answer

I burned up a 1 1/2 Super Pump. I see it was originally wired for 120 and am wondering if I should wire it for 230 with my new pump. What are the advantages/disadvantages of 230 vs 120v.


120 volt carries a higher amperage through the circuit, while 220 carries a lower amperage through the circuit. Safety and wiring sizes come into play here. 230 will always be better over 120 for the above reasons, and also for the fact that it is more cost effective on your electrical bill.

wire your circuit and your pump for 220volt if possible. Only use 120 volts if you have to do it and theres no other options.

Apr 13, 2011 | Hayward SUPERPUMP 2.0 HP, 115/230V

1 Answer

Installing an 24,000btu air conditioner. The original wiring at that outlet has an double pole 20amp circuit breaker. The old air conditioner that was their was plug into an outlet box that sat on the face...


yes your ok if they say the unit doesn't need to be changed in the incomimg power from 208 up to 230 volts or vice-versa,normally they classify motors as120/208/ 230 /460 volts, instead of 120/240/480 volts,but all line voltage varies in this voltage range between 230 to 255 volts a.c. with a +10/-10 percent tolerance either way,and as long as the instructions dont say anything about changing motor connections your good to go, just look on the motor body if possible and make sure theres no wiring diagrams to change voltage,but i would say no in a package A/C like that, and as far as the current goes your good with the 20 amp tandem pole breaker,let me know if i can further assist you. thanks

Jul 17, 2010 | ACE -Air 24,000BTU Heat Pump A/C Free DVD...

2 Answers

Just bought a campbellhausfeld fl3307 compressor at an auction did not realize that it has mc94 2 hp moter which is wired for 230volts but my garage is not On the compressor it says engine can run on 120...


The wiring diagram to change the voltage is on the name plate on the motor. The motor leads are numbered. Go by the diagram and reconnect the numbered leads the way it says for 'low voltage'

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Sep 23, 2009 | Air Tools & Compressors

Not finding what you are looking for?
Saws Logo

Related Topics:

464 people viewed this question

Ask a Question

Usually answered in minutes!

Top Delta Saws Experts

John Trevino

Level 3 Expert

1420 Answers

Asmodius

Level 1 Expert

12 Answers

ray gallant

Level 3 Expert

66248 Answers

Are you a Delta Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...